drivers/spi/spi-qcom-qspi.c

// SPDX-License-Identifier: GPL-2.0
// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.

#include <linux/clk.h>
#include <linux/dmapool.h>
#include <linux/dma-mapping.h>
#include <linux/interconnect.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm_runtime.h>
#include <linux/pm_opp.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi-mem.h>


#define QSPI_NUM_CS		2
#define QSPI_BYTES_PER_WORD	4

#define MSTR_CONFIG		0x0000
#define FULL_CYCLE_MODE		BIT(3)
#define FB_CLK_EN		BIT(4)
#define PIN_HOLDN		BIT(6)
#define PIN_WPN			BIT(7)
#define DMA_ENABLE		BIT(8)
#define BIG_ENDIAN_MODE		BIT(9)
#define SPI_MODE_MSK		0xc00
#define SPI_MODE_SHFT		10
#define CHIP_SELECT_NUM		BIT(12)
#define SBL_EN			BIT(13)
#define LPA_BASE_MSK		0x3c000
#define LPA_BASE_SHFT		14
#define TX_DATA_DELAY_MSK	0xc0000
#define TX_DATA_DELAY_SHFT	18
#define TX_CLK_DELAY_MSK	0x300000
#define TX_CLK_DELAY_SHFT	20
#define TX_CS_N_DELAY_MSK	0xc00000
#define TX_CS_N_DELAY_SHFT	22
#define TX_DATA_OE_DELAY_MSK	0x3000000
#define TX_DATA_OE_DELAY_SHFT	24

#define AHB_MASTER_CFG				0x0004
#define HMEM_TYPE_START_MID_TRANS_MSK		0x7
#define HMEM_TYPE_START_MID_TRANS_SHFT		0
#define HMEM_TYPE_LAST_TRANS_MSK		0x38
#define HMEM_TYPE_LAST_TRANS_SHFT		3
#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_MSK	0xc0
#define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_SHFT	6
#define HMEMTYPE_READ_TRANS_MSK			0x700
#define HMEMTYPE_READ_TRANS_SHFT		8
#define HSHARED					BIT(11)
#define HINNERSHARED				BIT(12)

#define MSTR_INT_EN		0x000C
#define MSTR_INT_STATUS		0x0010
#define RESP_FIFO_UNDERRUN	BIT(0)
#define RESP_FIFO_NOT_EMPTY	BIT(1)
#define RESP_FIFO_RDY		BIT(2)
#define HRESP_FROM_NOC_ERR	BIT(3)
#define WR_FIFO_EMPTY		BIT(9)
#define WR_FIFO_FULL		BIT(10)
#define WR_FIFO_OVERRUN		BIT(11)
#define TRANSACTION_DONE	BIT(16)
#define DMA_CHAIN_DONE		BIT(31)
#define QSPI_ERR_IRQS		(RESP_FIFO_UNDERRUN | HRESP_FROM_NOC_ERR | \
				 WR_FIFO_OVERRUN)
#define QSPI_ALL_IRQS		(QSPI_ERR_IRQS | RESP_FIFO_RDY | \
				 WR_FIFO_EMPTY | WR_FIFO_FULL | \
				 TRANSACTION_DONE | DMA_CHAIN_DONE)

#define PIO_XFER_CTRL		0x0014
#define REQUEST_COUNT_MSK	0xffff

#define PIO_XFER_CFG		0x0018
#define TRANSFER_DIRECTION	BIT(0)
#define MULTI_IO_MODE_MSK	0xe
#define MULTI_IO_MODE_SHFT	1
#define TRANSFER_FRAGMENT	BIT(8)
#define SDR_1BIT		1
#define SDR_2BIT		2
#define SDR_4BIT		3
#define DDR_1BIT		5
#define DDR_2BIT		6
#define DDR_4BIT		7
#define DMA_DESC_SINGLE_SPI	1
#define DMA_DESC_DUAL_SPI	2
#define DMA_DESC_QUAD_SPI	3

#define PIO_XFER_STATUS		0x001c
#define WR_FIFO_BYTES_MSK	0xffff0000
#define WR_FIFO_BYTES_SHFT	16

#define PIO_DATAOUT_1B		0x0020
#define PIO_DATAOUT_4B		0x0024

#define RD_FIFO_CFG		0x0028
#define CONTINUOUS_MODE		BIT(0)

