| // SPDX-License-Identifier: GPL-2.0 | |
| // Copyright (c) 2019 Nuvoton Technology corporation. | |
| #include <linux/auxiliary_bus.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/io.h> | |
| #include <linux/init.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/property.h> | |
| #include <linux/reboot.h> | |
| #include <linux/reset-controller.h> | |
| #include <linux/slab.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/regmap.h> | |
| #include <linux/of_address.h> | |
| #include <soc/nuvoton/clock-npcm8xx.h> | |
| /* NPCM7xx GCR registers */ | |
| #define NPCM_MDLR_OFFSET 0x7C | |
| #define NPCM7XX_MDLR_USBD0 BIT(9) | |
| #define NPCM7XX_MDLR_USBD1 BIT(8) | |
| #define NPCM7XX_MDLR_USBD2_4 BIT(21) | |
| #define NPCM7XX_MDLR_USBD5_9 BIT(22) | |
| /* NPCM8xx MDLR bits */ | |
| #define NPCM8XX_MDLR_USBD0_3 BIT(9) | |
| #define NPCM8XX_MDLR_USBD4_7 BIT(22) | |
| #define NPCM8XX_MDLR_USBD8 BIT(24) | |
| #define NPCM8XX_MDLR_USBD9 BIT(21) | |
| #define NPCM_USB1PHYCTL_OFFSET 0x140 | |
| #define NPCM_USB2PHYCTL_OFFSET 0x144 | |
| #define NPCM_USB3PHYCTL_OFFSET 0x148 | |
| #define NPCM_USBXPHYCTL_RS BIT(28) | |
| /* NPCM7xx Reset registers */ | |
| #define NPCM_SWRSTR 0x14 | |
| #define NPCM_SWRST BIT(2) | |
| #define NPCM_IPSRST1 0x20 | |
| #define NPCM_IPSRST1_USBD1 BIT(5) | |
| #define NPCM_IPSRST1_USBD2 BIT(8) | |
| #define NPCM_IPSRST1_USBD3 BIT(25) | |
| #define NPCM_IPSRST1_USBD4 BIT(22) | |
| #define NPCM_IPSRST1_USBD5 BIT(23) | |
| #define NPCM_IPSRST1_USBD6 BIT(24) | |
| #define NPCM_IPSRST2 0x24 | |
| #define NPCM_IPSRST2_USB_HOST BIT(26) | |
| #define NPCM_IPSRST3 0x34 | |
| #define NPCM_IPSRST3_USBD0 BIT(4) | |
| #define NPCM_IPSRST3_USBD7 BIT(5) | |
| #define NPCM_IPSRST3_USBD8 BIT(6) | |
| #define NPCM_IPSRST3_USBD9 BIT(7) | |
| #define NPCM_IPSRST3_USBPHY1 BIT(24) | |
| #define NPCM_IPSRST3_USBPHY2 BIT(25) | |
| #define NPCM_IPSRST4 0x74 | |
| #define NPCM_IPSRST4_USBPHY3 BIT(25) | |
| #define NPCM_IPSRST4_USB_HOST2 BIT(31) | |
| #define NPCM_RC_RESETS_PER_REG 32 | |
| #define NPCM_MASK_RESETS GENMASK(4, 0) | |
| enum { | |
| BMC_NPCM7XX = 0, | |
| BMC_NPCM8XX, | |
| }; | |
| static const u32 npxm7xx_ipsrst[] = {NPCM_IPSRST1, NPCM_IPSRST2, NPCM_IPSRST3}; | |
| static const u32 npxm8xx_ipsrst[] = {NPCM_IPSRST1, NPCM_IPSRST2, NPCM_IPSRST3, | |
| NPCM_IPSRST4}; | |
| struct npcm_reset_info { | |
| u32 bmc_id; | |
| u32 num_ipsrst; | |
| const u32 *ipsrst; | |
| }; | |
| static const struct npcm_reset_info npxm7xx_reset_info[] = { | |
| {.bmc_id = BMC_NPCM7XX, .num_ipsrst = 3, .ipsrst = npxm7xx_ipsrst}}; | |
| static const struct npcm_reset_info npxm8xx_reset_info[] = { | |
| {.bmc_id = BMC_NPCM8XX, .num_ipsrst = 4, .ipsrst = npxm8xx_ipsrst}}; | |
| struct npcm_rc_data { | |
| struct reset_controller_dev rcdev; | |
| const struct npcm_reset_info *info; | |
| struct regmap *gcr_regmap; | |
| u32 sw_reset_number; | |
| struct device *dev; | |
| void __iomem *base; | |
| spinlock_t lock; | |
| }; | |
| #define to_rc_data(p) container_of(p, struct npcm_rc_data, rcdev) | |
| static int npcm_rc_restart(struct sys_off_data *data) | |
