| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2014 MediaTek Inc. |
| * Author: Xudong Chen <xudong.chen@mediatek.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/completion.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/err.h> |
| #include <linux/errno.h> |
| #include <linux/i2c.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/iopoll.h> |
| #include <linux/kernel.h> |
| #include <linux/mm.h> |
| #include <linux/module.h> |
| #include <linux/of_address.h> |
| #include <linux/of_device.h> |
| #include <linux/of_irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/scatterlist.h> |
| #include <linux/sched.h> |
| #include <linux/slab.h> |
| |
| #define I2C_RS_TRANSFER (1 << 4) |
| #define I2C_ARB_LOST (1 << 3) |
| #define I2C_HS_NACKERR (1 << 2) |
| #define I2C_ACKERR (1 << 1) |
| #define I2C_TRANSAC_COMP (1 << 0) |
| #define I2C_TRANSAC_START (1 << 0) |
| #define I2C_RS_MUL_CNFG (1 << 15) |
| #define I2C_RS_MUL_TRIG (1 << 14) |
| #define I2C_DCM_DISABLE 0x0000 |
| #define I2C_IO_CONFIG_OPEN_DRAIN 0x0003 |
| #define I2C_IO_CONFIG_PUSH_PULL 0x0000 |
| #define I2C_SOFT_RST 0x0001 |
| #define I2C_HANDSHAKE_RST 0x0020 |
| #define I2C_FIFO_ADDR_CLR 0x0001 |
| #define I2C_DELAY_LEN 0x0002 |
| #define I2C_ST_START_CON 0x8001 |
| #define I2C_FS_START_CON 0x1800 |
| #define I2C_TIME_CLR_VALUE 0x0000 |
| #define I2C_TIME_DEFAULT_VALUE 0x0003 |
| #define I2C_WRRD_TRANAC_VALUE 0x0002 |
| #define I2C_RD_TRANAC_VALUE 0x0001 |
| #define I2C_SCL_MIS_COMP_VALUE 0x0000 |
| #define I2C_CHN_CLR_FLAG 0x0000 |
| #define I2C_RELIABILITY 0x0010 |
| #define I2C_DMAACK_ENABLE 0x0008 |
| |
| #define I2C_DMA_CON_TX 0x0000 |
| #define I2C_DMA_CON_RX 0x0001 |
| #define I2C_DMA_ASYNC_MODE 0x0004 |
| #define I2C_DMA_SKIP_CONFIG 0x0010 |
| #define I2C_DMA_DIR_CHANGE 0x0200 |
| #define I2C_DMA_START_EN 0x0001 |
| #define I2C_DMA_INT_FLAG_NONE 0x0000 |
| #define I2C_DMA_CLR_FLAG 0x0000 |
| #define I2C_DMA_WARM_RST 0x0001 |
| #define I2C_DMA_HARD_RST 0x0002 |
| #define I2C_DMA_HANDSHAKE_RST 0x0004 |
| |
| #define MAX_SAMPLE_CNT_DIV 8 |
| #define MAX_STEP_CNT_DIV 64 |
| #define MAX_CLOCK_DIV_8BITS 256 |
| #define MAX_CLOCK_DIV_5BITS 32 |
| #define MAX_HS_STEP_CNT_DIV 8 |
| #define I2C_STANDARD_MODE_BUFFER (1000 / 3) |
| #define I2C_FAST_MODE_BUFFER (300 / 3) |
| #define I2C_FAST_MODE_PLUS_BUFFER (20 / 3) |
| |
| #define I2C_CONTROL_RS (0x1 << 1) |
| #define I2C_CONTROL_DMA_EN (0x1 << 2) |
| #define I2C_CONTROL_CLK_EXT_EN (0x1 << 3) |
| #define I2C_CONTROL_DIR_CHANGE (0x1 << 4) |
| #define I2C_CONTROL_ACKERR_DET_EN (0x1 << 5) |
| #define I2C_CONTROL_TRANSFER_LEN_CHANGE (0x1 << 6) |
| #define I2C_CONTROL_DMAACK_EN (0x1 << 8) |
| #define I2C_CONTROL_ASYNC_MODE (0x1 << 9) |
| #define I2C_CONTROL_WRAPPER (0x1 << 0) |
| |
| #define I2C_DRV_NAME "i2c-mt65xx" |
| |
| /** |
| * enum i2c_mt65xx_clks - Clocks enumeration for MT65XX I2C |
| * |
| * @I2C_MT65XX_CLK_MAIN: main clock for i2c bus |
| * @I2C_MT65XX_CLK_DMA: DMA clock for i2c via DMA |
| * @I2C_MT65XX_CLK_PMIC: PMIC clock for i2c from PMIC |
| * @I2C_MT65XX_CLK_ARB: Arbitrator clock for i2c |
| * @I2C_MT65XX_CLK_MAX: Number of supported clocks |
| */ |
| enum i2c_mt65xx_clks { |
| I2C_MT65XX_CLK_MAIN = 0, |
| I2C_MT65XX_CLK_DMA, |
| I2C_MT65XX_CLK_PMIC, |
| I2C_MT65XX_CLK_ARB, |
| I2C_MT65XX_CLK_MAX |
| }; |
| |
| static const char * const i2c_mt65xx_clk_ids[I2C_MT65XX_CLK_MAX] = { |
| "main", "dma", "pmic", "arb" |
| }; |
| |
| enum DMA_REGS_OFFSET { |
| OFFSET_INT_FLAG = 0x0, |
| OFFSET_INT_EN = 0x04, |
| OFFSET_EN = 0x08, |
| OFFSET_RST = 0x0c, |
| OFFSET_CON = 0x18, |
| OFFSET_TX_MEM_ADDR = 0x1c, |
| OFFSET_RX_MEM_ADDR = 0x20, |
| OFFSET_TX_LEN = 0x24, |
| OFFSET_RX_LEN = 0x28, |
| OFFSET_TX_4G_MODE = 0x54, |
| OFFSET_RX_4G_MODE = 0x58, |
| }; |
| |
| enum i2c_trans_st_rs { |
| I2C_TRANS_STOP = 0, |
| I2C_TRANS_REPEATED_START, |
| }; |
| |
| enum mtk_trans_op { |
| I2C_MASTER_WR = 1, |
| I2C_MASTER_RD, |
| I2C_MASTER_WRRD, |
| }; |
| |
| enum I2C_REGS_OFFSET { |
| OFFSET_DATA_PORT, |
| OFFSET_SLAVE_ADDR, |
| OFFSET_INTR_MASK, |
| OFFSET_INTR_STAT, |
| OFFSET_CONTROL, |
| OFFSET_TRANSFER_LEN, |
| OFFSET_TRANSAC_LEN, |
| OFFSET_DELAY_LEN, |
| OFFSET_TIMING, |
| OFFSET_START, |
| OFFSET_EXT_CONF, |
| OFFSET_FIFO_STAT, |
| OFFSET_FIFO_THRESH, |
| OFFSET_FIFO_ADDR_CLR, |
| OFFSET_IO_CONFIG, |
| OFFSET_RSV_DEBUG, |
| OFFSET_HS, |
| OFFSET_SOFTRESET, |
| OFFSET_DCM_EN, |
| OFFSET_MULTI_DMA, |
| OFFSET_PATH_DIR, |
| OFFSET_DEBUGSTAT, |
| OFFSET_DEBUGCTRL, |
| OFFSET_TRANSFER_LEN_AUX, |
| OFFSET_CLOCK_DIV, |
| OFFSET_LTIMING, |
| OFFSET_SCL_HIGH_LOW_RATIO, |
| OFFSET_HS_SCL_HIGH_LOW_RATIO, |
| OFFSET_SCL_MIS_COMP_POINT, |
| OFFSET_STA_STO_AC_TIMING, |
| OFFSET_HS_STA_STO_AC_TIMING, |
| OFFSET_SDA_TIMING, |
| }; |
| |
| static const u16 mt_i2c_regs_v1[] = { |
| [OFFSET_DATA_PORT] = 0x0, |
| [OFFSET_SLAVE_ADDR] = 0x4, |
| [OFFSET_INTR_MASK] = 0x8, |
| [OFFSET_INTR_STAT] = 0xc, |
| [OFFSET_CONTROL] = 0x10, |
| [OFFSET_TRANSFER_LEN] = 0x14, |
| [OFFSET_TRANSAC_LEN] = 0x18, |
| [OFFSET_DELAY_LEN] = 0x1c, |
| [OFFSET_TIMING] = 0x20, |
| [OFFSET_START] = 0x24, |
| [OFFSET_EXT_CONF] = 0x28, |
| [OFFSET_FIFO_STAT] = 0x30, |
| [OFFSET_FIFO_THRESH] = 0x34, |
| [OFFSET_FIFO_ADDR_CLR] = 0x38, |
| [OFFSET_IO_CONFIG] = 0x40, |
| [OFFSET_RSV_DEBUG] = 0x44, |
| [OFFSET_HS] = 0x48, |
| [OFFSET_SOFTRESET] = 0x50, |
| [OFFSET_DCM_EN] = 0x54, |
| [OFFSET_PATH_DIR] = 0x60, |
| [OFFSET_DEBUGSTAT] = 0x64, |
| [OFFSET_DEBUGCTRL] = 0x68, |
| [OFFSET_TRANSFER_LEN_AUX] = 0x6c, |
| [OFFSET_CLOCK_DIV] = 0x70, |
| [OFFSET_SCL_HIGH_LOW_RATIO] = 0x74, |
| [OFFSET_HS_SCL_HIGH_LOW_RATIO] = 0x78, |
| [OFFSET_SCL_MIS_COMP_POINT] = 0x7C, |
| [OFFSET_STA_STO_AC_TIMING] = 0x80, |
| [OFFSET_HS_STA_STO_AC_TIMING] = 0x84, |
| [OFFSET_SDA_TIMING] = 0x88, |
| }; |
| |