#define RD_FIFO_STATUS	0x002c
#define FIFO_EMPTY	BIT(11)
#define WR_CNTS_MSK	0x7f0
#define WR_CNTS_SHFT	4
#define RDY_64BYTE	BIT(3)
#define RDY_32BYTE	BIT(2)
#define RDY_16BYTE	BIT(1)
#define FIFO_RDY	BIT(0)

#define RD_FIFO_RESET		0x0030
#define RESET_FIFO		BIT(0)

#define NEXT_DMA_DESC_ADDR	0x0040
#define CURRENT_DMA_DESC_ADDR	0x0044
#define CURRENT_MEM_ADDR	0x0048

#define CUR_MEM_ADDR		0x0048
#define HW_VERSION		0x004c
#define RD_FIFO			0x0050
#define SAMPLING_CLK_CFG	0x0090
#define SAMPLING_CLK_STATUS	0x0094

#define QSPI_ALIGN_REQ	32

enum qspi_dir {
	QSPI_READ,
	QSPI_WRITE,
};

struct qspi_cmd_desc {
	u32 data_address;
	u32 next_descriptor;
	u32 direction:1;
	u32 multi_io_mode:3;
	u32 reserved1:4;
	u32 fragment:1;
	u32 reserved2:7;
	u32 length:16;
};

struct qspi_xfer {
	union {
		const void *tx_buf;
		void *rx_buf;
	};
	unsigned int rem_bytes;
	unsigned int buswidth;
	enum qspi_dir dir;
	bool is_last;
};

enum qspi_clocks {
	QSPI_CLK_CORE,
	QSPI_CLK_IFACE,
	QSPI_NUM_CLKS
};

/*
 * Number of entries in sgt returned from spi framework that-
 * will be supported. Can be modified as required.
 * In practice, given max_dma_len is 64KB, the number of
 * entries is not expected to exceed 1.
 */
#define QSPI_MAX_SG 5

struct qcom_qspi {
	void __iomem *base;
	struct device *dev;
	struct clk_bulk_data *clks;
	struct qspi_xfer xfer;
	struct dma_pool *dma_cmd_pool;
	dma_addr_t dma_cmd_desc[QSPI_MAX_SG];
	void *virt_cmd_desc[QSPI_MAX_SG];
	unsigned int n_cmd_desc;
	struct icc_path *icc_path_cpu_to_qspi;
	unsigned long last_speed;
	/* Lock to protect data accessed by IRQs */
	spinlock_t lock;
};

static u32 qspi_buswidth_to_iomode(struct qcom_qspi *ctrl,
				   unsigned int buswidth)
{
	switch (buswidth) {
	case 1:
		return SDR_1BIT;
	case 2:
		return SDR_2BIT;
	case 4:
		return SDR_4BIT;
	default:
		dev_warn_once(ctrl->dev,
				"Unexpected bus width: %u\n", buswidth);
		return SDR_1BIT;
	}
}

static void qcom_qspi_pio_xfer_cfg(struct qcom_qspi *ctrl)
{
	u32 pio_xfer_cfg;
	u32 iomode;
	const struct qspi_xfer *xfer;

	xfer = &ctrl->xfer;
	pio_xfer_cfg = readl(ctrl->base + PIO_XFER_CFG);
	pio_xfer_cfg &= ~TRANSFER_DIRECTION;
	pio_xfer_cfg |= xfer->dir;
	if (xfer->is_last)
		pio_xfer_cfg &= ~TRANSFER_FRAGMENT;
	else
		pio_xfer_cfg |= TRANSFER_FRAGMENT;
	pio_xfer_cfg &= ~MULTI_IO_MODE_MSK;
	iomode = qspi_buswidth_to_iomode(ctrl, xfer->buswidth);
	pio_xfer_cfg |= iomode << MULTI_IO_MODE_SHFT;

	writel(pio_xfer_cfg, ctrl->base + PIO_XFER_CFG);
}

static void qcom_qspi_pio_xfer_ctrl(struct qcom_qspi *ctrl)
{
	u32 pio_xfer_ctrl;

	pio_xfer_ctrl = readl(ctrl->base + PIO_XFER_CTRL);
	pio_xfer_ctrl &= ~REQUEST_COUNT_MSK;
	pio_xfer_ctrl |= ctrl->xfer.rem_bytes;
	writel(pio_xfer_ctrl, ctrl->base + PIO_XFER_CTRL);
}

static void qcom_qspi_pio_xfer(struct qcom_qspi *ctrl)
{
	u32 ints;

	qcom_qspi_pio_xfer_cfg(ctrl);

