| ====================================== | |
| HD-Audio Codec-Specific Mixer Controls | |
| ====================================== | |
| This file explains the codec-specific mixer controls. | |
| Realtek codecs | |
| -------------- | |
| Channel Mode | |
| This is an enum control to change the surround-channel setup, | |
| appears only when the surround channels are available. | |
| It gives the number of channels to be used, "2ch", "4ch", "6ch", | |
| and "8ch". According to the configuration, this also controls the | |
| jack-retasking of multi-I/O jacks. | |
| Auto-Mute Mode | |
| This is an enum control to change the auto-mute behavior of the | |
| headphone and line-out jacks. If built-in speakers and headphone | |
| and/or line-out jacks are available on a machine, this controls | |
| appears. | |
| When there are only either headphones or line-out jacks, it gives | |
| "Disabled" and "Enabled" state. When enabled, the speaker is muted | |
| automatically when a jack is plugged. | |
| When both headphone and line-out jacks are present, it gives | |
| "Disabled", "Speaker Only" and "Line-Out+Speaker". When | |
| speaker-only is chosen, plugging into a headphone or a line-out jack | |
| mutes the speakers, but not line-outs. When line-out+speaker is | |
| selected, plugging to a headphone jack mutes both speakers and | |
| line-outs. | |
| IDT/Sigmatel codecs | |
| ------------------- | |
| Analog Loopback | |
| This control enables/disables the analog-loopback circuit. This | |
| appears only when "loopback" is set to true in a codec hint | |
| (see HD-Audio.txt). Note that on some codecs the analog-loopback | |
| and the normal PCM playback are exclusive, i.e. when this is on, you | |
| won't hear any PCM stream. | |
| Swap Center/LFE | |
| Swaps the center and LFE channel order. Normally, the left | |
| corresponds to the center and the right to the LFE. When this is | |
| ON, the left to the LFE and the right to the center. | |
| Headphone as Line Out | |
| When this control is ON, treat the headphone jacks as line-out | |
| jacks. That is, the headphone won't auto-mute the other line-outs, | |
| and no HP-amp is set to the pins. | |
| Mic Jack Mode, Line Jack Mode, etc | |
| These enum controls the direction and the bias of the input jack | |
| pins. Depending on the jack type, it can set as "Mic In" and "Line | |
| In", for determining the input bias, or it can be set to "Line Out" | |
| when the pin is a multi-I/O jack for surround channels. | |
| VIA codecs | |
| ---------- | |
| Smart 5.1 | |
| An enum control to re-task the multi-I/O jacks for surround outputs. | |
| When it's ON, the corresponding input jacks (usually a line-in and a | |
| mic-in) are switched as the surround and the CLFE output jacks. | |
| Independent HP | |
| When this enum control is enabled, the headphone output is routed | |
| from an individual stream (the third PCM such as hw:0,2) instead of | |
| the primary stream. In the case the headphone DAC is shared with a | |
| side or a CLFE-channel DAC, the DAC is switched to the headphone | |
| automatically. | |
| Loopback Mixing | |
| An enum control to determine whether the analog-loopback route is | |
| enabled or not. When it's enabled, the analog-loopback is mixed to | |
| the front-channel. Also, the same route is used for the headphone | |
| and speaker outputs. As a side-effect, when this mode is set, the | |
| individual volume controls will be no longer available for | |
| headphones and speakers because there is only one DAC connected to a | |
| mixer widget. | |
| Dynamic Power-Control | |
| This control determines whether the dynamic power-control per jack | |
| detection is enabled or not. When enabled, the widgets power state | |
| (D0/D3) are changed dynamically depending on the jack plugging | |
| state for saving power consumptions. However, if your system | |
| doesn't provide a proper jack-detection, this won't work; in such a | |
| case, turn this control OFF. | |
| Jack Detect | |
| This control is provided only for VT1708 codec which gives no proper | |
| unsolicited event per jack plug. When this is on, the driver polls | |
| the jack detection so that the headphone auto-mute can work, while | |
| turning this off would reduce the power consumption. | |
| Conexant codecs | |
| --------------- | |
| Auto-Mute Mode | |
| See Reatek codecs. | |
| Analog codecs | |
| -------------- | |
| Channel Mode | |
| This is an enum control to change the surround-channel setup, | |
| appears only when the surround channels are available. | |
| It gives the number of channels to be used, "2ch", "4ch" and "6ch". | |
| According to the configuration, this also controls the | |
| jack-retasking of multi-I/O jacks. | |
| Independent HP | |
| When this enum control is enabled, the headphone output is routed | |
| from an individual stream (the third PCM such as hw:0,2) instead of | |
| the primary stream. |