| { | |
| struct npcm_rc_data *rc = data->cb_data; | |
| writel(NPCM_SWRST << rc->sw_reset_number, rc->base + NPCM_SWRSTR); | |
| mdelay(1000); | |
| pr_emerg("%s: unable to restart system\n", __func__); | |
| return NOTIFY_DONE; | |
| } | |
| static int npcm_rc_setclear_reset(struct reset_controller_dev *rcdev, | |
| unsigned long id, bool set) | |
| { | |
| struct npcm_rc_data *rc = to_rc_data(rcdev); | |
| unsigned int rst_bit = BIT(id & NPCM_MASK_RESETS); | |
| unsigned int ctrl_offset = id >> 8; | |
| unsigned long flags; | |
| u32 stat; | |
| spin_lock_irqsave(&rc->lock, flags); | |
| stat = readl(rc->base + ctrl_offset); | |
| if (set) | |
| writel(stat | rst_bit, rc->base + ctrl_offset); | |
| else | |
| writel(stat & ~rst_bit, rc->base + ctrl_offset); | |
| spin_unlock_irqrestore(&rc->lock, flags); | |
| return 0; | |
| } | |
| static int npcm_rc_assert(struct reset_controller_dev *rcdev, unsigned long id) | |
| { | |
| return npcm_rc_setclear_reset(rcdev, id, true); | |
| } | |
| static int npcm_rc_deassert(struct reset_controller_dev *rcdev, | |
| unsigned long id) | |
| { | |
| return npcm_rc_setclear_reset(rcdev, id, false); | |
| } | |
| static int npcm_rc_status(struct reset_controller_dev *rcdev, | |
| unsigned long id) | |
| { | |
| struct npcm_rc_data *rc = to_rc_data(rcdev); | |
| unsigned int rst_bit = BIT(id & NPCM_MASK_RESETS); | |
| unsigned int ctrl_offset = id >> 8; | |
| return (readl(rc->base + ctrl_offset) & rst_bit); | |
| } | |
| static int npcm_reset_xlate(struct reset_controller_dev *rcdev, | |
| const struct of_phandle_args *reset_spec) | |
| { | |
| struct npcm_rc_data *rc = to_rc_data(rcdev); | |
| unsigned int offset, bit; | |
| bool offset_found = false; | |
| int off_num; | |
| offset = reset_spec->args[0]; | |
| for (off_num = 0 ; off_num < rc->info->num_ipsrst ; off_num++) { | |
| if (offset == rc->info->ipsrst[off_num]) { | |
| offset_found = true; | |
| break; | |
| } | |
| } | |
| if (!offset_found) { | |
| dev_err(rcdev->dev, "Error reset register (0x%x)\n", offset); | |
| return -EINVAL; | |
| } | |
| bit = reset_spec->args[1]; | |
| if (bit >= NPCM_RC_RESETS_PER_REG) { | |
| dev_err(rcdev->dev, "Error reset number (%d)\n", bit); | |
| return -EINVAL; | |
| } | |
| return (offset << 8) | bit; | |
| } | |
| static const struct of_device_id npcm_rc_match[] = { | |
| { .compatible = "nuvoton,npcm750-reset", .data = &npxm7xx_reset_info}, | |
| { .compatible = "nuvoton,npcm845-reset", .data = &npxm8xx_reset_info}, | |
| { } | |
| }; | |
| static void npcm_usb_reset_npcm7xx(struct npcm_rc_data *rc) | |
| { | |
| u32 mdlr, iprst1, iprst2, iprst3; | |
| u32 ipsrst1_bits = 0; | |
| u32 ipsrst2_bits = NPCM_IPSRST2_USB_HOST; | |
| u32 ipsrst3_bits = 0; | |
| /* checking which USB device is enabled */ | |
| regmap_read(rc->gcr_regmap, NPCM_MDLR_OFFSET, &mdlr); | |
| if (!(mdlr & NPCM7XX_MDLR_USBD0)) | |
| ipsrst3_bits |= NPCM_IPSRST3_USBD0; | |
| if (!(mdlr & NPCM7XX_MDLR_USBD1)) | |
| ipsrst1_bits |= NPCM_IPSRST1_USBD1; | |
| if (!(mdlr & NPCM7XX_MDLR_USBD2_4)) | |