	/* Ack any previous interrupts that might be hanging around */
	writel(QSPI_ALL_IRQS, ctrl->base + MSTR_INT_STATUS);

	/* Setup new interrupts */
	if (ctrl->xfer.dir == QSPI_WRITE)
		ints = QSPI_ERR_IRQS | WR_FIFO_EMPTY;
	else
		ints = QSPI_ERR_IRQS | RESP_FIFO_RDY;
	writel(ints, ctrl->base + MSTR_INT_EN);

	/* Kick off the transfer */
	qcom_qspi_pio_xfer_ctrl(ctrl);
}

static void qcom_qspi_handle_err(struct spi_controller *host,
				 struct spi_message *msg)
{
	u32 int_status;
	struct qcom_qspi *ctrl = spi_controller_get_devdata(host);
	unsigned long flags;
	int i;

	spin_lock_irqsave(&ctrl->lock, flags);
	writel(0, ctrl->base + MSTR_INT_EN);
	int_status = readl(ctrl->base + MSTR_INT_STATUS);
	writel(int_status, ctrl->base + MSTR_INT_STATUS);
	ctrl->xfer.rem_bytes = 0;

	/* free cmd descriptors if they are around (DMA mode) */
	for (i = 0; i < ctrl->n_cmd_desc; i++)
		dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
				  ctrl->dma_cmd_desc[i]);
	ctrl->n_cmd_desc = 0;
	spin_unlock_irqrestore(&ctrl->lock, flags);
}

static int qcom_qspi_set_speed(struct qcom_qspi *ctrl, unsigned long speed_hz)
{
	int ret;
	unsigned int avg_bw_cpu;

	if (speed_hz == ctrl->last_speed)
		return 0;

	/* In regular operation (SBL_EN=1) core must be 4x transfer clock */
	ret = dev_pm_opp_set_rate(ctrl->dev, speed_hz * 4);
	if (ret) {
		dev_err(ctrl->dev, "Failed to set core clk %d\n", ret);
		return ret;
	}

	/*
	 * Set BW quota for CPU.
	 * We don't have explicit peak requirement so keep it equal to avg_bw.
	 */
	avg_bw_cpu = Bps_to_icc(speed_hz);
	ret = icc_set_bw(ctrl->icc_path_cpu_to_qspi, avg_bw_cpu, avg_bw_cpu);
	if (ret) {
		dev_err(ctrl->dev, "%s: ICC BW voting failed for cpu: %d\n",
			__func__, ret);
		return ret;
	}

	ctrl->last_speed = speed_hz;

	return 0;
}

static int qcom_qspi_alloc_desc(struct qcom_qspi *ctrl, dma_addr_t dma_ptr,
			uint32_t n_bytes)
{
	struct qspi_cmd_desc *virt_cmd_desc, *prev;
	dma_addr_t dma_cmd_desc;

	/* allocate for dma cmd descriptor */
	virt_cmd_desc = dma_pool_alloc(ctrl->dma_cmd_pool, GFP_ATOMIC | __GFP_ZERO, &dma_cmd_desc);
	if (!virt_cmd_desc) {
		dev_warn_once(ctrl->dev, "Couldn't find memory for descriptor\n");
		return -EAGAIN;
	}

	ctrl->virt_cmd_desc[ctrl->n_cmd_desc] = virt_cmd_desc;
	ctrl->dma_cmd_desc[ctrl->n_cmd_desc] = dma_cmd_desc;
	ctrl->n_cmd_desc++;

	/* setup cmd descriptor */
	virt_cmd_desc->data_address = dma_ptr;
	virt_cmd_desc->direction = ctrl->xfer.dir;
	virt_cmd_desc->multi_io_mode = qspi_buswidth_to_iomode(ctrl, ctrl->xfer.buswidth);
	virt_cmd_desc->fragment = !ctrl->xfer.is_last;
	virt_cmd_desc->length = n_bytes;