| static const u16 mt_i2c_regs_v2[] = { |
| [OFFSET_DATA_PORT] = 0x0, |
| [OFFSET_SLAVE_ADDR] = 0x4, |
| [OFFSET_INTR_MASK] = 0x8, |
| [OFFSET_INTR_STAT] = 0xc, |
| [OFFSET_CONTROL] = 0x10, |
| [OFFSET_TRANSFER_LEN] = 0x14, |
| [OFFSET_TRANSAC_LEN] = 0x18, |
| [OFFSET_DELAY_LEN] = 0x1c, |
| [OFFSET_TIMING] = 0x20, |
| [OFFSET_START] = 0x24, |
| [OFFSET_EXT_CONF] = 0x28, |
| [OFFSET_LTIMING] = 0x2c, |
| [OFFSET_HS] = 0x30, |
| [OFFSET_IO_CONFIG] = 0x34, |
| [OFFSET_FIFO_ADDR_CLR] = 0x38, |
| [OFFSET_SDA_TIMING] = 0x3c, |
| [OFFSET_TRANSFER_LEN_AUX] = 0x44, |
| [OFFSET_CLOCK_DIV] = 0x48, |
| [OFFSET_SOFTRESET] = 0x50, |
| [OFFSET_MULTI_DMA] = 0x8c, |
| [OFFSET_SCL_MIS_COMP_POINT] = 0x90, |
| [OFFSET_DEBUGSTAT] = 0xe4, |
| [OFFSET_DEBUGCTRL] = 0xe8, |
| [OFFSET_FIFO_STAT] = 0xf4, |
| [OFFSET_FIFO_THRESH] = 0xf8, |
| [OFFSET_DCM_EN] = 0xf88, |
| }; |
| |
| static const u16 mt_i2c_regs_v3[] = { |
| [OFFSET_DATA_PORT] = 0x0, |
| [OFFSET_INTR_MASK] = 0x8, |
| [OFFSET_INTR_STAT] = 0xc, |
| [OFFSET_CONTROL] = 0x10, |
| [OFFSET_TRANSFER_LEN] = 0x14, |
| [OFFSET_TRANSAC_LEN] = 0x18, |
| [OFFSET_DELAY_LEN] = 0x1c, |
| [OFFSET_TIMING] = 0x20, |
| [OFFSET_START] = 0x24, |
| [OFFSET_EXT_CONF] = 0x28, |
| [OFFSET_LTIMING] = 0x2c, |
| [OFFSET_HS] = 0x30, |
| [OFFSET_IO_CONFIG] = 0x34, |
| [OFFSET_FIFO_ADDR_CLR] = 0x38, |
| [OFFSET_SDA_TIMING] = 0x3c, |
| [OFFSET_TRANSFER_LEN_AUX] = 0x44, |
| [OFFSET_CLOCK_DIV] = 0x48, |
| [OFFSET_SOFTRESET] = 0x50, |
| [OFFSET_MULTI_DMA] = 0x8c, |
| [OFFSET_SCL_MIS_COMP_POINT] = 0x90, |
| [OFFSET_SLAVE_ADDR] = 0x94, |
| [OFFSET_DEBUGSTAT] = 0xe4, |
| [OFFSET_DEBUGCTRL] = 0xe8, |
| [OFFSET_FIFO_STAT] = 0xf4, |
| [OFFSET_FIFO_THRESH] = 0xf8, |
| [OFFSET_DCM_EN] = 0xf88, |
| }; |
| |
| struct mtk_i2c_compatible { |
| const struct i2c_adapter_quirks *quirks; |
| const u16 *regs; |
| unsigned char pmic_i2c: 1; |
| unsigned char dcm: 1; |
| unsigned char auto_restart: 1; |
| unsigned char aux_len_reg: 1; |
| unsigned char timing_adjust: 1; |
| unsigned char dma_sync: 1; |
| unsigned char ltiming_adjust: 1; |
| unsigned char apdma_sync: 1; |
| unsigned char max_dma_support; |
| }; |
| |
| struct mtk_i2c_ac_timing { |
| u16 htiming; |
| u16 ltiming; |
| u16 hs; |
| u16 ext; |
| u16 inter_clk_div; |
| u16 scl_hl_ratio; |
| u16 hs_scl_hl_ratio; |
| u16 sta_stop; |
| u16 hs_sta_stop; |
| u16 sda_timing; |
| }; |
| |
| struct mtk_i2c { |
| struct i2c_adapter adap; /* i2c host adapter */ |
| struct device *dev; |
| struct completion msg_complete; |
| struct i2c_timings timing_info; |
| |
| /* set in i2c probe */ |
| void __iomem *base; /* i2c base addr */ |
| void __iomem *pdmabase; /* dma base address*/ |
| struct clk_bulk_data clocks[I2C_MT65XX_CLK_MAX]; /* clocks for i2c */ |
| bool have_pmic; /* can use i2c pins from PMIC */ |
| bool use_push_pull; /* IO config push-pull mode */ |
| |
| u16 irq_stat; /* interrupt status */ |
| unsigned int clk_src_div; |
| unsigned int speed_hz; /* The speed in transfer */ |
| enum mtk_trans_op op; |
| u16 timing_reg; |
| u16 high_speed_reg; |
| u16 ltiming_reg; |
| unsigned char auto_restart; |
| bool ignore_restart_irq; |
| struct mtk_i2c_ac_timing ac_timing; |
| const struct mtk_i2c_compatible *dev_comp; |
| }; |
| |
| /** |
| * struct i2c_spec_values: |
| * @min_low_ns: min LOW period of the SCL clock |
| * @min_su_sta_ns: min set-up time for a repeated START condition |
| * @max_hd_dat_ns: max data hold time |
| * @min_su_dat_ns: min data set-up time |
| */ |
| struct i2c_spec_values { |
| unsigned int min_low_ns; |
| unsigned int min_su_sta_ns; |
| unsigned int max_hd_dat_ns; |
| unsigned int min_su_dat_ns; |
| }; |
| |
| static const struct i2c_spec_values standard_mode_spec = { |
| .min_low_ns = 4700 + I2C_STANDARD_MODE_BUFFER, |
| .min_su_sta_ns = 4700 + I2C_STANDARD_MODE_BUFFER, |
| .max_hd_dat_ns = 3450 - I2C_STANDARD_MODE_BUFFER, |
| .min_su_dat_ns = 250 + I2C_STANDARD_MODE_BUFFER, |
| }; |
| |
| static const struct i2c_spec_values fast_mode_spec = { |
| .min_low_ns = 1300 + I2C_FAST_MODE_BUFFER, |
| .min_su_sta_ns = 600 + I2C_FAST_MODE_BUFFER, |
| .max_hd_dat_ns = 900 - I2C_FAST_MODE_BUFFER, |
| .min_su_dat_ns = 100 + I2C_FAST_MODE_BUFFER, |
| }; |
| |
| static const struct i2c_spec_values fast_mode_plus_spec = { |
| .min_low_ns = 500 + I2C_FAST_MODE_PLUS_BUFFER, |
| .min_su_sta_ns = 260 + I2C_FAST_MODE_PLUS_BUFFER, |
| .max_hd_dat_ns = 400 - I2C_FAST_MODE_PLUS_BUFFER, |
| .min_su_dat_ns = 50 + I2C_FAST_MODE_PLUS_BUFFER, |
| }; |
| |
| static const struct i2c_adapter_quirks mt6577_i2c_quirks = { |
| .flags = I2C_AQ_COMB_WRITE_THEN_READ, |
| .max_num_msgs = 1, |
| .max_write_len = 255, |
| .max_read_len = 255, |
| .max_comb_1st_msg_len = 255, |
| .max_comb_2nd_msg_len = 31, |
| }; |
| |
| static const struct i2c_adapter_quirks mt7622_i2c_quirks = { |
| .max_num_msgs = 255, |
| }; |
| |
| static const struct i2c_adapter_quirks mt8183_i2c_quirks = { |
| .flags = I2C_AQ_NO_ZERO_LEN, |
| }; |
| |
| static const struct mtk_i2c_compatible mt2712_compat = { |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 0, |
| .dcm = 1, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 0, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 33, |
| }; |
| |
| static const struct mtk_i2c_compatible mt6577_compat = { |
| .quirks = &mt6577_i2c_quirks, |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 0, |
| .dcm = 1, |
| .auto_restart = 0, |
| .aux_len_reg = 0, |
| .timing_adjust = 0, |
| .dma_sync = 0, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 32, |
| }; |
| |
| static const struct mtk_i2c_compatible mt6589_compat = { |
| .quirks = &mt6577_i2c_quirks, |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 1, |
| .dcm = 0, |
| .auto_restart = 0, |
| .aux_len_reg = 0, |
| .timing_adjust = 0, |
