| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * STMicroelectronics STM32 USB PHY Controller driver | |
| * | |
| * Copyright (C) 2018 STMicroelectronics | |
| * Author(s): Amelie Delaunay <amelie.delaunay@st.com>. | |
| */ | |
| #include <linux/bitfield.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/io.h> | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/phy/phy.h> | |
| #include <linux/reset.h> | |
| #define STM32_USBPHYC_PLL 0x0 | |
| #define STM32_USBPHYC_MISC 0x8 | |
| #define STM32_USBPHYC_VERSION 0x3F4 | |
| /* STM32_USBPHYC_PLL bit fields */ | |
| #define PLLNDIV GENMASK(6, 0) | |
| #define PLLFRACIN GENMASK(25, 10) | |
| #define PLLEN BIT(26) | |
| #define PLLSTRB BIT(27) | |
| #define PLLSTRBYP BIT(28) | |
| #define PLLFRACCTL BIT(29) | |
| #define PLLDITHEN0 BIT(30) | |
| #define PLLDITHEN1 BIT(31) | |
| /* STM32_USBPHYC_MISC bit fields */ | |
| #define SWITHOST BIT(0) | |
| /* STM32_USBPHYC_VERSION bit fields */ | |
| #define MINREV GENMASK(3, 0) | |
| #define MAJREV GENMASK(7, 4) | |
| static const char * const supplies_names[] = { | |
| "vdda1v1", /* 1V1 */ | |
| "vdda1v8", /* 1V8 */ | |
| }; | |
| #define NUM_SUPPLIES ARRAY_SIZE(supplies_names) | |
| #define PLL_LOCK_TIME_US 100 | |
| #define PLL_PWR_DOWN_TIME_US 5 | |
| #define PLL_FVCO_MHZ 2880 | |
| #define PLL_INFF_MIN_RATE_HZ 19200000 | |
| #define PLL_INFF_MAX_RATE_HZ 38400000 | |
| #define HZ_PER_MHZ 1000000L | |
| struct pll_params { | |
| u8 ndiv; | |
| u16 frac; | |
| }; | |
| struct stm32_usbphyc_phy { | |
| struct phy *phy; | |
| struct stm32_usbphyc *usbphyc; | |
| struct regulator_bulk_data supplies[NUM_SUPPLIES]; | |
| u32 index; | |
| bool active; | |
| }; | |
| struct stm32_usbphyc { | |
| struct device *dev; | |
| void __iomem *base; | |
| struct clk *clk; | |
| struct reset_control *rst; | |
| struct stm32_usbphyc_phy **phys; | |
| int nphys; | |
| int switch_setup; | |
| }; | |
| static inline void stm32_usbphyc_set_bits(void __iomem *reg, u32 bits) | |
| { | |
| writel_relaxed(readl_relaxed(reg) | bits, reg); | |
| } | |
| static inline void stm32_usbphyc_clr_bits(void __iomem *reg, u32 bits) | |
| { | |
| writel_relaxed(readl_relaxed(reg) & ~bits, reg); | |
| } | |
| static void stm32_usbphyc_get_pll_params(u32 clk_rate, | |
| struct pll_params *pll_params) | |
| { | |
| unsigned long long fvco, ndiv, frac; | |
| /* _ | |
| * | FVCO = INFF*2*(NDIV + FRACT/2^16) when DITHER_DISABLE[1] = 1 | |
| * | FVCO = 2880MHz | |
| * < | |
| * | NDIV = integer part of input bits to set the LDF | |
| * |_FRACT = fractional part of input bits to set the LDF | |
| * => PLLNDIV = integer part of (FVCO / (INFF*2)) | |
| * => PLLFRACIN = fractional part of(FVCO / INFF*2) * 2^16 | |
| * <=> PLLFRACIN = ((FVCO / (INFF*2)) - PLLNDIV) * 2^16 | |
| */ | |
| fvco = (unsigned long long)PLL_FVCO_MHZ * HZ_PER_MHZ; | |
| ndiv = fvco; | |
| do_div(ndiv, (clk_rate * 2)); | |
| pll_params->ndiv = (u8)ndiv; | |
| frac = fvco * (1 << 16); | |
| do_div(frac, (clk_rate * 2)); | |
| frac = frac - (ndiv * (1 << 16)); | |
| pll_params->frac = (u16)frac; | |
| } | |
| static int stm32_usbphyc_pll_init(struct stm32_usbphyc *usbphyc) | |
| { | |
| struct pll_params pll_params; | |
| u32 clk_rate = clk_get_rate(usbphyc->clk); | |