	/* update previous descriptor */
	if (ctrl->n_cmd_desc >= 2) {
		prev = (ctrl->virt_cmd_desc)[ctrl->n_cmd_desc - 2];
		prev->next_descriptor = dma_cmd_desc;
		prev->fragment = 1;
	}

	return 0;
}

static int qcom_qspi_setup_dma_desc(struct qcom_qspi *ctrl,
				struct spi_transfer *xfer)
{
	int ret;
	struct sg_table *sgt;
	dma_addr_t dma_ptr_sg;
	unsigned int dma_len_sg;
	int i;

	if (ctrl->n_cmd_desc) {
		dev_err(ctrl->dev, "Remnant dma buffers n_cmd_desc-%d\n", ctrl->n_cmd_desc);
		return -EIO;
	}

	sgt = (ctrl->xfer.dir == QSPI_READ) ? &xfer->rx_sg : &xfer->tx_sg;
	if (!sgt->nents || sgt->nents > QSPI_MAX_SG) {
		dev_warn_once(ctrl->dev, "Cannot handle %d entries in scatter list\n", sgt->nents);
		return -EAGAIN;
	}

	for (i = 0; i < sgt->nents; i++) {
		dma_ptr_sg = sg_dma_address(sgt->sgl + i);
		dma_len_sg = sg_dma_len(sgt->sgl + i);
		if (!IS_ALIGNED(dma_ptr_sg, QSPI_ALIGN_REQ)) {
			dev_warn_once(ctrl->dev, "dma_address not aligned to %d\n", QSPI_ALIGN_REQ);
			return -EAGAIN;
		}
		/*
		 * When reading with DMA the controller writes to memory 1 word
		 * at a time. If the length isn't a multiple of 4 bytes then
		 * the controller can clobber the things later in memory.
		 * Fallback to PIO to be safe.
		 */
		if (ctrl->xfer.dir == QSPI_READ && (dma_len_sg & 0x03)) {
			dev_warn_once(ctrl->dev, "fallback to PIO for read of size %#010x\n",
				      dma_len_sg);
			return -EAGAIN;
		}
	}

	for (i = 0; i < sgt->nents; i++) {
		dma_ptr_sg = sg_dma_address(sgt->sgl + i);
		dma_len_sg = sg_dma_len(sgt->sgl + i);

		ret = qcom_qspi_alloc_desc(ctrl, dma_ptr_sg, dma_len_sg);
		if (ret)
			goto cleanup;
	}
	return 0;

cleanup:
	for (i = 0; i < ctrl->n_cmd_desc; i++)
		dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
				  ctrl->dma_cmd_desc[i]);
	ctrl->n_cmd_desc = 0;
	return ret;
}

static void qcom_qspi_dma_xfer(struct qcom_qspi *ctrl)
{
	/* Setup new interrupts */
	writel(DMA_CHAIN_DONE, ctrl->base + MSTR_INT_EN);

	/* kick off transfer */
	writel((u32)((ctrl->dma_cmd_desc)[0]), ctrl->base + NEXT_DMA_DESC_ADDR);
}

/* Switch to DMA if transfer length exceeds this */
#define QSPI_MAX_BYTES_FIFO 64

static bool qcom_qspi_can_dma(struct spi_controller *ctlr,
			 struct spi_device *slv, struct spi_transfer *xfer)
{
	return xfer->len > QSPI_MAX_BYTES_FIFO;
}

static int qcom_qspi_transfer_one(struct spi_controller *host,
				  struct spi_device *slv,
				  struct spi_transfer *xfer)
{
	struct qcom_qspi *ctrl = spi_controller_get_devdata(host);
	int ret;
	unsigned long speed_hz;
	unsigned long flags;
	u32 mstr_cfg;

	speed_hz = slv->max_speed_hz;
	if (xfer->speed_hz)
		speed_hz = xfer->speed_hz;

	ret = qcom_qspi_set_speed(ctrl, speed_hz);
	if (ret)
		return ret;

	spin_lock_irqsave(&ctrl->lock, flags);
	mstr_cfg = readl(ctrl->base + MSTR_CONFIG);