| .dma_sync = 0, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 32, |
| }; |
| |
| static const struct mtk_i2c_compatible mt7622_compat = { |
| .quirks = &mt7622_i2c_quirks, |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 0, |
| .dcm = 1, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 0, |
| .dma_sync = 0, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 32, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8168_compat = { |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 0, |
| .dcm = 1, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 1, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 33, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8173_compat = { |
| .regs = mt_i2c_regs_v1, |
| .pmic_i2c = 0, |
| .dcm = 1, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 0, |
| .dma_sync = 0, |
| .ltiming_adjust = 0, |
| .apdma_sync = 0, |
| .max_dma_support = 33, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8183_compat = { |
| .quirks = &mt8183_i2c_quirks, |
| .regs = mt_i2c_regs_v2, |
| .pmic_i2c = 0, |
| .dcm = 0, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 1, |
| .ltiming_adjust = 1, |
| .apdma_sync = 0, |
| .max_dma_support = 33, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8186_compat = { |
| .regs = mt_i2c_regs_v2, |
| .pmic_i2c = 0, |
| .dcm = 0, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 0, |
| .ltiming_adjust = 1, |
| .apdma_sync = 0, |
| .max_dma_support = 36, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8188_compat = { |
| .regs = mt_i2c_regs_v3, |
| .pmic_i2c = 0, |
| .dcm = 0, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 0, |
| .ltiming_adjust = 1, |
| .apdma_sync = 1, |
| .max_dma_support = 36, |
| }; |
| |
| static const struct mtk_i2c_compatible mt8192_compat = { |
| .quirks = &mt8183_i2c_quirks, |
| .regs = mt_i2c_regs_v2, |
| .pmic_i2c = 0, |
| .dcm = 0, |
| .auto_restart = 1, |
| .aux_len_reg = 1, |
| .timing_adjust = 1, |
| .dma_sync = 1, |
| .ltiming_adjust = 1, |
| .apdma_sync = 1, |
| .max_dma_support = 36, |
| }; |
| |
| static const struct of_device_id mtk_i2c_of_match[] = { |
| { .compatible = "mediatek,mt2712-i2c", .data = &mt2712_compat }, |
| { .compatible = "mediatek,mt6577-i2c", .data = &mt6577_compat }, |
| { .compatible = "mediatek,mt6589-i2c", .data = &mt6589_compat }, |
| { .compatible = "mediatek,mt7622-i2c", .data = &mt7622_compat }, |
| { .compatible = "mediatek,mt8168-i2c", .data = &mt8168_compat }, |
| { .compatible = "mediatek,mt8173-i2c", .data = &mt8173_compat }, |
| { .compatible = "mediatek,mt8183-i2c", .data = &mt8183_compat }, |
| { .compatible = "mediatek,mt8186-i2c", .data = &mt8186_compat }, |
| { .compatible = "mediatek,mt8188-i2c", .data = &mt8188_compat }, |
| { .compatible = "mediatek,mt8192-i2c", .data = &mt8192_compat }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, mtk_i2c_of_match); |
| |
| static u16 mtk_i2c_readw(struct mtk_i2c *i2c, enum I2C_REGS_OFFSET reg) |
| { |
| return readw(i2c->base + i2c->dev_comp->regs[reg]); |
| } |
| |
| static void mtk_i2c_writew(struct mtk_i2c *i2c, u16 val, |
| enum I2C_REGS_OFFSET reg) |
| { |
| writew(val, i2c->base + i2c->dev_comp->regs[reg]); |
| } |
| |
| static void mtk_i2c_init_hw(struct mtk_i2c *i2c) |
| { |
| u16 control_reg; |
| u16 intr_stat_reg; |
| u16 ext_conf_val; |
| |
| mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_START); |
| intr_stat_reg = mtk_i2c_readw(i2c, OFFSET_INTR_STAT); |
| mtk_i2c_writew(i2c, intr_stat_reg, OFFSET_INTR_STAT); |
| |
| if (i2c->dev_comp->apdma_sync) { |
| writel(I2C_DMA_WARM_RST, i2c->pdmabase + OFFSET_RST); |
| udelay(10); |
| writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST); |
| udelay(10); |
| writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_HARD_RST, |
| i2c->pdmabase + OFFSET_RST); |
| mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST | I2C_SOFT_RST, |
| OFFSET_SOFTRESET); |
| udelay(10); |
| writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST); |
| mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET); |
| } else { |
| writel(I2C_DMA_HARD_RST, i2c->pdmabase + OFFSET_RST); |
| udelay(50); |
| writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST); |
| mtk_i2c_writew(i2c, I2C_SOFT_RST, OFFSET_SOFTRESET); |
| } |
| |
| /* Set ioconfig */ |
| if (i2c->use_push_pull) |
| mtk_i2c_writew(i2c, I2C_IO_CONFIG_PUSH_PULL, OFFSET_IO_CONFIG); |
| else |
| mtk_i2c_writew(i2c, I2C_IO_CONFIG_OPEN_DRAIN, OFFSET_IO_CONFIG); |
| |
| if (i2c->dev_comp->dcm) |
| mtk_i2c_writew(i2c, I2C_DCM_DISABLE, OFFSET_DCM_EN); |
| |
| mtk_i2c_writew(i2c, i2c->timing_reg, OFFSET_TIMING); |
| mtk_i2c_writew(i2c, i2c->high_speed_reg, OFFSET_HS); |
| if (i2c->dev_comp->ltiming_adjust) |
| mtk_i2c_writew(i2c, i2c->ltiming_reg, OFFSET_LTIMING); |
| |
| if (i2c->speed_hz <= I2C_MAX_STANDARD_MODE_FREQ) |
| ext_conf_val = I2C_ST_START_CON; |
| else |
| ext_conf_val = I2C_FS_START_CON; |
| |
| if (i2c->dev_comp->timing_adjust) { |
| ext_conf_val = i2c->ac_timing.ext; |
| mtk_i2c_writew(i2c, i2c->ac_timing.inter_clk_div, |
| OFFSET_CLOCK_DIV); |
| mtk_i2c_writew(i2c, I2C_SCL_MIS_COMP_VALUE, |
| OFFSET_SCL_MIS_COMP_POINT); |
| mtk_i2c_writew(i2c, i2c->ac_timing.sda_timing, |
| OFFSET_SDA_TIMING); |
| |
| if (i2c->dev_comp->ltiming_adjust) { |
| mtk_i2c_writew(i2c, i2c->ac_timing.htiming, |
| OFFSET_TIMING); |
| mtk_i2c_writew(i2c, i2c->ac_timing.hs, OFFSET_HS); |
| mtk_i2c_writew(i2c, i2c->ac_timing.ltiming, |
| OFFSET_LTIMING); |
| } else { |
| mtk_i2c_writew(i2c, i2c->ac_timing.scl_hl_ratio, |
| OFFSET_SCL_HIGH_LOW_RATIO); |
| mtk_i2c_writew(i2c, i2c->ac_timing.hs_scl_hl_ratio, |
| OFFSET_HS_SCL_HIGH_LOW_RATIO); |
| mtk_i2c_writew(i2c, i2c->ac_timing.sta_stop, |
| OFFSET_STA_STO_AC_TIMING); |
| mtk_i2c_writew(i2c, i2c->ac_timing.hs_sta_stop, |
