| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * drivers/clocksource/arm_global_timer.c | |
| * | |
| * Copyright (C) 2013 STMicroelectronics (R&D) Limited. | |
| * Author: Stuart Menefy <stuart.menefy@st.com> | |
| * Author: Srinivas Kandagatla <srinivas.kandagatla@st.com> | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/bitfield.h> | |
| #include <linux/clocksource.h> | |
| #include <linux/clockchips.h> | |
| #include <linux/cpu.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/io.h> | |
| #include <linux/of.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_address.h> | |
| #include <linux/sched_clock.h> | |
| #include <asm/cputype.h> | |
| #define GT_COUNTER0 0x00 | |
| #define GT_COUNTER1 0x04 | |
| #define GT_CONTROL 0x08 | |
| #define GT_CONTROL_TIMER_ENABLE BIT(0) /* this bit is NOT banked */ | |
| #define GT_CONTROL_COMP_ENABLE BIT(1) /* banked */ | |
| #define GT_CONTROL_IRQ_ENABLE BIT(2) /* banked */ | |
| #define GT_CONTROL_AUTO_INC BIT(3) /* banked */ | |
| #define GT_CONTROL_PRESCALER_MASK GENMASK(15, 8) | |
| #define GT_INT_STATUS 0x0c | |
| #define GT_INT_STATUS_EVENT_FLAG BIT(0) | |
| #define GT_COMP0 0x10 | |
| #define GT_COMP1 0x14 | |
| #define GT_AUTO_INC 0x18 | |
| #define MAX_F_ERR 50 | |
| /* | |
| * We are expecting to be clocked by the ARM peripheral clock. | |
| * | |
| * Note: it is assumed we are using a prescaler value of zero, so this is | |
| * the units for all operations. | |
| */ | |
| static void __iomem *gt_base; | |
| static struct notifier_block gt_clk_rate_change_nb; | |
| static u32 gt_psv_new, gt_psv_bck; | |
| static unsigned long gt_target_rate; | |
| static int gt_ppi; | |
| static struct clock_event_device __percpu *gt_evt; | |
| /* | |
| * To get the value from the Global Timer Counter register proceed as follows: | |
| * 1. Read the upper 32-bit timer counter register | |
| * 2. Read the lower 32-bit timer counter register | |
| * 3. Read the upper 32-bit timer counter register again. If the value is | |
| * different to the 32-bit upper value read previously, go back to step 2. | |
| * Otherwise the 64-bit timer counter value is correct. | |
| */ | |
| static u64 notrace _gt_counter_read(void) | |
| { | |
| u64 counter; | |
| u32 lower; | |
| u32 upper, old_upper; | |
| upper = readl_relaxed(gt_base + GT_COUNTER1); | |
| do { | |
| old_upper = upper; | |
| lower = readl_relaxed(gt_base + GT_COUNTER0); | |
| upper = readl_relaxed(gt_base + GT_COUNTER1); | |
| } while (upper != old_upper); | |
| counter = upper; | |
| counter <<= 32; | |
| counter |= lower; | |
| return counter; | |
| } | |
| static u64 gt_counter_read(void) | |
| { | |
| return _gt_counter_read(); | |
| } | |
| /* | |
| * To ensure that updates to comparator value register do not set the | |
| * Interrupt Status Register proceed as follows: | |
| * 1. Clear the Comp Enable bit in the Timer Control Register. | |
| * 2. Write the lower 32-bit Comparator Value Register. | |
| * 3. Write the upper 32-bit Comparator Value Register. | |
| * 4. Set the Comp Enable bit and, if necessary, the IRQ enable bit. | |
| */ | |
| static void gt_compare_set(unsigned long delta, int periodic) | |
| { | |
| u64 counter = gt_counter_read(); | |
| unsigned long ctrl; | |
| counter += delta; | |
| ctrl = readl(gt_base + GT_CONTROL); | |
| ctrl &= ~(GT_CONTROL_COMP_ENABLE | GT_CONTROL_IRQ_ENABLE | | |
| GT_CONTROL_AUTO_INC); | |
| ctrl |= GT_CONTROL_TIMER_ENABLE; | |
| writel_relaxed(ctrl, gt_base + GT_CONTROL); | |