	/* We are half duplex, so either rx or tx will be set */
	if (xfer->rx_buf) {
		ctrl->xfer.dir = QSPI_READ;
		ctrl->xfer.buswidth = xfer->rx_nbits;
		ctrl->xfer.rx_buf = xfer->rx_buf;
	} else {
		ctrl->xfer.dir = QSPI_WRITE;
		ctrl->xfer.buswidth = xfer->tx_nbits;
		ctrl->xfer.tx_buf = xfer->tx_buf;
	}
	ctrl->xfer.is_last = list_is_last(&xfer->transfer_list,
					  &host->cur_msg->transfers);
	ctrl->xfer.rem_bytes = xfer->len;

	if (xfer->rx_sg.nents || xfer->tx_sg.nents) {
		/* do DMA transfer */
		if (!(mstr_cfg & DMA_ENABLE)) {
			mstr_cfg |= DMA_ENABLE;
			writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
		}

		ret = qcom_qspi_setup_dma_desc(ctrl, xfer);
		if (ret != -EAGAIN) {
			if (!ret) {
				dma_wmb();
				qcom_qspi_dma_xfer(ctrl);
			}
			goto exit;
		}
		dev_warn_once(ctrl->dev, "DMA failure, falling back to PIO\n");
		ret = 0; /* We'll retry w/ PIO */
	}

	if (mstr_cfg & DMA_ENABLE) {
		mstr_cfg &= ~DMA_ENABLE;
		writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
	}
	qcom_qspi_pio_xfer(ctrl);

exit:
	spin_unlock_irqrestore(&ctrl->lock, flags);

	if (ret)
		return ret;

	/* We'll call spi_finalize_current_transfer() when done */
	return 1;
}

static int qcom_qspi_prepare_message(struct spi_controller *host,
				     struct spi_message *message)
{
	u32 mstr_cfg;
	struct qcom_qspi *ctrl;
	int tx_data_oe_delay = 1;
	int tx_data_delay = 1;
	unsigned long flags;

	ctrl = spi_controller_get_devdata(host);
	spin_lock_irqsave(&ctrl->lock, flags);

	mstr_cfg = readl(ctrl->base + MSTR_CONFIG);
	mstr_cfg &= ~CHIP_SELECT_NUM;
	if (spi_get_chipselect(message->spi, 0))
		mstr_cfg |= CHIP_SELECT_NUM;

	mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE;
	mstr_cfg &= ~(SPI_MODE_MSK | TX_DATA_OE_DELAY_MSK | TX_DATA_DELAY_MSK);
	mstr_cfg |= message->spi->mode << SPI_MODE_SHFT;
	mstr_cfg |= tx_data_oe_delay << TX_DATA_OE_DELAY_SHFT;
	mstr_cfg |= tx_data_delay << TX_DATA_DELAY_SHFT;
	mstr_cfg &= ~DMA_ENABLE;

	writel(mstr_cfg, ctrl->base + MSTR_CONFIG);
	spin_unlock_irqrestore(&ctrl->lock, flags);

	return 0;
}

static int qcom_qspi_alloc_dma(struct qcom_qspi *ctrl)
{
	ctrl->dma_cmd_pool = dmam_pool_create("qspi cmd desc pool",
		ctrl->dev, sizeof(struct qspi_cmd_desc), 0, 0);
	if (!ctrl->dma_cmd_pool)
		return -ENOMEM;

	return 0;
}

static irqreturn_t pio_read(struct qcom_qspi *ctrl)
{
	u32 rd_fifo_status;
	u32 rd_fifo;
	unsigned int wr_cnts;
	unsigned int bytes_to_read;
	unsigned int words_to_read;
	u32 *word_buf;
	u8 *byte_buf;
	int i;

	rd_fifo_status = readl(ctrl->base + RD_FIFO_STATUS);

	if (!(rd_fifo_status & FIFO_RDY)) {
		dev_dbg(ctrl->dev, "Spurious IRQ %#x\n", rd_fifo_status);
		return IRQ_NONE;
	}

	wr_cnts = (rd_fifo_status & WR_CNTS_MSK) >> WR_CNTS_SHFT;
	wr_cnts = min(wr_cnts, ctrl->xfer.rem_bytes);

	words_to_read = wr_cnts / QSPI_BYTES_PER_WORD;
	bytes_to_read = wr_cnts % QSPI_BYTES_PER_WORD;

	if (words_to_read) {
		word_buf = ctrl->xfer.rx_buf;
		ctrl->xfer.rem_bytes -= words_to_read * QSPI_BYTES_PER_WORD;
		ioread32_rep(ctrl->base + RD_FIFO, word_buf, words_to_read);
		ctrl->xfer.rx_buf = word_buf + words_to_read;
	}