| OFFSET_HS_STA_STO_AC_TIMING); |
| } |
| } |
| mtk_i2c_writew(i2c, ext_conf_val, OFFSET_EXT_CONF); |
| |
| /* If use i2c pin from PMIC mt6397 side, need set PATH_DIR first */ |
| if (i2c->have_pmic) |
| mtk_i2c_writew(i2c, I2C_CONTROL_WRAPPER, OFFSET_PATH_DIR); |
| |
| control_reg = I2C_CONTROL_ACKERR_DET_EN | |
| I2C_CONTROL_CLK_EXT_EN | I2C_CONTROL_DMA_EN; |
| if (i2c->dev_comp->dma_sync) |
| control_reg |= I2C_CONTROL_DMAACK_EN | I2C_CONTROL_ASYNC_MODE; |
| |
| mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL); |
| mtk_i2c_writew(i2c, I2C_DELAY_LEN, OFFSET_DELAY_LEN); |
| } |
| |
| static const struct i2c_spec_values *mtk_i2c_get_spec(unsigned int speed) |
| { |
| if (speed <= I2C_MAX_STANDARD_MODE_FREQ) |
| return &standard_mode_spec; |
| else if (speed <= I2C_MAX_FAST_MODE_FREQ) |
| return &fast_mode_spec; |
| else |
| return &fast_mode_plus_spec; |
| } |
| |
| static int mtk_i2c_max_step_cnt(unsigned int target_speed) |
| { |
| if (target_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) |
| return MAX_HS_STEP_CNT_DIV; |
| else |
| return MAX_STEP_CNT_DIV; |
| } |
| |
| static int mtk_i2c_get_clk_div_restri(struct mtk_i2c *i2c, |
| unsigned int sample_cnt) |
| { |
| int clk_div_restri = 0; |
| |
| if (i2c->dev_comp->ltiming_adjust == 0) |
| return 0; |
| |
| if (sample_cnt == 1) { |
| if (i2c->ac_timing.inter_clk_div == 0) |
| clk_div_restri = 0; |
| else |
| clk_div_restri = 1; |
| } else { |
| if (i2c->ac_timing.inter_clk_div == 0) |
| clk_div_restri = -1; |
| else if (i2c->ac_timing.inter_clk_div == 1) |
| clk_div_restri = 0; |
| else |
| clk_div_restri = 1; |
| } |
| |
| return clk_div_restri; |
| } |
| |
| /* |
| * Check and Calculate i2c ac-timing |
| * |
| * Hardware design: |
| * sample_ns = (1000000000 * (sample_cnt + 1)) / clk_src |
| * xxx_cnt_div = spec->min_xxx_ns / sample_ns |
| * |
| * Sample_ns is rounded down for xxx_cnt_div would be greater |
| * than the smallest spec. |
| * The sda_timing is chosen as the middle value between |
| * the largest and smallest. |
| */ |
| static int mtk_i2c_check_ac_timing(struct mtk_i2c *i2c, |
| unsigned int clk_src, |
| unsigned int check_speed, |
| unsigned int step_cnt, |
| unsigned int sample_cnt) |
| { |
| const struct i2c_spec_values *spec; |
| unsigned int su_sta_cnt, low_cnt, high_cnt, max_step_cnt; |
| unsigned int sda_max, sda_min, clk_ns, max_sta_cnt = 0x3f; |
| unsigned int sample_ns = div_u64(1000000000ULL * (sample_cnt + 1), |
| clk_src); |
| |
| if (!i2c->dev_comp->timing_adjust) |
| return 0; |
| |
| if (i2c->dev_comp->ltiming_adjust) |
| max_sta_cnt = 0x100; |
| |
| spec = mtk_i2c_get_spec(check_speed); |
| |
| if (i2c->dev_comp->ltiming_adjust) |
| clk_ns = 1000000000 / clk_src; |
| else |
| clk_ns = sample_ns / 2; |
| |
| su_sta_cnt = DIV_ROUND_UP(spec->min_su_sta_ns + |
| i2c->timing_info.scl_int_delay_ns, clk_ns); |
| if (su_sta_cnt > max_sta_cnt) |
| return -1; |
| |
| low_cnt = DIV_ROUND_UP(spec->min_low_ns, sample_ns); |
| max_step_cnt = mtk_i2c_max_step_cnt(check_speed); |
| if ((2 * step_cnt) > low_cnt && low_cnt < max_step_cnt) { |
| if (low_cnt > step_cnt) { |
| high_cnt = 2 * step_cnt - low_cnt; |
| } else { |
| high_cnt = step_cnt; |
| low_cnt = step_cnt; |
| } |
| } else { |
| return -2; |
| } |
| |
| sda_max = spec->max_hd_dat_ns / sample_ns; |
| if (sda_max > low_cnt) |
| sda_max = 0; |
| |
| sda_min = DIV_ROUND_UP(spec->min_su_dat_ns, sample_ns); |
| if (sda_min < low_cnt) |
| sda_min = 0; |
| |
| if (sda_min > sda_max) |
| return -3; |
| |
| if (check_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) { |
| if (i2c->dev_comp->ltiming_adjust) { |
| i2c->ac_timing.hs = I2C_TIME_DEFAULT_VALUE | |
| (sample_cnt << 12) | (high_cnt << 8); |
| i2c->ac_timing.ltiming &= ~GENMASK(15, 9); |
| i2c->ac_timing.ltiming |= (sample_cnt << 12) | |
| (low_cnt << 9); |
| i2c->ac_timing.ext &= ~GENMASK(7, 1); |
| i2c->ac_timing.ext |= (su_sta_cnt << 1) | (1 << 0); |
| } else { |
| i2c->ac_timing.hs_scl_hl_ratio = (1 << 12) | |
| (high_cnt << 6) | low_cnt; |
| i2c->ac_timing.hs_sta_stop = (su_sta_cnt << 8) | |
| su_sta_cnt; |
| } |
| i2c->ac_timing.sda_timing &= ~GENMASK(11, 6); |
| i2c->ac_timing.sda_timing |= (1 << 12) | |
| ((sda_max + sda_min) / 2) << 6; |
| } else { |
| if (i2c->dev_comp->ltiming_adjust) { |
| i2c->ac_timing.htiming = (sample_cnt << 8) | (high_cnt); |
| i2c->ac_timing.ltiming = (sample_cnt << 6) | (low_cnt); |
| i2c->ac_timing.ext = (su_sta_cnt << 8) | (1 << 0); |
| } else { |
| i2c->ac_timing.scl_hl_ratio = (1 << 12) | |
| (high_cnt << 6) | low_cnt; |
| i2c->ac_timing.sta_stop = (su_sta_cnt << 8) | |
| su_sta_cnt; |
| } |
| |
| i2c->ac_timing.sda_timing = (1 << 12) | |
| (sda_max + sda_min) / 2; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Calculate i2c port speed |
| * |
| * Hardware design: |
| * i2c_bus_freq = parent_clk / (clock_div * 2 * sample_cnt * step_cnt) |
| * clock_div: fixed in hardware, but may be various in different SoCs |
| * |
| * The calculation want to pick the highest bus frequency that is still |
| * less than or equal to i2c->speed_hz. The calculation try to get |
| * sample_cnt and step_cn |
| */ |
| static int mtk_i2c_calculate_speed(struct mtk_i2c *i2c, unsigned int clk_src, |
| unsigned int target_speed, |
| unsigned int *timing_step_cnt, |
| unsigned int *timing_sample_cnt) |
| { |
| unsigned int step_cnt; |
| unsigned int sample_cnt; |
| unsigned int max_step_cnt; |
| unsigned int base_sample_cnt = MAX_SAMPLE_CNT_DIV; |
| unsigned int base_step_cnt; |
| unsigned int opt_div; |
| unsigned int best_mul; |
| unsigned int cnt_mul; |
| int ret = -EINVAL; |
| int clk_div_restri = 0; |
| |
| if (target_speed > I2C_MAX_HIGH_SPEED_MODE_FREQ) |
| target_speed = I2C_MAX_HIGH_SPEED_MODE_FREQ; |
| |