| u32 ndiv, frac; | |
| u32 usbphyc_pll; | |
| if ((clk_rate < PLL_INFF_MIN_RATE_HZ) || | |
| (clk_rate > PLL_INFF_MAX_RATE_HZ)) { | |
| dev_err(usbphyc->dev, "input clk freq (%dHz) out of range\n", | |
| clk_rate); | |
| return -EINVAL; | |
| } | |
| stm32_usbphyc_get_pll_params(clk_rate, &pll_params); | |
| ndiv = FIELD_PREP(PLLNDIV, pll_params.ndiv); | |
| frac = FIELD_PREP(PLLFRACIN, pll_params.frac); | |
| usbphyc_pll = PLLDITHEN1 | PLLDITHEN0 | PLLSTRBYP | ndiv; | |
| if (pll_params.frac) | |
| usbphyc_pll |= PLLFRACCTL | frac; | |
| writel_relaxed(usbphyc_pll, usbphyc->base + STM32_USBPHYC_PLL); | |
| dev_dbg(usbphyc->dev, "input clk freq=%dHz, ndiv=%lu, frac=%lu\n", | |
| clk_rate, FIELD_GET(PLLNDIV, usbphyc_pll), | |
| FIELD_GET(PLLFRACIN, usbphyc_pll)); | |
| return 0; | |
| } | |
| static bool stm32_usbphyc_has_one_phy_active(struct stm32_usbphyc *usbphyc) | |
| { | |
| int i; | |
| for (i = 0; i < usbphyc->nphys; i++) | |
| if (usbphyc->phys[i]->active) | |
| return true; | |
| return false; | |
| } | |
| static int stm32_usbphyc_pll_enable(struct stm32_usbphyc *usbphyc) | |
| { | |
| void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; | |
| bool pllen = (readl_relaxed(pll_reg) & PLLEN); | |
| int ret; | |
| /* Check if one phy port has already configured the pll */ | |
| if (pllen && stm32_usbphyc_has_one_phy_active(usbphyc)) | |
| return 0; | |
| if (pllen) { | |
| stm32_usbphyc_clr_bits(pll_reg, PLLEN); | |
| /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ | |
| udelay(PLL_PWR_DOWN_TIME_US); | |
| } | |
| ret = stm32_usbphyc_pll_init(usbphyc); | |
| if (ret) | |
| return ret; | |
| stm32_usbphyc_set_bits(pll_reg, PLLEN); | |
| /* Wait for maximum lock time */ | |
| udelay(PLL_LOCK_TIME_US); | |
| if (!(readl_relaxed(pll_reg) & PLLEN)) { | |
| dev_err(usbphyc->dev, "PLLEN not set\n"); | |
| return -EIO; | |
| } | |
| return 0; | |
| } | |
| static int stm32_usbphyc_pll_disable(struct stm32_usbphyc *usbphyc) | |
| { | |
| void __iomem *pll_reg = usbphyc->base + STM32_USBPHYC_PLL; | |
| /* Check if other phy port active */ | |
| if (stm32_usbphyc_has_one_phy_active(usbphyc)) | |
| return 0; | |
| stm32_usbphyc_clr_bits(pll_reg, PLLEN); | |
| /* Wait for minimum width of powerdown pulse (ENABLE = Low) */ | |
| udelay(PLL_PWR_DOWN_TIME_US); | |
| if (readl_relaxed(pll_reg) & PLLEN) { | |
| dev_err(usbphyc->dev, "PLL not reset\n"); | |
| return -EIO; | |
| } | |
| return 0; | |
| } | |
| static int stm32_usbphyc_phy_init(struct phy *phy) | |
| { | |
| struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); | |
| struct stm32_usbphyc *usbphyc = usbphyc_phy->usbphyc; | |
| int ret; | |
| ret = stm32_usbphyc_pll_enable(usbphyc); | |
| if (ret) | |
| return ret; | |
| usbphyc_phy->active = true; | |
| return 0; | |
| } | |
| static int stm32_usbphyc_phy_exit(struct phy *phy) | |
| { | |
| struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); | |
| struct stm32_usbphyc *usbphyc = usbphyc_phy->usbphyc; | |
| usbphyc_phy->active = false; | |
| return stm32_usbphyc_pll_disable(usbphyc); | |
| } | |
| static int stm32_usbphyc_phy_power_on(struct phy *phy) | |
| { | |
| struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); | |