	if (bytes_to_read) {
		byte_buf = ctrl->xfer.rx_buf;
		rd_fifo = readl(ctrl->base + RD_FIFO);
		ctrl->xfer.rem_bytes -= bytes_to_read;
		for (i = 0; i < bytes_to_read; i++)
			*byte_buf++ = rd_fifo >> (i * BITS_PER_BYTE);
		ctrl->xfer.rx_buf = byte_buf;
	}

	return IRQ_HANDLED;
}

static irqreturn_t pio_write(struct qcom_qspi *ctrl)
{
	const void *xfer_buf = ctrl->xfer.tx_buf;
	const int *word_buf;
	const char *byte_buf;
	unsigned int wr_fifo_bytes;
	unsigned int wr_fifo_words;
	unsigned int wr_size;
	unsigned int rem_words;

	wr_fifo_bytes = readl(ctrl->base + PIO_XFER_STATUS);
	wr_fifo_bytes >>= WR_FIFO_BYTES_SHFT;

	if (ctrl->xfer.rem_bytes < QSPI_BYTES_PER_WORD) {
		/* Process the last 1-3 bytes */
		wr_size = min(wr_fifo_bytes, ctrl->xfer.rem_bytes);
		ctrl->xfer.rem_bytes -= wr_size;

		byte_buf = xfer_buf;
		while (wr_size--)
			writel(*byte_buf++,
			       ctrl->base + PIO_DATAOUT_1B);
		ctrl->xfer.tx_buf = byte_buf;
	} else {
		/*
		 * Process all the whole words; to keep things simple we'll
		 * just wait for the next interrupt to handle the last 1-3
		 * bytes if we don't have an even number of words.
		 */
		rem_words = ctrl->xfer.rem_bytes / QSPI_BYTES_PER_WORD;
		wr_fifo_words = wr_fifo_bytes / QSPI_BYTES_PER_WORD;

		wr_size = min(rem_words, wr_fifo_words);
		ctrl->xfer.rem_bytes -= wr_size * QSPI_BYTES_PER_WORD;

		word_buf = xfer_buf;
		iowrite32_rep(ctrl->base + PIO_DATAOUT_4B, word_buf, wr_size);
		ctrl->xfer.tx_buf = word_buf + wr_size;

	}

	return IRQ_HANDLED;
}

static irqreturn_t qcom_qspi_irq(int irq, void *dev_id)
{
	u32 int_status;
	struct qcom_qspi *ctrl = dev_id;
	irqreturn_t ret = IRQ_NONE;

	spin_lock(&ctrl->lock);

	int_status = readl(ctrl->base + MSTR_INT_STATUS);
	writel(int_status, ctrl->base + MSTR_INT_STATUS);

	/* Ignore disabled interrupts */
	int_status &= readl(ctrl->base + MSTR_INT_EN);

	/* PIO mode handling */
	if (ctrl->xfer.dir == QSPI_WRITE) {
		if (int_status & WR_FIFO_EMPTY)
			ret = pio_write(ctrl);
	} else {
		if (int_status & RESP_FIFO_RDY)
			ret = pio_read(ctrl);
	}

	if (int_status & QSPI_ERR_IRQS) {
		if (int_status & RESP_FIFO_UNDERRUN)
			dev_err(ctrl->dev, "IRQ error: FIFO underrun\n");
		if (int_status & WR_FIFO_OVERRUN)
			dev_err(ctrl->dev, "IRQ error: FIFO overrun\n");
		if (int_status & HRESP_FROM_NOC_ERR)
			dev_err(ctrl->dev, "IRQ error: NOC response error\n");
		ret = IRQ_HANDLED;
	}

	if (!ctrl->xfer.rem_bytes) {
		writel(0, ctrl->base + MSTR_INT_EN);
		spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
	}

	/* DMA mode handling */
	if (int_status & DMA_CHAIN_DONE) {
		int i;

		writel(0, ctrl->base + MSTR_INT_EN);
		ctrl->xfer.rem_bytes = 0;

		for (i = 0; i < ctrl->n_cmd_desc; i++)
			dma_pool_free(ctrl->dma_cmd_pool, ctrl->virt_cmd_desc[i],
					  ctrl->dma_cmd_desc[i]);
		ctrl->n_cmd_desc = 0;

		ret = IRQ_HANDLED;
		spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev));
	}

	spin_unlock(&ctrl->lock);
	return ret;
}

static int qcom_qspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
{
	/*
	 * If qcom_qspi_can_dma() is going to return false we don't need to
	 * adjust anything.
	 */
	if (op->data.nbytes <= QSPI_MAX_BYTES_FIFO)
		return 0;