| max_step_cnt = mtk_i2c_max_step_cnt(target_speed); |
| base_step_cnt = max_step_cnt; |
| /* Find the best combination */ |
| opt_div = DIV_ROUND_UP(clk_src >> 1, target_speed); |
| best_mul = MAX_SAMPLE_CNT_DIV * max_step_cnt; |
| |
| /* Search for the best pair (sample_cnt, step_cnt) with |
| * 0 < sample_cnt < MAX_SAMPLE_CNT_DIV |
| * 0 < step_cnt < max_step_cnt |
| * sample_cnt * step_cnt >= opt_div |
| * optimizing for sample_cnt * step_cnt being minimal |
| */ |
| for (sample_cnt = 1; sample_cnt <= MAX_SAMPLE_CNT_DIV; sample_cnt++) { |
| clk_div_restri = mtk_i2c_get_clk_div_restri(i2c, sample_cnt); |
| step_cnt = DIV_ROUND_UP(opt_div + clk_div_restri, sample_cnt); |
| cnt_mul = step_cnt * sample_cnt; |
| if (step_cnt > max_step_cnt) |
| continue; |
| |
| if (cnt_mul < best_mul) { |
| ret = mtk_i2c_check_ac_timing(i2c, clk_src, |
| target_speed, step_cnt - 1, sample_cnt - 1); |
| if (ret) |
| continue; |
| |
| best_mul = cnt_mul; |
| base_sample_cnt = sample_cnt; |
| base_step_cnt = step_cnt; |
| if (best_mul == (opt_div + clk_div_restri)) |
| break; |
| } |
| } |
| |
| if (ret) |
| return -EINVAL; |
| |
| sample_cnt = base_sample_cnt; |
| step_cnt = base_step_cnt; |
| |
| if ((clk_src / (2 * (sample_cnt * step_cnt - clk_div_restri))) > |
| target_speed) { |
| /* In this case, hardware can't support such |
| * low i2c_bus_freq |
| */ |
| dev_dbg(i2c->dev, "Unsupported speed (%uhz)\n", target_speed); |
| return -EINVAL; |
| } |
| |
| *timing_step_cnt = step_cnt - 1; |
| *timing_sample_cnt = sample_cnt - 1; |
| |
| return 0; |
| } |
| |
| static int mtk_i2c_set_speed(struct mtk_i2c *i2c, unsigned int parent_clk) |
| { |
| unsigned int clk_src; |
| unsigned int step_cnt; |
| unsigned int sample_cnt; |
| unsigned int l_step_cnt; |
| unsigned int l_sample_cnt; |
| unsigned int target_speed; |
| unsigned int clk_div; |
| unsigned int max_clk_div; |
| int ret; |
| |
| target_speed = i2c->speed_hz; |
| parent_clk /= i2c->clk_src_div; |
| |
| if (i2c->dev_comp->timing_adjust && i2c->dev_comp->ltiming_adjust) |
| max_clk_div = MAX_CLOCK_DIV_5BITS; |
| else if (i2c->dev_comp->timing_adjust) |
| max_clk_div = MAX_CLOCK_DIV_8BITS; |
| else |
| max_clk_div = 1; |
| |
| for (clk_div = 1; clk_div <= max_clk_div; clk_div++) { |
| clk_src = parent_clk / clk_div; |
| i2c->ac_timing.inter_clk_div = clk_div - 1; |
| |
| if (target_speed > I2C_MAX_FAST_MODE_PLUS_FREQ) { |
| /* Set master code speed register */ |
| ret = mtk_i2c_calculate_speed(i2c, clk_src, |
| I2C_MAX_FAST_MODE_FREQ, |
| &l_step_cnt, |
| &l_sample_cnt); |
| if (ret < 0) |
| continue; |
| |
| i2c->timing_reg = (l_sample_cnt << 8) | l_step_cnt; |
| |
| /* Set the high speed mode register */ |
| ret = mtk_i2c_calculate_speed(i2c, clk_src, |
| target_speed, &step_cnt, |
| &sample_cnt); |
| if (ret < 0) |
| continue; |
| |
| i2c->high_speed_reg = I2C_TIME_DEFAULT_VALUE | |
| (sample_cnt << 12) | (step_cnt << 8); |
| |
| if (i2c->dev_comp->ltiming_adjust) |
| i2c->ltiming_reg = |
| (l_sample_cnt << 6) | l_step_cnt | |
| (sample_cnt << 12) | (step_cnt << 9); |
| } else { |
| ret = mtk_i2c_calculate_speed(i2c, clk_src, |
| target_speed, &l_step_cnt, |
| &l_sample_cnt); |
| if (ret < 0) |
| continue; |
| |
| i2c->timing_reg = (l_sample_cnt << 8) | l_step_cnt; |
| |
| /* Disable the high speed transaction */ |
| i2c->high_speed_reg = I2C_TIME_CLR_VALUE; |
| |
| if (i2c->dev_comp->ltiming_adjust) |
| i2c->ltiming_reg = |
| (l_sample_cnt << 6) | l_step_cnt; |
| } |
| |
| break; |
| } |
| |
| |
| return 0; |
| } |
| |
| static void i2c_dump_register(struct mtk_i2c *i2c) |
| { |
| dev_dbg(i2c->dev, "SLAVE_ADDR: 0x%x, INTR_MASK: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_SLAVE_ADDR), |
| mtk_i2c_readw(i2c, OFFSET_INTR_MASK)); |
| dev_dbg(i2c->dev, "INTR_STAT: 0x%x, CONTROL: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_INTR_STAT), |
| mtk_i2c_readw(i2c, OFFSET_CONTROL)); |
| dev_dbg(i2c->dev, "TRANSFER_LEN: 0x%x, TRANSAC_LEN: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_TRANSFER_LEN), |
| mtk_i2c_readw(i2c, OFFSET_TRANSAC_LEN)); |
| dev_dbg(i2c->dev, "DELAY_LEN: 0x%x, HTIMING: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_DELAY_LEN), |
| mtk_i2c_readw(i2c, OFFSET_TIMING)); |
| dev_dbg(i2c->dev, "START: 0x%x, EXT_CONF: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_START), |
| mtk_i2c_readw(i2c, OFFSET_EXT_CONF)); |
| dev_dbg(i2c->dev, "HS: 0x%x, IO_CONFIG: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_HS), |
| mtk_i2c_readw(i2c, OFFSET_IO_CONFIG)); |
| dev_dbg(i2c->dev, "DCM_EN: 0x%x, TRANSFER_LEN_AUX: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_DCM_EN), |
| mtk_i2c_readw(i2c, OFFSET_TRANSFER_LEN_AUX)); |
| dev_dbg(i2c->dev, "CLOCK_DIV: 0x%x, FIFO_STAT: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_CLOCK_DIV), |
| mtk_i2c_readw(i2c, OFFSET_FIFO_STAT)); |
| dev_dbg(i2c->dev, "DEBUGCTRL : 0x%x, DEBUGSTAT: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_DEBUGCTRL), |
| mtk_i2c_readw(i2c, OFFSET_DEBUGSTAT)); |
| if (i2c->dev_comp->regs == mt_i2c_regs_v2) { |
| dev_dbg(i2c->dev, "LTIMING: 0x%x, MULTI_DMA: 0x%x\n", |
| mtk_i2c_readw(i2c, OFFSET_LTIMING), |
| mtk_i2c_readw(i2c, OFFSET_MULTI_DMA)); |
| } |
| dev_dbg(i2c->dev, "\nDMA_INT_FLAG: 0x%x, DMA_INT_EN: 0x%x\n", |
| readl(i2c->pdmabase + OFFSET_INT_FLAG), |
| readl(i2c->pdmabase + OFFSET_INT_EN)); |
| dev_dbg(i2c->dev, "DMA_EN: 0x%x, DMA_CON: 0x%x\n", |
| readl(i2c->pdmabase + OFFSET_EN), |
| readl(i2c->pdmabase + OFFSET_CON)); |
| dev_dbg(i2c->dev, "DMA_TX_MEM_ADDR: 0x%x, DMA_RX_MEM_ADDR: 0x%x\n", |
| readl(i2c->pdmabase + OFFSET_TX_MEM_ADDR), |
| readl(i2c->pdmabase + OFFSET_RX_MEM_ADDR)); |
| dev_dbg(i2c->dev, "DMA_TX_LEN: 0x%x, DMA_RX_LEN: 0x%x\n", |
| readl(i2c->pdmabase + OFFSET_TX_LEN), |
| readl(i2c->pdmabase + OFFSET_RX_LEN)); |