| ipsrst1_bits |= (NPCM_IPSRST1_USBD2 | | |
| NPCM_IPSRST1_USBD3 | | |
| NPCM_IPSRST1_USBD4); | |
| if (!(mdlr & NPCM7XX_MDLR_USBD0)) { | |
| ipsrst1_bits |= (NPCM_IPSRST1_USBD5 | | |
| NPCM_IPSRST1_USBD6); | |
| ipsrst3_bits |= (NPCM_IPSRST3_USBD7 | | |
| NPCM_IPSRST3_USBD8 | | |
| NPCM_IPSRST3_USBD9); | |
| } | |
| /* assert reset USB PHY and USB devices */ | |
| iprst1 = readl(rc->base + NPCM_IPSRST1); | |
| iprst2 = readl(rc->base + NPCM_IPSRST2); | |
| iprst3 = readl(rc->base + NPCM_IPSRST3); | |
| iprst1 |= ipsrst1_bits; | |
| iprst2 |= ipsrst2_bits; | |
| iprst3 |= (ipsrst3_bits | NPCM_IPSRST3_USBPHY1 | | |
| NPCM_IPSRST3_USBPHY2); | |
| writel(iprst1, rc->base + NPCM_IPSRST1); | |
| writel(iprst2, rc->base + NPCM_IPSRST2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| /* clear USB PHY RS bit */ | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB1PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, 0); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB2PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, 0); | |
| /* deassert reset USB PHY */ | |
| iprst3 &= ~(NPCM_IPSRST3_USBPHY1 | NPCM_IPSRST3_USBPHY2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| udelay(50); | |
| /* set USB PHY RS bit */ | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB1PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, NPCM_USBXPHYCTL_RS); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB2PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, NPCM_USBXPHYCTL_RS); | |
| /* deassert reset USB devices*/ | |
| iprst1 &= ~ipsrst1_bits; | |
| iprst2 &= ~ipsrst2_bits; | |
| iprst3 &= ~ipsrst3_bits; | |
| writel(iprst1, rc->base + NPCM_IPSRST1); | |
| writel(iprst2, rc->base + NPCM_IPSRST2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| } | |
| static void npcm_usb_reset_npcm8xx(struct npcm_rc_data *rc) | |
| { | |
| u32 mdlr, iprst1, iprst2, iprst3, iprst4; | |
| u32 ipsrst1_bits = 0; | |
| u32 ipsrst2_bits = NPCM_IPSRST2_USB_HOST; | |
| u32 ipsrst3_bits = 0; | |
| u32 ipsrst4_bits = NPCM_IPSRST4_USB_HOST2 | NPCM_IPSRST4_USBPHY3; | |
| /* checking which USB device is enabled */ | |
| regmap_read(rc->gcr_regmap, NPCM_MDLR_OFFSET, &mdlr); | |
| if (!(mdlr & NPCM8XX_MDLR_USBD0_3)) { | |
| ipsrst3_bits |= NPCM_IPSRST3_USBD0; | |
| ipsrst1_bits |= (NPCM_IPSRST1_USBD1 | | |
| NPCM_IPSRST1_USBD2 | | |
| NPCM_IPSRST1_USBD3); | |
| } | |
| if (!(mdlr & NPCM8XX_MDLR_USBD4_7)) { | |
| ipsrst1_bits |= (NPCM_IPSRST1_USBD4 | | |
| NPCM_IPSRST1_USBD5 | | |
| NPCM_IPSRST1_USBD6); | |
| ipsrst3_bits |= NPCM_IPSRST3_USBD7; | |
| } | |
| if (!(mdlr & NPCM8XX_MDLR_USBD8)) | |
| ipsrst3_bits |= NPCM_IPSRST3_USBD8; | |
| if (!(mdlr & NPCM8XX_MDLR_USBD9)) | |
| ipsrst3_bits |= NPCM_IPSRST3_USBD9; | |
| /* assert reset USB PHY and USB devices */ | |
| iprst1 = readl(rc->base + NPCM_IPSRST1); | |
| iprst2 = readl(rc->base + NPCM_IPSRST2); | |
| iprst3 = readl(rc->base + NPCM_IPSRST3); | |
| iprst4 = readl(rc->base + NPCM_IPSRST4); | |
| iprst1 |= ipsrst1_bits; | |
| iprst2 |= ipsrst2_bits; | |
| iprst3 |= (ipsrst3_bits | NPCM_IPSRST3_USBPHY1 | | |