	/*
	 * When reading, the transfer needs to be a multiple of 4 bytes so
	 * shrink the transfer if that's not true. The caller will then do a
	 * second transfer to finish things up.
	 */
	if (op->data.dir == SPI_MEM_DATA_IN && (op->data.nbytes & 0x3))
		op->data.nbytes &= ~0x3;

	return 0;
}

static const struct spi_controller_mem_ops qcom_qspi_mem_ops = {
	.adjust_op_size = qcom_qspi_adjust_op_size,
};

static int qcom_qspi_probe(struct platform_device *pdev)
{
	int ret;
	struct device *dev;
	struct spi_controller *host;
	struct qcom_qspi *ctrl;

	dev = &pdev->dev;

	host = devm_spi_alloc_host(dev, sizeof(*ctrl));
	if (!host)
		return -ENOMEM;

	platform_set_drvdata(pdev, host);

	ctrl = spi_controller_get_devdata(host);

	spin_lock_init(&ctrl->lock);
	ctrl->dev = dev;
	ctrl->base = devm_platform_ioremap_resource(pdev, 0);
	if (IS_ERR(ctrl->base))
		return PTR_ERR(ctrl->base);

	ctrl->clks = devm_kcalloc(dev, QSPI_NUM_CLKS,
				  sizeof(*ctrl->clks), GFP_KERNEL);
	if (!ctrl->clks)
		return -ENOMEM;

	ctrl->clks[QSPI_CLK_CORE].id = "core";
	ctrl->clks[QSPI_CLK_IFACE].id = "iface";
	ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks);
	if (ret)
		return ret;

	ctrl->icc_path_cpu_to_qspi = devm_of_icc_get(dev, "qspi-config");
	if (IS_ERR(ctrl->icc_path_cpu_to_qspi))
		return dev_err_probe(dev, PTR_ERR(ctrl->icc_path_cpu_to_qspi),
				     "Failed to get cpu path\n");

	/* Set BW vote for register access */
	ret = icc_set_bw(ctrl->icc_path_cpu_to_qspi, Bps_to_icc(1000),
				Bps_to_icc(1000));
	if (ret) {
		dev_err(ctrl->dev, "%s: ICC BW voting failed for cpu: %d\n",
				__func__, ret);
		return ret;
	}

	ret = icc_disable(ctrl->icc_path_cpu_to_qspi);
	if (ret) {
		dev_err(ctrl->dev, "%s: ICC disable failed for cpu: %d\n",
				__func__, ret);
		return ret;
	}

	ret = platform_get_irq(pdev, 0);
	if (ret < 0)
		return ret;
	ret = devm_request_irq(dev, ret, qcom_qspi_irq, 0, dev_name(dev), ctrl);
	if (ret) {
		dev_err(dev, "Failed to request irq %d\n", ret);
		return ret;
	}

	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
	if (ret)
		return dev_err_probe(dev, ret, "could not set DMA mask\n");

	host->max_speed_hz = 300000000;
	host->max_dma_len = 65536; /* as per HPG */
	host->dma_alignment = QSPI_ALIGN_REQ;
	host->num_chipselect = QSPI_NUM_CS;
	host->bus_num = -1;
	host->dev.of_node = pdev->dev.of_node;
	host->mode_bits = SPI_MODE_0 |
			  SPI_TX_DUAL | SPI_RX_DUAL |
			  SPI_TX_QUAD | SPI_RX_QUAD;
	host->flags = SPI_CONTROLLER_HALF_DUPLEX;
	host->prepare_message = qcom_qspi_prepare_message;
	host->transfer_one = qcom_qspi_transfer_one;
	host->handle_err = qcom_qspi_handle_err;
	if (of_property_present(pdev->dev.of_node, "iommus"))
		host->can_dma = qcom_qspi_can_dma;
	host->auto_runtime_pm = true;
	host->mem_ops = &qcom_qspi_mem_ops;