| dev_dbg(i2c->dev, "DMA_TX_4G_MODE: 0x%x, DMA_RX_4G_MODE: 0x%x", |
| readl(i2c->pdmabase + OFFSET_TX_4G_MODE), |
| readl(i2c->pdmabase + OFFSET_RX_4G_MODE)); |
| } |
| |
| static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs, |
| int num, int left_num) |
| { |
| u16 addr_reg; |
| u16 start_reg; |
| u16 control_reg; |
| u16 restart_flag = 0; |
| u16 dma_sync = 0; |
| u32 reg_4g_mode; |
| u32 reg_dma_reset; |
| u8 *dma_rd_buf = NULL; |
| u8 *dma_wr_buf = NULL; |
| dma_addr_t rpaddr = 0; |
| dma_addr_t wpaddr = 0; |
| int ret; |
| |
| i2c->irq_stat = 0; |
| |
| if (i2c->auto_restart) |
| restart_flag = I2C_RS_TRANSFER; |
| |
| reinit_completion(&i2c->msg_complete); |
| |
| if (i2c->dev_comp->apdma_sync && |
| i2c->op != I2C_MASTER_WRRD && num > 1) { |
| mtk_i2c_writew(i2c, 0x00, OFFSET_DEBUGCTRL); |
| writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_WARM_RST, |
| i2c->pdmabase + OFFSET_RST); |
| |
| ret = readw_poll_timeout(i2c->pdmabase + OFFSET_RST, |
| reg_dma_reset, |
| !(reg_dma_reset & I2C_DMA_WARM_RST), |
| 0, 100); |
| if (ret) { |
| dev_err(i2c->dev, "DMA warm reset timeout\n"); |
| return -ETIMEDOUT; |
| } |
| |
| writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST); |
| mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST, OFFSET_SOFTRESET); |
| mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET); |
| mtk_i2c_writew(i2c, I2C_RELIABILITY | I2C_DMAACK_ENABLE, |
| OFFSET_DEBUGCTRL); |
| } |
| |
| control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) & |
| ~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS); |
| if ((i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) || (left_num >= 1)) |
| control_reg |= I2C_CONTROL_RS; |
| |
| if (i2c->op == I2C_MASTER_WRRD) |
| control_reg |= I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS; |
| |
| mtk_i2c_writew(i2c, control_reg, OFFSET_CONTROL); |
| |
| addr_reg = i2c_8bit_addr_from_msg(msgs); |
| mtk_i2c_writew(i2c, addr_reg, OFFSET_SLAVE_ADDR); |
| |
| /* Clear interrupt status */ |
| mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR | |
| I2C_ARB_LOST | I2C_TRANSAC_COMP, OFFSET_INTR_STAT); |
| |
| mtk_i2c_writew(i2c, I2C_FIFO_ADDR_CLR, OFFSET_FIFO_ADDR_CLR); |
| |
| /* Enable interrupt */ |
| mtk_i2c_writew(i2c, restart_flag | I2C_HS_NACKERR | I2C_ACKERR | |
| I2C_ARB_LOST | I2C_TRANSAC_COMP, OFFSET_INTR_MASK); |
| |
| /* Set transfer and transaction len */ |
| if (i2c->op == I2C_MASTER_WRRD) { |
| if (i2c->dev_comp->aux_len_reg) { |
| mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN); |
| mtk_i2c_writew(i2c, (msgs + 1)->len, |
| OFFSET_TRANSFER_LEN_AUX); |
| } else { |
| mtk_i2c_writew(i2c, msgs->len | ((msgs + 1)->len) << 8, |
| OFFSET_TRANSFER_LEN); |
| } |
| mtk_i2c_writew(i2c, I2C_WRRD_TRANAC_VALUE, OFFSET_TRANSAC_LEN); |
| } else { |
| mtk_i2c_writew(i2c, msgs->len, OFFSET_TRANSFER_LEN); |
| mtk_i2c_writew(i2c, num, OFFSET_TRANSAC_LEN); |
| } |
| |
| if (i2c->dev_comp->apdma_sync) { |
| dma_sync = I2C_DMA_SKIP_CONFIG | I2C_DMA_ASYNC_MODE; |
| if (i2c->op == I2C_MASTER_WRRD) |
| dma_sync |= I2C_DMA_DIR_CHANGE; |
| } |
| |
| /* Prepare buffer data to start transfer */ |
| if (i2c->op == I2C_MASTER_RD) { |
| writel(I2C_DMA_INT_FLAG_NONE, i2c->pdmabase + OFFSET_INT_FLAG); |
| writel(I2C_DMA_CON_RX | dma_sync, i2c->pdmabase + OFFSET_CON); |
| |
| dma_rd_buf = i2c_get_dma_safe_msg_buf(msgs, 1); |
| if (!dma_rd_buf) |
| return -ENOMEM; |
| |
| rpaddr = dma_map_single(i2c->dev, dma_rd_buf, |
| msgs->len, DMA_FROM_DEVICE); |
| if (dma_mapping_error(i2c->dev, rpaddr)) { |
| i2c_put_dma_safe_msg_buf(dma_rd_buf, msgs, false); |
| |
| return -ENOMEM; |
| } |
| |
| if (i2c->dev_comp->max_dma_support > 32) { |
| reg_4g_mode = upper_32_bits(rpaddr); |
| writel(reg_4g_mode, i2c->pdmabase + OFFSET_RX_4G_MODE); |
| } |
| |
| writel((u32)rpaddr, i2c->pdmabase + OFFSET_RX_MEM_ADDR); |
| writel(msgs->len, i2c->pdmabase + OFFSET_RX_LEN); |
| } else if (i2c->op == I2C_MASTER_WR) { |
| writel(I2C_DMA_INT_FLAG_NONE, i2c->pdmabase + OFFSET_INT_FLAG); |
| writel(I2C_DMA_CON_TX | dma_sync, i2c->pdmabase + OFFSET_CON); |
| |
| dma_wr_buf = i2c_get_dma_safe_msg_buf(msgs, 1); |
| if (!dma_wr_buf) |
| return -ENOMEM; |
| |
| wpaddr = dma_map_single(i2c->dev, dma_wr_buf, |
| msgs->len, DMA_TO_DEVICE); |
| if (dma_mapping_error(i2c->dev, wpaddr)) { |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, false); |
| |
| return -ENOMEM; |
| } |
| |
| if (i2c->dev_comp->max_dma_support > 32) { |
| reg_4g_mode = upper_32_bits(wpaddr); |
| writel(reg_4g_mode, i2c->pdmabase + OFFSET_TX_4G_MODE); |
| } |
| |
| writel((u32)wpaddr, i2c->pdmabase + OFFSET_TX_MEM_ADDR); |
| writel(msgs->len, i2c->pdmabase + OFFSET_TX_LEN); |
| } else { |
| writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_INT_FLAG); |
| writel(I2C_DMA_CLR_FLAG | dma_sync, i2c->pdmabase + OFFSET_CON); |
| |
| dma_wr_buf = i2c_get_dma_safe_msg_buf(msgs, 1); |
| if (!dma_wr_buf) |
| return -ENOMEM; |
| |
| wpaddr = dma_map_single(i2c->dev, dma_wr_buf, |
| msgs->len, DMA_TO_DEVICE); |
| if (dma_mapping_error(i2c->dev, wpaddr)) { |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, false); |
| |
| return -ENOMEM; |
| } |
| |
| dma_rd_buf = i2c_get_dma_safe_msg_buf((msgs + 1), 1); |
| if (!dma_rd_buf) { |
| dma_unmap_single(i2c->dev, wpaddr, |
| msgs->len, DMA_TO_DEVICE); |
| |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, false); |
| |
| return -ENOMEM; |
| } |
| |
| rpaddr = dma_map_single(i2c->dev, dma_rd_buf, |
| (msgs + 1)->len, |
| DMA_FROM_DEVICE); |
| if (dma_mapping_error(i2c->dev, rpaddr)) { |
| dma_unmap_single(i2c->dev, wpaddr, |
| msgs->len, DMA_TO_DEVICE); |
| |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, false); |
| i2c_put_dma_safe_msg_buf(dma_rd_buf, (msgs + 1), false); |