| NPCM_IPSRST3_USBPHY2); | |
| iprst4 |= ipsrst4_bits; | |
| writel(iprst1, rc->base + NPCM_IPSRST1); | |
| writel(iprst2, rc->base + NPCM_IPSRST2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| writel(iprst4, rc->base + NPCM_IPSRST4); | |
| /* clear USB PHY RS bit */ | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB1PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, 0); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB2PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, 0); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB3PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, 0); | |
| /* deassert reset USB PHY */ | |
| iprst3 &= ~(NPCM_IPSRST3_USBPHY1 | NPCM_IPSRST3_USBPHY2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| iprst4 &= ~NPCM_IPSRST4_USBPHY3; | |
| writel(iprst4, rc->base + NPCM_IPSRST4); | |
| /* set USB PHY RS bit */ | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB1PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, NPCM_USBXPHYCTL_RS); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB2PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, NPCM_USBXPHYCTL_RS); | |
| regmap_update_bits(rc->gcr_regmap, NPCM_USB3PHYCTL_OFFSET, | |
| NPCM_USBXPHYCTL_RS, NPCM_USBXPHYCTL_RS); | |
| /* deassert reset USB devices*/ | |
| iprst1 &= ~ipsrst1_bits; | |
| iprst2 &= ~ipsrst2_bits; | |
| iprst3 &= ~ipsrst3_bits; | |
| iprst4 &= ~ipsrst4_bits; | |
| writel(iprst1, rc->base + NPCM_IPSRST1); | |
| writel(iprst2, rc->base + NPCM_IPSRST2); | |
| writel(iprst3, rc->base + NPCM_IPSRST3); | |
| writel(iprst4, rc->base + NPCM_IPSRST4); | |
| } | |
| /* | |
| * The following procedure should be observed in USB PHY, USB device and | |
| * USB host initialization at BMC boot | |
| */ | |
| static int npcm_usb_reset(struct platform_device *pdev, struct npcm_rc_data *rc) | |
| { | |
| struct device *dev = &pdev->dev; | |
| rc->gcr_regmap = syscon_regmap_lookup_by_phandle(dev->of_node, "nuvoton,sysgcr"); | |
| if (IS_ERR(rc->gcr_regmap)) { | |
| dev_warn(&pdev->dev, "Failed to find nuvoton,sysgcr property, please update the device tree\n"); | |
| dev_info(&pdev->dev, "Using nuvoton,npcm750-gcr for Poleg backward compatibility\n"); | |
| rc->gcr_regmap = syscon_regmap_lookup_by_compatible("nuvoton,npcm750-gcr"); | |
| if (IS_ERR(rc->gcr_regmap)) { | |
| dev_err(&pdev->dev, "Failed to find nuvoton,npcm750-gcr"); | |
| return PTR_ERR(rc->gcr_regmap); | |
| } | |
| } | |
| rc->info = device_get_match_data(dev); | |
| switch (rc->info->bmc_id) { | |
| case BMC_NPCM7XX: | |
| npcm_usb_reset_npcm7xx(rc); | |
| break; | |
| case BMC_NPCM8XX: | |
| npcm_usb_reset_npcm8xx(rc); | |
| break; | |
| default: | |
| return -ENODEV; | |
| } | |
| return 0; | |
| } | |
| static const struct reset_control_ops npcm_rc_ops = { | |
| .assert = npcm_rc_assert, | |
| .deassert = npcm_rc_deassert, | |
| .status = npcm_rc_status, | |
| }; | |
| static void npcm_clock_unregister_adev(void *_adev) | |
| { | |
| struct auxiliary_device *adev = _adev; | |
| auxiliary_device_delete(adev); | |
| auxiliary_device_uninit(adev); | |