| writel_relaxed(lower_32_bits(counter), gt_base + GT_COMP0); | |
| writel_relaxed(upper_32_bits(counter), gt_base + GT_COMP1); | |
| if (periodic) { | |
| writel_relaxed(delta, gt_base + GT_AUTO_INC); | |
| ctrl |= GT_CONTROL_AUTO_INC; | |
| } | |
| ctrl |= GT_CONTROL_COMP_ENABLE | GT_CONTROL_IRQ_ENABLE; | |
| writel_relaxed(ctrl, gt_base + GT_CONTROL); | |
| } | |
| static int gt_clockevent_shutdown(struct clock_event_device *evt) | |
| { | |
| unsigned long ctrl; | |
| ctrl = readl(gt_base + GT_CONTROL); | |
| ctrl &= ~(GT_CONTROL_COMP_ENABLE | GT_CONTROL_IRQ_ENABLE | | |
| GT_CONTROL_AUTO_INC); | |
| writel(ctrl, gt_base + GT_CONTROL); | |
| return 0; | |
| } | |
| static int gt_clockevent_set_periodic(struct clock_event_device *evt) | |
| { | |
| gt_compare_set(DIV_ROUND_CLOSEST(gt_target_rate, HZ), 1); | |
| return 0; | |
| } | |
| static int gt_clockevent_set_next_event(unsigned long evt, | |
| struct clock_event_device *unused) | |
| { | |
| gt_compare_set(evt, 0); | |
| return 0; | |
| } | |
| static irqreturn_t gt_clockevent_interrupt(int irq, void *dev_id) | |
| { | |
| struct clock_event_device *evt = dev_id; | |
| if (!(readl_relaxed(gt_base + GT_INT_STATUS) & | |
| GT_INT_STATUS_EVENT_FLAG)) | |
| return IRQ_NONE; | |
| /** | |
| * ERRATA 740657( Global Timer can send 2 interrupts for | |
| * the same event in single-shot mode) | |
| * Workaround: | |
| * Either disable single-shot mode. | |
| * Or | |
| * Modify the Interrupt Handler to avoid the | |
| * offending sequence. This is achieved by clearing | |
| * the Global Timer flag _after_ having incremented | |
| * the Comparator register value to a higher value. | |
| */ | |
| if (clockevent_state_oneshot(evt)) | |
| gt_compare_set(ULONG_MAX, 0); | |
| writel_relaxed(GT_INT_STATUS_EVENT_FLAG, gt_base + GT_INT_STATUS); | |
| evt->event_handler(evt); | |
| return IRQ_HANDLED; | |
| } | |
| static int gt_starting_cpu(unsigned int cpu) | |
| { | |
| struct clock_event_device *clk = this_cpu_ptr(gt_evt); | |
| clk->name = "arm_global_timer"; | |
| clk->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT | | |
| CLOCK_EVT_FEAT_PERCPU; | |
| clk->set_state_shutdown = gt_clockevent_shutdown; | |
| clk->set_state_periodic = gt_clockevent_set_periodic; | |
| clk->set_state_oneshot = gt_clockevent_shutdown; | |
| clk->set_state_oneshot_stopped = gt_clockevent_shutdown; | |
| clk->set_next_event = gt_clockevent_set_next_event; | |
| clk->cpumask = cpumask_of(cpu); | |
| clk->rating = 300; | |
| clk->irq = gt_ppi; | |
| clockevents_config_and_register(clk, gt_target_rate, | |
| 1, 0xffffffff); | |
| enable_percpu_irq(clk->irq, IRQ_TYPE_NONE); | |
| return 0; | |
| } | |
| static int gt_dying_cpu(unsigned int cpu) | |
| { | |
| struct clock_event_device *clk = this_cpu_ptr(gt_evt); | |
| disable_percpu_irq(clk->irq); | |
| return 0; | |
| } | |
| static u64 gt_clocksource_read(struct clocksource *cs) | |
| { | |
| return gt_counter_read(); | |
| } | |
| static void gt_resume(struct clocksource *cs) | |
| { | |
| unsigned long ctrl; | |
| ctrl = readl(gt_base + GT_CONTROL); | |
| if (!(ctrl & GT_CONTROL_TIMER_ENABLE)) | |
| /* re-enable timer on resume */ | |
| writel(GT_CONTROL_TIMER_ENABLE, gt_base + GT_CONTROL); | |
| } | |
| static struct clocksource gt_clocksource = { | |
| .name = "arm_global_timer", | |
| .rating = 300, | |
| .read = gt_clocksource_read, | |
| .mask = CLOCKSOURCE_MASK(64), | |
| .flags = CLOCK_SOURCE_IS_CONTINUOUS, | |
| .resume = gt_resume, | |
| }; | |
| #ifdef CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK | |
| static u64 notrace gt_sched_clock_read(void) | |
| { | |
| return _gt_counter_read(); | |
| } | |
| #endif | |
| static unsigned long gt_read_long(void) | |
| { | |
| return readl_relaxed(gt_base + GT_COUNTER0); | |
| } | |
| static struct delay_timer gt_delay_timer = { | |
| .read_current_timer = gt_read_long, | |
| }; | |
| static void gt_write_presc(u32 psv) | |
| { | |
| u32 reg; | |
| reg = readl(gt_base + GT_CONTROL); | |
| reg &= ~GT_CONTROL_PRESCALER_MASK; | |
| reg |= FIELD_PREP(GT_CONTROL_PRESCALER_MASK, psv); | |
| writel(reg, gt_base + GT_CONTROL); | |
| } | |
| static u32 gt_read_presc(void) | |
| { | |
| u32 reg; | |
| reg = readl(gt_base + GT_CONTROL); | |
| return FIELD_GET(GT_CONTROL_PRESCALER_MASK, reg); | |
| } | |
| static void __init gt_delay_timer_init(void) | |
| { | |
| gt_delay_timer.freq = gt_target_rate; | |
| register_current_timer_delay(>_delay_timer); | |
| } | |
| static int __init gt_clocksource_init(unsigned int psv) | |
| { | |
| writel(0, gt_base + GT_CONTROL); | |
| writel(0, gt_base + GT_COUNTER0); | |
| writel(0, gt_base + GT_COUNTER1); | |
| /* set prescaler and enable timer on all the cores */ | |
| writel(FIELD_PREP(GT_CONTROL_PRESCALER_MASK, psv - 1) | | |
| GT_CONTROL_TIMER_ENABLE, gt_base + GT_CONTROL); | |
| #ifdef CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK | |
| sched_clock_register(gt_sched_clock_read, 64, gt_target_rate); | |
| #endif | |
| return clocksource_register_hz(>_clocksource, gt_target_rate); | |
| } | |
| static int gt_clk_rate_change_cb(struct notifier_block *nb, | |
| unsigned long event, void *data) | |
| { | |
| struct clk_notifier_data *ndata = data; | |
| switch (event) { | |
| case PRE_RATE_CHANGE: | |
| { | |
| unsigned long psv; | |
| psv = DIV_ROUND_CLOSEST(ndata->new_rate, gt_target_rate); | |
| if (!psv || | |
| abs(gt_target_rate - (ndata->new_rate / psv)) > MAX_F_ERR) | |
| return NOTIFY_BAD; | |
| psv--; | |
| /* prescaler within legal range? */ | |
| if (!FIELD_FIT(GT_CONTROL_PRESCALER_MASK, psv)) | |
| return NOTIFY_BAD; | |
| /* | |
| * store timer clock ctrl register so we can restore it in case | |
| * of an abort. | |
| */ | |
| gt_psv_bck = gt_read_presc(); | |
| gt_psv_new = psv; | |
| /* scale down: adjust divider in post-change notification */ | |
| if (ndata->new_rate < ndata->old_rate) | |
| return NOTIFY_DONE; | |
| /* scale up: adjust divider now - before frequency change */ | |
| gt_write_presc(psv); | |
| break; | |
| } | |
| case POST_RATE_CHANGE: | |
| /* scale up: pre-change notification did the adjustment */ | |
| if (ndata->new_rate > ndata->old_rate) | |
| return NOTIFY_OK; | |
| /* scale down: adjust divider now - after frequency change */ | |
| gt_write_presc(gt_psv_new); | |
| break; | |
| case ABORT_RATE_CHANGE: | |
| /* we have to undo the adjustment in case we scale up */ | |
| if (ndata->new_rate < ndata->old_rate) | |
| return NOTIFY_OK; | |
| /* restore original register value */ | |
| gt_write_presc(gt_psv_bck); | |
| break; | |
| default: | |
| return NOTIFY_DONE; | |
| } | |
| return NOTIFY_DONE; | |
| } | |
| struct gt_prescaler_config { | |
| const char *compatible; | |
| unsigned long prescaler; | |
| }; | |
| static const struct gt_prescaler_config gt_prescaler_configs[] = { | |
| /* | |
| * On am43 the global timer clock is a child of the clock used for CPU | |
| * OPPs, so the initial prescaler has to be compatible with all OPPs | |
| * which are 300, 600, 720, 800 and 1000 with a fixed divider of 2, this | |