| |
| return -ENOMEM; |
| } |
| |
| if (i2c->dev_comp->max_dma_support > 32) { |
| reg_4g_mode = upper_32_bits(wpaddr); |
| writel(reg_4g_mode, i2c->pdmabase + OFFSET_TX_4G_MODE); |
| |
| reg_4g_mode = upper_32_bits(rpaddr); |
| writel(reg_4g_mode, i2c->pdmabase + OFFSET_RX_4G_MODE); |
| } |
| |
| writel((u32)wpaddr, i2c->pdmabase + OFFSET_TX_MEM_ADDR); |
| writel((u32)rpaddr, i2c->pdmabase + OFFSET_RX_MEM_ADDR); |
| writel(msgs->len, i2c->pdmabase + OFFSET_TX_LEN); |
| writel((msgs + 1)->len, i2c->pdmabase + OFFSET_RX_LEN); |
| } |
| |
| writel(I2C_DMA_START_EN, i2c->pdmabase + OFFSET_EN); |
| |
| if (!i2c->auto_restart) { |
| start_reg = I2C_TRANSAC_START; |
| } else { |
| start_reg = I2C_TRANSAC_START | I2C_RS_MUL_TRIG; |
| if (left_num >= 1) |
| start_reg |= I2C_RS_MUL_CNFG; |
| } |
| mtk_i2c_writew(i2c, start_reg, OFFSET_START); |
| |
| ret = wait_for_completion_timeout(&i2c->msg_complete, |
| i2c->adap.timeout); |
| |
| /* Clear interrupt mask */ |
| mtk_i2c_writew(i2c, ~(restart_flag | I2C_HS_NACKERR | I2C_ACKERR | |
| I2C_ARB_LOST | I2C_TRANSAC_COMP), OFFSET_INTR_MASK); |
| |
| if (i2c->op == I2C_MASTER_WR) { |
| dma_unmap_single(i2c->dev, wpaddr, |
| msgs->len, DMA_TO_DEVICE); |
| |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, true); |
| } else if (i2c->op == I2C_MASTER_RD) { |
| dma_unmap_single(i2c->dev, rpaddr, |
| msgs->len, DMA_FROM_DEVICE); |
| |
| i2c_put_dma_safe_msg_buf(dma_rd_buf, msgs, true); |
| } else { |
| dma_unmap_single(i2c->dev, wpaddr, msgs->len, |
| DMA_TO_DEVICE); |
| dma_unmap_single(i2c->dev, rpaddr, (msgs + 1)->len, |
| DMA_FROM_DEVICE); |
| |
| i2c_put_dma_safe_msg_buf(dma_wr_buf, msgs, true); |
| i2c_put_dma_safe_msg_buf(dma_rd_buf, (msgs + 1), true); |
| } |
| |
| if (ret == 0) { |
| dev_dbg(i2c->dev, "addr: %x, transfer timeout\n", msgs->addr); |
| i2c_dump_register(i2c); |
| mtk_i2c_init_hw(i2c); |
| return -ETIMEDOUT; |
| } |
| |
| if (i2c->irq_stat & (I2C_HS_NACKERR | I2C_ACKERR)) { |
| dev_dbg(i2c->dev, "addr: %x, transfer ACK error\n", msgs->addr); |
| mtk_i2c_init_hw(i2c); |
| return -ENXIO; |
| } |
| |
| return 0; |
| } |
| |
| static int mtk_i2c_transfer(struct i2c_adapter *adap, |
| struct i2c_msg msgs[], int num) |
| { |
| int ret; |
| int left_num = num; |
| struct mtk_i2c *i2c = i2c_get_adapdata(adap); |
| |
| ret = clk_bulk_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| if (ret) |
| return ret; |
| |
| i2c->auto_restart = i2c->dev_comp->auto_restart; |
| |
| /* checking if we can skip restart and optimize using WRRD mode */ |
| if (i2c->auto_restart && num == 2) { |
| if (!(msgs[0].flags & I2C_M_RD) && (msgs[1].flags & I2C_M_RD) && |
| msgs[0].addr == msgs[1].addr) { |
| i2c->auto_restart = 0; |
| } |
| } |
| |
| if (i2c->auto_restart && num >= 2 && |
| i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) |
| /* ignore the first restart irq after the master code, |
| * otherwise the first transfer will be discarded. |
| */ |
| i2c->ignore_restart_irq = true; |
| else |
| i2c->ignore_restart_irq = false; |
| |
| while (left_num--) { |
| if (!msgs->buf) { |
| dev_dbg(i2c->dev, "data buffer is NULL.\n"); |
| ret = -EINVAL; |
| goto err_exit; |
| } |
| |
| if (msgs->flags & I2C_M_RD) |
| i2c->op = I2C_MASTER_RD; |
| else |
| i2c->op = I2C_MASTER_WR; |
| |
| if (!i2c->auto_restart) { |
| if (num > 1) { |
| /* combined two messages into one transaction */ |
| i2c->op = I2C_MASTER_WRRD; |
| left_num--; |
| } |
| } |
| |
| /* always use DMA mode. */ |
| ret = mtk_i2c_do_transfer(i2c, msgs, num, left_num); |
| if (ret < 0) |
| goto err_exit; |
| |
| msgs++; |
| } |
| /* the return value is number of executed messages */ |
| ret = num; |
| |
| err_exit: |
| clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| return ret; |
| } |
| |
| static irqreturn_t mtk_i2c_irq(int irqno, void *dev_id) |
| { |
| struct mtk_i2c *i2c = dev_id; |
| u16 restart_flag = 0; |
| u16 intr_stat; |
| |
| if (i2c->auto_restart) |
| restart_flag = I2C_RS_TRANSFER; |
| |
| intr_stat = mtk_i2c_readw(i2c, OFFSET_INTR_STAT); |
| mtk_i2c_writew(i2c, intr_stat, OFFSET_INTR_STAT); |
| |
| /* |
| * when occurs ack error, i2c controller generate two interrupts |
| * first is the ack error interrupt, then the complete interrupt |
| * i2c->irq_stat need keep the two interrupt value. |
| */ |
| i2c->irq_stat |= intr_stat; |
| |
| if (i2c->ignore_restart_irq && (i2c->irq_stat & restart_flag)) { |
| i2c->ignore_restart_irq = false; |
| i2c->irq_stat = 0; |
| mtk_i2c_writew(i2c, I2C_RS_MUL_CNFG | I2C_RS_MUL_TRIG | |
| I2C_TRANSAC_START, OFFSET_START); |
| } else { |
| if (i2c->irq_stat & (I2C_TRANSAC_COMP | restart_flag)) |
| complete(&i2c->msg_complete); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static u32 mtk_i2c_functionality(struct i2c_adapter *adap) |
| { |
| if (i2c_check_quirks(adap, I2C_AQ_NO_ZERO_LEN)) |
| return I2C_FUNC_I2C | |
| (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); |
| else |
| return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; |
| } |
| |
| static const struct i2c_algorithm mtk_i2c_algorithm = { |
| .master_xfer = mtk_i2c_transfer, |
| .functionality = mtk_i2c_functionality, |
| }; |
| |
| static int mtk_i2c_parse_dt(struct device_node *np, struct mtk_i2c *i2c) |
| { |
| int ret; |
| |
| ret = of_property_read_u32(np, "clock-frequency", &i2c->speed_hz); |
| if (ret < 0) |
| i2c->speed_hz = I2C_MAX_STANDARD_MODE_FREQ; |
| |
| ret = of_property_read_u32(np, "clock-div", &i2c->clk_src_div); |
| if (ret < 0) |
| return ret; |
| |
| if (i2c->clk_src_div == 0) |
| return -EINVAL; |
| |
| i2c->have_pmic = of_property_read_bool(np, "mediatek,have-pmic"); |
| i2c->use_push_pull = |
| of_property_read_bool(np, "mediatek,use-push-pull"); |
| |
| i2c_parse_fw_timings(i2c->dev, &i2c->timing_info, true); |