	ret = devm_pm_opp_set_clkname(&pdev->dev, "core");
	if (ret)
		return ret;
	/* OPP table is optional */
	ret = devm_pm_opp_of_add_table(&pdev->dev);
	if (ret && ret != -ENODEV) {
		dev_err(&pdev->dev, "invalid OPP table in device tree\n");
		return ret;
	}

	ret = qcom_qspi_alloc_dma(ctrl);
	if (ret)
		return ret;

	pm_runtime_use_autosuspend(dev);
	pm_runtime_set_autosuspend_delay(dev, 250);
	pm_runtime_enable(dev);

	ret = spi_register_controller(host);
	if (!ret)
		return 0;

	pm_runtime_disable(dev);

	return ret;
}

static void qcom_qspi_remove(struct platform_device *pdev)
{
	struct spi_controller *host = platform_get_drvdata(pdev);

	/* Unregister _before_ disabling pm_runtime() so we stop transfers */
	spi_unregister_controller(host);

	pm_runtime_disable(&pdev->dev);
}

static int __maybe_unused qcom_qspi_runtime_suspend(struct device *dev)
{
	struct spi_controller *host = dev_get_drvdata(dev);
	struct qcom_qspi *ctrl = spi_controller_get_devdata(host);
	int ret;

	/* Drop the performance state vote */
	dev_pm_opp_set_rate(dev, 0);
	clk_bulk_disable_unprepare(QSPI_NUM_CLKS, ctrl->clks);

	ret = icc_disable(ctrl->icc_path_cpu_to_qspi);
	if (ret) {
		dev_err_ratelimited(ctrl->dev, "%s: ICC disable failed for cpu: %d\n",
			__func__, ret);
		return ret;
	}

	pinctrl_pm_select_sleep_state(dev);

	return 0;
}

static int __maybe_unused qcom_qspi_runtime_resume(struct device *dev)
{
	struct spi_controller *host = dev_get_drvdata(dev);
	struct qcom_qspi *ctrl = spi_controller_get_devdata(host);
	int ret;

	pinctrl_pm_select_default_state(dev);

	ret = icc_enable(ctrl->icc_path_cpu_to_qspi);
	if (ret) {
		dev_err_ratelimited(ctrl->dev, "%s: ICC enable failed for cpu: %d\n",
			__func__, ret);
		return ret;
	}

	ret = clk_bulk_prepare_enable(QSPI_NUM_CLKS, ctrl->clks);
	if (ret)
		return ret;

	return dev_pm_opp_set_rate(dev, ctrl->last_speed * 4);
}

static int __maybe_unused qcom_qspi_suspend(struct device *dev)
{
	struct spi_controller *host = dev_get_drvdata(dev);
	int ret;

	ret = spi_controller_suspend(host);
	if (ret)
		return ret;

	ret = pm_runtime_force_suspend(dev);
	if (ret)
		spi_controller_resume(host);

	return ret;
}

static int __maybe_unused qcom_qspi_resume(struct device *dev)
{
	struct spi_controller *host = dev_get_drvdata(dev);
	int ret;

	ret = pm_runtime_force_resume(dev);
	if (ret)
		return ret;

	ret = spi_controller_resume(host);
	if (ret)
		pm_runtime_force_suspend(dev);

	return ret;
}

static const struct dev_pm_ops qcom_qspi_dev_pm_ops = {
	SET_RUNTIME_PM_OPS(qcom_qspi_runtime_suspend,
			   qcom_qspi_runtime_resume, NULL)
	SET_SYSTEM_SLEEP_PM_OPS(qcom_qspi_suspend, qcom_qspi_resume)
};

static const struct of_device_id qcom_qspi_dt_match[] = {
	{ .compatible = "qcom,qspi-v1", },
	{ }
};
MODULE_DEVICE_TABLE(of, qcom_qspi_dt_match);

static struct platform_driver qcom_qspi_driver = {
	.driver = {
		.name		= "qcom_qspi",
		.pm		= &qcom_qspi_dev_pm_ops,
		.of_match_table = qcom_qspi_dt_match,
	},
	.probe = qcom_qspi_probe,
	.remove = qcom_qspi_remove,
};
module_platform_driver(qcom_qspi_driver);

MODULE_DESCRIPTION("SPI driver for QSPI cores");
MODULE_LICENSE("GPL v2");