| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * opp2430_data.c - old-style "OPP" table for OMAP2430 | |
| * | |
| * Copyright (C) 2005-2009 Texas Instruments, Inc. | |
| * Copyright (C) 2004-2009 Nokia Corporation | |
| * | |
| * Richard Woodruff <r-woodruff2@ti.com> | |
| * | |
| * The OMAP2 processor can be run at several discrete 'PRCM configurations'. | |
| * These configurations are characterized by voltage and speed for clocks. | |
| * The device is only validated for certain combinations. One way to express | |
| * these combinations is via the 'ratios' which the clocks operate with | |
| * respect to each other. These ratio sets are for a given voltage/DPLL | |
| * setting. All configurations can be described by a DPLL setting and a ratio. | |
| * | |
| * 2430 differs from 2420 in that there are no more phase synchronizers used. | |
| * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs | |
| * 2430 (iva2.1, NOdsp, mdm) | |
| * | |
| * XXX Missing voltage data. | |
| * XXX Missing 19.2MHz sys_clk rate sets. | |
| * | |
| * THe format described in this file is deprecated. Once a reasonable | |
| * OPP API exists, the data in this file should be converted to use it. | |
| * | |
| * This is technically part of the OMAP2xxx clock code. | |
| */ | |
| #include <linux/kernel.h> | |
| #include "opp2xxx.h" | |
| #include "sdrc.h" | |
| #include "clock.h" | |
| /* | |
| * Key dividers which make up a PRCM set. Ratios for a PRCM are mandated. | |
| * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU, | |
| * CM_CLKSEL_DSP, CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL, | |
| * CM_CLKSEL2_PLL, CM_CLKSEL_MDM | |
| * | |
| * Filling in table based on 2430-SDPs variants available. There are | |
| * quite a few more rate combinations which could be defined. | |
| * | |
| * When multiple values are defined the start up will try and choose | |
| * the fastest one. If a 'fast' value is defined, then automatically, | |
| * the /2 one should be included as it can be used. Generally having | |
| * more than one fast set does not make sense, as static timings need | |
| * to be changed to change the set. The exception is the bypass | |
| * setting which is available for low power bypass. | |
| * | |
| * Note: This table needs to be sorted, fastest to slowest. | |
| */ | |
| const struct prcm_config omap2430_rate_table[] = { | |
| /* PRCM #4 - ratio2 (ES2.1) - FAST */ | |
| {S13M, S798M, S399M, R2_CM_CLKSEL_MPU_VAL, /* 399MHz ARM */ | |
| R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL, | |
| R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, R2_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_133MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #2 - ratio1 (ES2) - FAST */ | |
| {S13M, S658M, S329M, R1_CM_CLKSEL_MPU_VAL, /* 330MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_165MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #5a - ratio1 - FAST */ | |
| {S13M, S532M, S266M, R1_CM_CLKSEL_MPU_VAL, /* 266MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_133MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #5b - ratio1 - FAST */ | |
| {S13M, S400M, S200M, R1_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_100MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #4 - ratio1 (ES2.1) - SLOW */ | |
| {S13M, S399M, S199M, R2_CM_CLKSEL_MPU_VAL, /* 200MHz ARM */ | |
| R2_CM_CLKSEL_DSP_VAL, R2_CM_CLKSEL_GFX_VAL, | |
| R2_CM_CLKSEL1_CORE_VAL, M4_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_1x_VAL, R2_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_133MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #2 - ratio1 (ES2) - SLOW */ | |
| {S13M, S329M, S164M, R1_CM_CLKSEL_MPU_VAL, /* 165MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M2_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_165MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #5a - ratio1 - SLOW */ | |
| {S13M, S266M, S133M, R1_CM_CLKSEL_MPU_VAL, /* 133MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M5A_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_133MHz, | |
| RATE_IN_243X}, | |
| /* PRCM #5b - ratio1 - SLOW*/ | |
| {S13M, S200M, S100M, R1_CM_CLKSEL_MPU_VAL, /* 100MHz ARM */ | |
| R1_CM_CLKSEL_DSP_VAL, R1_CM_CLKSEL_GFX_VAL, | |
| R1_CM_CLKSEL1_CORE_VAL, M5B_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_1x_VAL, R1_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_100MHz, | |
| RATE_IN_243X}, | |
| /* PRCM-boot/bypass */ | |
| {S13M, S13M, S13M, RB_CM_CLKSEL_MPU_VAL, /* 13MHz */ | |
| RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL, | |
| RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_13_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_BYPASS, | |
| RATE_IN_243X}, | |
| /* PRCM-boot/bypass */ | |
| {S12M, S12M, S12M, RB_CM_CLKSEL_MPU_VAL, /* 12MHz */ | |
| RB_CM_CLKSEL_DSP_VAL, RB_CM_CLKSEL_GFX_VAL, | |
| RB_CM_CLKSEL1_CORE_VAL, MB_CM_CLKSEL1_PLL_12_VAL, | |
| MX_CLKSEL2_PLL_2x_VAL, RB_CM_CLKSEL_MDM_VAL, | |
| SDRC_RFR_CTRL_BYPASS, | |
| RATE_IN_243X}, | |
| { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}, | |
| }; |