| * gives us a GCD of 10. Initial frequency is 1000, so the prescaler is | |
| * 50. | |
| */ | |
| { .compatible = "ti,am43", .prescaler = 50 }, | |
| { .compatible = "xlnx,zynq-7000", .prescaler = 2 }, | |
| { .compatible = NULL } | |
| }; | |
| static unsigned long gt_get_initial_prescaler_value(struct device_node *np) | |
| { | |
| const struct gt_prescaler_config *config; | |
| if (CONFIG_ARM_GT_INITIAL_PRESCALER_VAL != 0) | |
| return CONFIG_ARM_GT_INITIAL_PRESCALER_VAL; | |
| for (config = gt_prescaler_configs; config->compatible; config++) { | |
| if (of_machine_is_compatible(config->compatible)) | |
| return config->prescaler; | |
| } | |
| return 1; | |
| } | |
| static int __init global_timer_of_register(struct device_node *np) | |
| { | |
| struct clk *gt_clk; | |
| static unsigned long gt_clk_rate; | |
| int err; | |
| unsigned long psv; | |
| /* | |
| * In A9 r2p0 the comparators for each processor with the global timer | |
| * fire when the timer value is greater than or equal to. In previous | |
| * revisions the comparators fired when the timer value was equal to. | |
| */ | |
| if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9 | |
| && (read_cpuid_id() & 0xf0000f) < 0x200000) { | |
| pr_warn("global-timer: non support for this cpu version.\n"); | |
| return -ENOSYS; | |
| } | |
| gt_ppi = irq_of_parse_and_map(np, 0); | |
| if (!gt_ppi) { | |
| pr_warn("global-timer: unable to parse irq\n"); | |
| return -EINVAL; | |
| } | |
| gt_base = of_iomap(np, 0); | |
| if (!gt_base) { | |
| pr_warn("global-timer: invalid base address\n"); | |
| return -ENXIO; | |
| } | |
| gt_clk = of_clk_get(np, 0); | |
| if (!IS_ERR(gt_clk)) { | |
| err = clk_prepare_enable(gt_clk); | |
| if (err) | |
| goto out_unmap; | |
| } else { | |
| pr_warn("global-timer: clk not found\n"); | |
| err = -EINVAL; | |
| goto out_unmap; | |
| } | |
| psv = gt_get_initial_prescaler_value(np); | |
| gt_clk_rate = clk_get_rate(gt_clk); | |
| gt_target_rate = gt_clk_rate / psv; | |
| gt_clk_rate_change_nb.notifier_call = | |
| gt_clk_rate_change_cb; | |
| err = clk_notifier_register(gt_clk, >_clk_rate_change_nb); | |
| if (err) { | |
| pr_warn("Unable to register clock notifier\n"); | |
| goto out_clk; | |
| } | |
| gt_evt = alloc_percpu(struct clock_event_device); | |
| if (!gt_evt) { | |
| pr_warn("global-timer: can't allocate memory\n"); | |
| err = -ENOMEM; | |
| goto out_clk_nb; | |
| } | |
| err = request_percpu_irq(gt_ppi, gt_clockevent_interrupt, | |
| "gt", gt_evt); | |
| if (err) { | |
| pr_warn("global-timer: can't register interrupt %d (%d)\n", | |
| gt_ppi, err); | |
| goto out_free; | |
| } | |
| /* Register and immediately configure the timer on the boot CPU */ | |
| err = gt_clocksource_init(psv); | |
| if (err) | |
| goto out_irq; | |
| err = cpuhp_setup_state(CPUHP_AP_ARM_GLOBAL_TIMER_STARTING, | |
| "clockevents/arm/global_timer:starting", | |
| gt_starting_cpu, gt_dying_cpu); | |
| if (err) | |
| goto out_irq; | |
| gt_delay_timer_init(); | |
| return 0; | |
| out_irq: | |
| free_percpu_irq(gt_ppi, gt_evt); | |
| out_free: | |
| free_percpu(gt_evt); | |
| out_clk_nb: | |
| clk_notifier_unregister(gt_clk, >_clk_rate_change_nb); | |
| out_clk: | |
| clk_disable_unprepare(gt_clk); | |
| out_unmap: | |
| iounmap(gt_base); | |
| WARN(err, "ARM Global timer register failed (%d)\n", err); | |
| return err; | |
| } | |
| /* Only tested on r2p2 and r3p0 */ | |
| TIMER_OF_DECLARE(arm_gt, "arm,cortex-a9-global-timer", | |
| global_timer_of_register); |