| return regulator_bulk_enable(NUM_SUPPLIES, usbphyc_phy->supplies); | |
| } | |
| static int stm32_usbphyc_phy_power_off(struct phy *phy) | |
| { | |
| struct stm32_usbphyc_phy *usbphyc_phy = phy_get_drvdata(phy); | |
| return regulator_bulk_disable(NUM_SUPPLIES, usbphyc_phy->supplies); | |
| } | |
| static const struct phy_ops stm32_usbphyc_phy_ops = { | |
| .init = stm32_usbphyc_phy_init, | |
| .exit = stm32_usbphyc_phy_exit, | |
| .power_on = stm32_usbphyc_phy_power_on, | |
| .power_off = stm32_usbphyc_phy_power_off, | |
| .owner = THIS_MODULE, | |
| }; | |
| static void stm32_usbphyc_switch_setup(struct stm32_usbphyc *usbphyc, | |
| u32 utmi_switch) | |
| { | |
| if (!utmi_switch) | |
| stm32_usbphyc_clr_bits(usbphyc->base + STM32_USBPHYC_MISC, | |
| SWITHOST); | |
| else | |
| stm32_usbphyc_set_bits(usbphyc->base + STM32_USBPHYC_MISC, | |
| SWITHOST); | |
| usbphyc->switch_setup = utmi_switch; | |
| } | |
| static struct phy *stm32_usbphyc_of_xlate(struct device *dev, | |
| struct of_phandle_args *args) | |
| { | |
| struct stm32_usbphyc *usbphyc = dev_get_drvdata(dev); | |
| struct stm32_usbphyc_phy *usbphyc_phy = NULL; | |
| struct device_node *phynode = args->np; | |
| int port = 0; | |
| for (port = 0; port < usbphyc->nphys; port++) { | |
| if (phynode == usbphyc->phys[port]->phy->dev.of_node) { | |
| usbphyc_phy = usbphyc->phys[port]; | |
| break; | |
| } | |
| } | |
| if (!usbphyc_phy) { | |
| dev_err(dev, "failed to find phy\n"); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| if (((usbphyc_phy->index == 0) && (args->args_count != 0)) || | |
| ((usbphyc_phy->index == 1) && (args->args_count != 1))) { | |
| dev_err(dev, "invalid number of cells for phy port%d\n", | |
| usbphyc_phy->index); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| /* Configure the UTMI switch for PHY port#2 */ | |
| if (usbphyc_phy->index == 1) { | |
| if (usbphyc->switch_setup < 0) { | |
| stm32_usbphyc_switch_setup(usbphyc, args->args[0]); | |
| } else { | |
| if (args->args[0] != usbphyc->switch_setup) { | |
| dev_err(dev, "phy port1 already used\n"); | |
| return ERR_PTR(-EBUSY); | |
| } | |
| } | |
| } | |
| return usbphyc_phy->phy; | |
| } | |
| static int stm32_usbphyc_probe(struct platform_device *pdev) | |
| { | |
| struct stm32_usbphyc *usbphyc; | |
| struct device *dev = &pdev->dev; | |
| struct device_node *child, *np = dev->of_node; | |
| struct resource *res; | |
| struct phy_provider *phy_provider; | |
| u32 version; | |
| int ret, port = 0; | |
| usbphyc = devm_kzalloc(dev, sizeof(*usbphyc), GFP_KERNEL); | |
| if (!usbphyc) | |
| return -ENOMEM; | |
| usbphyc->dev = dev; | |
| dev_set_drvdata(dev, usbphyc); | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| usbphyc->base = devm_ioremap_resource(dev, res); | |
| if (IS_ERR(usbphyc->base)) | |
| return PTR_ERR(usbphyc->base); | |
| usbphyc->clk = devm_clk_get(dev, NULL); | |
| if (IS_ERR(usbphyc->clk)) { | |
| ret = PTR_ERR(usbphyc->clk); | |
| dev_err(dev, "clk get failed: %d\n", ret); | |
| return ret; | |
| } | |
| ret = clk_prepare_enable(usbphyc->clk); | |
| if (ret) { | |
| dev_err(dev, "clk enable failed: %d\n", ret); | |
| return ret; | |
| } | |
| usbphyc->rst = devm_reset_control_get(dev, NULL); | |