| } | |
| static void npcm_clock_adev_release(struct device *dev) | |
| { | |
| struct auxiliary_device *adev = to_auxiliary_dev(dev); | |
| struct npcm_clock_adev *rdev = to_npcm_clock_adev(adev); | |
| kfree(rdev); | |
| } | |
| static struct auxiliary_device *npcm_clock_adev_alloc(struct npcm_rc_data *rst_data, char *clk_name) | |
| { | |
| struct npcm_clock_adev *rdev; | |
| struct auxiliary_device *adev; | |
| int ret; | |
| rdev = kzalloc_obj(*rdev); | |
| if (!rdev) | |
| return ERR_PTR(-ENOMEM); | |
| rdev->base = rst_data->base; | |
| adev = &rdev->adev; | |
| adev->name = clk_name; | |
| adev->dev.parent = rst_data->dev; | |
| adev->dev.release = npcm_clock_adev_release; | |
| adev->id = 555u; | |
| ret = auxiliary_device_init(adev); | |
| if (ret) { | |
| kfree(rdev); | |
| return ERR_PTR(ret); | |
| } | |
| return adev; | |
| } | |
| static int npcm8xx_clock_controller_register(struct npcm_rc_data *rst_data, char *clk_name) | |
| { | |
| struct auxiliary_device *adev; | |
| int ret; | |
| adev = npcm_clock_adev_alloc(rst_data, clk_name); | |
| if (IS_ERR(adev)) | |
| return PTR_ERR(adev); | |
| ret = auxiliary_device_add(adev); | |
| if (ret) { | |
| auxiliary_device_uninit(adev); | |
| return ret; | |
| } | |
| return devm_add_action_or_reset(rst_data->dev, npcm_clock_unregister_adev, adev); | |
| } | |
| static int npcm_rc_probe(struct platform_device *pdev) | |
| { | |
| struct npcm_rc_data *rc; | |
| int ret; | |
| rc = devm_kzalloc(&pdev->dev, sizeof(*rc), GFP_KERNEL); | |
| if (!rc) | |
| return -ENOMEM; | |
| rc->base = devm_platform_ioremap_resource(pdev, 0); | |
| if (IS_ERR(rc->base)) | |
| return PTR_ERR(rc->base); | |
| spin_lock_init(&rc->lock); | |
| rc->rcdev.owner = THIS_MODULE; | |
| rc->rcdev.ops = &npcm_rc_ops; | |
| rc->rcdev.of_node = pdev->dev.of_node; | |
| rc->rcdev.of_reset_n_cells = 2; | |
| rc->rcdev.of_xlate = npcm_reset_xlate; | |
| rc->dev = &pdev->dev; | |
| ret = devm_reset_controller_register(&pdev->dev, &rc->rcdev); | |
| if (ret) { | |
| dev_err(&pdev->dev, "unable to register device\n"); | |
| return ret; | |
| } | |
| if (npcm_usb_reset(pdev, rc)) | |
| dev_warn(&pdev->dev, "NPCM USB reset failed, can cause issues with UDC and USB host\n"); | |
| if (!of_property_read_u32(pdev->dev.of_node, "nuvoton,sw-reset-number", | |
| &rc->sw_reset_number)) { | |
| if (rc->sw_reset_number && rc->sw_reset_number < 5) { | |
| ret = devm_register_sys_off_handler(&pdev->dev, SYS_OFF_MODE_RESTART, 192, | |
| npcm_rc_restart, rc); | |
| if (ret) { | |
| dev_warn(&pdev->dev, "failed to register restart handler\n"); | |
| return ret; | |
| } | |
| } | |
| } | |
| switch (rc->info->bmc_id) { | |
| case BMC_NPCM8XX: | |
| return npcm8xx_clock_controller_register(rc, "clk-npcm8xx"); | |
| default: | |
| return 0; | |
| } | |
| } | |
| static struct platform_driver npcm_rc_driver = { | |
| .probe = npcm_rc_probe, | |
| .driver = { | |
| .name = "npcm-reset", | |
| .of_match_table = npcm_rc_match, | |
| .suppress_bind_attrs = true, | |
| }, | |
| }; | |
| builtin_platform_driver(npcm_rc_driver); |