| |
| return 0; |
| } |
| |
| static int mtk_i2c_probe(struct platform_device *pdev) |
| { |
| int ret = 0; |
| struct mtk_i2c *i2c; |
| struct resource *res; |
| int i, irq, speed_clk; |
| |
| i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL); |
| if (!i2c) |
| return -ENOMEM; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| i2c->base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(i2c->base)) |
| return PTR_ERR(i2c->base); |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 1); |
| i2c->pdmabase = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(i2c->pdmabase)) |
| return PTR_ERR(i2c->pdmabase); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| init_completion(&i2c->msg_complete); |
| |
| i2c->dev_comp = of_device_get_match_data(&pdev->dev); |
| i2c->adap.dev.of_node = pdev->dev.of_node; |
| i2c->dev = &pdev->dev; |
| i2c->adap.dev.parent = &pdev->dev; |
| i2c->adap.owner = THIS_MODULE; |
| i2c->adap.algo = &mtk_i2c_algorithm; |
| i2c->adap.quirks = i2c->dev_comp->quirks; |
| i2c->adap.timeout = 2 * HZ; |
| i2c->adap.retries = 1; |
| i2c->adap.bus_regulator = devm_regulator_get_optional(&pdev->dev, "vbus"); |
| if (IS_ERR(i2c->adap.bus_regulator)) { |
| if (PTR_ERR(i2c->adap.bus_regulator) == -ENODEV) |
| i2c->adap.bus_regulator = NULL; |
| else |
| return PTR_ERR(i2c->adap.bus_regulator); |
| } |
| |
| ret = mtk_i2c_parse_dt(pdev->dev.of_node, i2c); |
| if (ret) |
| return -EINVAL; |
| |
| if (i2c->have_pmic && !i2c->dev_comp->pmic_i2c) |
| return -EINVAL; |
| |
| /* Fill in clk-bulk IDs */ |
| for (i = 0; i < I2C_MT65XX_CLK_MAX; i++) |
| i2c->clocks[i].id = i2c_mt65xx_clk_ids[i]; |
| |
| /* Get clocks one by one, some may be optional */ |
| i2c->clocks[I2C_MT65XX_CLK_MAIN].clk = devm_clk_get(&pdev->dev, "main"); |
| if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_MAIN].clk)) { |
| dev_err(&pdev->dev, "cannot get main clock\n"); |
| return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_MAIN].clk); |
| } |
| |
| i2c->clocks[I2C_MT65XX_CLK_DMA].clk = devm_clk_get(&pdev->dev, "dma"); |
| if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_DMA].clk)) { |
| dev_err(&pdev->dev, "cannot get dma clock\n"); |
| return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_DMA].clk); |
| } |
| |
| i2c->clocks[I2C_MT65XX_CLK_ARB].clk = devm_clk_get_optional(&pdev->dev, "arb"); |
| if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk)) |
| return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_ARB].clk); |
| |
| if (i2c->have_pmic) { |
| i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = devm_clk_get(&pdev->dev, "pmic"); |
| if (IS_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk)) { |
| dev_err(&pdev->dev, "cannot get pmic clock\n"); |
| return PTR_ERR(i2c->clocks[I2C_MT65XX_CLK_PMIC].clk); |
| } |
| speed_clk = I2C_MT65XX_CLK_PMIC; |
| } else { |
| i2c->clocks[I2C_MT65XX_CLK_PMIC].clk = NULL; |
| speed_clk = I2C_MT65XX_CLK_MAIN; |
| } |
| |
| strscpy(i2c->adap.name, I2C_DRV_NAME, sizeof(i2c->adap.name)); |
| |
| ret = mtk_i2c_set_speed(i2c, clk_get_rate(i2c->clocks[speed_clk].clk)); |
| if (ret) { |
| dev_err(&pdev->dev, "Failed to set the speed.\n"); |
| return -EINVAL; |
| } |
| |
| if (i2c->dev_comp->max_dma_support > 32) { |
| ret = dma_set_mask(&pdev->dev, |
| DMA_BIT_MASK(i2c->dev_comp->max_dma_support)); |
| if (ret) { |
| dev_err(&pdev->dev, "dma_set_mask return error.\n"); |
| return ret; |
| } |
| } |
| |
| ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| if (ret) { |
| dev_err(&pdev->dev, "clock enable failed!\n"); |
| return ret; |
| } |
| mtk_i2c_init_hw(i2c); |
| clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| |
| ret = devm_request_irq(&pdev->dev, irq, mtk_i2c_irq, |
| IRQF_NO_SUSPEND | IRQF_TRIGGER_NONE, |
| dev_name(&pdev->dev), i2c); |
| if (ret < 0) { |
| dev_err(&pdev->dev, |
| "Request I2C IRQ %d fail\n", irq); |
| goto err_bulk_unprepare; |
| } |
| |
| i2c_set_adapdata(&i2c->adap, i2c); |
| ret = i2c_add_adapter(&i2c->adap); |
| if (ret) |
| goto err_bulk_unprepare; |
| |
| platform_set_drvdata(pdev, i2c); |
| |
| return 0; |
| |
| err_bulk_unprepare: |
| clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| |
| return ret; |
| } |
| |
| static int mtk_i2c_remove(struct platform_device *pdev) |
| { |
| struct mtk_i2c *i2c = platform_get_drvdata(pdev); |
| |
| i2c_del_adapter(&i2c->adap); |
| |
| clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int mtk_i2c_suspend_noirq(struct device *dev) |
| { |
| struct mtk_i2c *i2c = dev_get_drvdata(dev); |
| |
| i2c_mark_adapter_suspended(&i2c->adap); |
| clk_bulk_unprepare(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| |
| return 0; |
| } |
| |
| static int mtk_i2c_resume_noirq(struct device *dev) |
| { |
| int ret; |
| struct mtk_i2c *i2c = dev_get_drvdata(dev); |
| |
| ret = clk_bulk_prepare_enable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| if (ret) { |
| dev_err(dev, "clock enable failed!\n"); |
| return ret; |
| } |
| |
| mtk_i2c_init_hw(i2c); |
| |
| clk_bulk_disable(I2C_MT65XX_CLK_MAX, i2c->clocks); |
| |
| i2c_mark_adapter_resumed(&i2c->adap); |
| |
| return 0; |
| } |
| #endif |
| |
| static const struct dev_pm_ops mtk_i2c_pm = { |
| SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mtk_i2c_suspend_noirq, |
| mtk_i2c_resume_noirq) |
| }; |
| |
| static struct platform_driver mtk_i2c_driver = { |
| .probe = mtk_i2c_probe, |
| .remove = mtk_i2c_remove, |
| .driver = { |
| .name = I2C_DRV_NAME, |
| .pm = &mtk_i2c_pm, |
| .of_match_table = of_match_ptr(mtk_i2c_of_match), |
| }, |
| }; |
| |
| module_platform_driver(mtk_i2c_driver); |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_DESCRIPTION("MediaTek I2C Bus Driver"); |
| MODULE_AUTHOR("Xudong Chen <xudong.chen@mediatek.com>"); |