| if (!IS_ERR(usbphyc->rst)) { | |
| reset_control_assert(usbphyc->rst); | |
| udelay(2); | |
| reset_control_deassert(usbphyc->rst); | |
| } | |
| usbphyc->switch_setup = -EINVAL; | |
| usbphyc->nphys = of_get_child_count(np); | |
| usbphyc->phys = devm_kcalloc(dev, usbphyc->nphys, | |
| sizeof(*usbphyc->phys), GFP_KERNEL); | |
| if (!usbphyc->phys) { | |
| ret = -ENOMEM; | |
| goto clk_disable; | |
| } | |
| for_each_child_of_node(np, child) { | |
| struct stm32_usbphyc_phy *usbphyc_phy; | |
| struct phy *phy; | |
| u32 index; | |
| int i; | |
| phy = devm_phy_create(dev, child, &stm32_usbphyc_phy_ops); | |
| if (IS_ERR(phy)) { | |
| ret = PTR_ERR(phy); | |
| if (ret != -EPROBE_DEFER) | |
| dev_err(dev, "failed to create phy%d: %d\n", | |
| port, ret); | |
| goto put_child; | |
| } | |
| usbphyc_phy = devm_kzalloc(dev, sizeof(*usbphyc_phy), | |
| GFP_KERNEL); | |
| if (!usbphyc_phy) { | |
| ret = -ENOMEM; | |
| goto put_child; | |
| } | |
| for (i = 0; i < NUM_SUPPLIES; i++) | |
| usbphyc_phy->supplies[i].supply = supplies_names[i]; | |
| ret = devm_regulator_bulk_get(&phy->dev, NUM_SUPPLIES, | |
| usbphyc_phy->supplies); | |
| if (ret) { | |
| if (ret != -EPROBE_DEFER) | |
| dev_err(&phy->dev, | |
| "failed to get regulators: %d\n", ret); | |
| goto put_child; | |
| } | |
| ret = of_property_read_u32(child, "reg", &index); | |
| if (ret || index > usbphyc->nphys) { | |
| dev_err(&phy->dev, "invalid reg property: %d\n", ret); | |
| goto put_child; | |
| } | |
| usbphyc->phys[port] = usbphyc_phy; | |
| phy_set_bus_width(phy, 8); | |
| phy_set_drvdata(phy, usbphyc_phy); | |
| usbphyc->phys[port]->phy = phy; | |
| usbphyc->phys[port]->usbphyc = usbphyc; | |
| usbphyc->phys[port]->index = index; | |
| usbphyc->phys[port]->active = false; | |
| port++; | |
| } | |
| phy_provider = devm_of_phy_provider_register(dev, | |
| stm32_usbphyc_of_xlate); | |
| if (IS_ERR(phy_provider)) { | |
| ret = PTR_ERR(phy_provider); | |
| dev_err(dev, "failed to register phy provider: %d\n", ret); | |
| goto clk_disable; | |
| } | |
| version = readl_relaxed(usbphyc->base + STM32_USBPHYC_VERSION); | |
| dev_info(dev, "registered rev:%lu.%lu\n", | |
| FIELD_GET(MAJREV, version), FIELD_GET(MINREV, version)); | |
| return 0; | |
| put_child: | |
| of_node_put(child); | |
| clk_disable: | |
| clk_disable_unprepare(usbphyc->clk); | |
| return ret; | |
| } | |
| static int stm32_usbphyc_remove(struct platform_device *pdev) | |
| { | |
| struct stm32_usbphyc *usbphyc = dev_get_drvdata(&pdev->dev); | |
| clk_disable_unprepare(usbphyc->clk); | |
| return 0; | |
| } | |
| static const struct of_device_id stm32_usbphyc_of_match[] = { | |
| { .compatible = "st,stm32mp1-usbphyc", }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, stm32_usbphyc_of_match); | |
| static struct platform_driver stm32_usbphyc_driver = { | |
| .probe = stm32_usbphyc_probe, | |
| .remove = stm32_usbphyc_remove, | |
| .driver = { | |
| .of_match_table = stm32_usbphyc_of_match, | |
| .name = "stm32-usbphyc", | |
| } | |
| }; | |
| module_platform_driver(stm32_usbphyc_driver); | |
| MODULE_DESCRIPTION("STMicroelectronics STM32 USBPHYC driver"); | |
| MODULE_AUTHOR("Amelie Delaunay <amelie.delaunay@st.com>"); | |
| MODULE_LICENSE("GPL v2"); |