| ============================================= | |
| Linux voltage and current regulator framework | |
| ============================================= | |
| About | |
| ===== | |
| This framework is designed to provide a standard kernel interface to control | |
| voltage and current regulators. | |
| The intention is to allow systems to dynamically control regulator power output | |
| in order to save power and prolong battery life. This applies to both voltage | |
| regulators (where voltage output is controllable) and current sinks (where | |
| current limit is controllable). | |
| (C) 2008 Wolfson Microelectronics PLC. | |
| Author: Liam Girdwood <lrg@slimlogic.co.uk> | |
| Nomenclature | |
| ============ | |
| Some terms used in this document: | |
| - Regulator | |
| - Electronic device that supplies power to other devices. | |
| Most regulators can enable and disable their output while | |
| some can control their output voltage and or current. | |
| Input Voltage -> Regulator -> Output Voltage | |
| - PMIC | |
| - Power Management IC. An IC that contains numerous | |
| regulators and often contains other subsystems. | |
| - Consumer | |
| - Electronic device that is supplied power by a regulator. | |
| Consumers can be classified into two types:- | |
| Static: consumer does not change its supply voltage or | |
| current limit. It only needs to enable or disable its | |
| power supply. Its supply voltage is set by the hardware, | |
| bootloader, firmware or kernel board initialisation code. | |
| Dynamic: consumer needs to change its supply voltage or | |
| current limit to meet operation demands. | |
| - Power Domain | |
| - Electronic circuit that is supplied its input power by the | |
| output power of a regulator, switch or by another power | |
| domain. | |
| The supply regulator may be behind a switch(s). i.e.:: | |
| Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A] | |
| | | | |
| | +-> [Consumer B], [Consumer C] | |
| | | |
| +-> [Consumer D], [Consumer E] | |
| That is one regulator and three power domains: | |
| - Domain 1: Switch-1, Consumers D & E. | |
| - Domain 2: Switch-2, Consumers B & C. | |
| - Domain 3: Consumer A. | |
| and this represents a "supplies" relationship: | |
| Domain-1 --> Domain-2 --> Domain-3. | |
| A power domain may have regulators that are supplied power | |
| by other regulators. i.e.:: | |
| Regulator-1 -+-> Regulator-2 -+-> [Consumer A] | |
| | | |
| +-> [Consumer B] | |
| This gives us two regulators and two power domains: | |
| - Domain 1: Regulator-2, Consumer B. | |
| - Domain 2: Consumer A. | |
| and a "supplies" relationship: | |
| Domain-1 --> Domain-2 | |
| - Constraints | |
| - Constraints are used to define power levels for performance | |
| and hardware protection. Constraints exist at three levels: | |
| Regulator Level: This is defined by the regulator hardware | |
| operating parameters and is specified in the regulator | |
| datasheet. i.e. | |
| - voltage output is in the range 800mV -> 3500mV. | |
| - regulator current output limit is 20mA @ 5V but is | |
| 10mA @ 10V. | |
| Power Domain Level: This is defined in software by kernel | |
| level board initialisation code. It is used to constrain a | |
| power domain to a particular power range. i.e. | |
| - Domain-1 voltage is 3300mV | |
| - Domain-2 voltage is 1400mV -> 1600mV | |
| - Domain-3 current limit is 0mA -> 20mA. | |
| Consumer Level: This is defined by consumer drivers | |
| dynamically setting voltage or current limit levels. | |
| e.g. a consumer backlight driver asks for a current increase | |
| from 5mA to 10mA to increase LCD illumination. This passes | |
| to through the levels as follows :- | |
| Consumer: need to increase LCD brightness. Lookup and | |
| request next current mA value in brightness table (the | |
| consumer driver could be used on several different | |
| personalities based upon the same reference device). | |
| Power Domain: is the new current limit within the domain | |
| operating limits for this domain and system state (e.g. | |
| battery power, USB power) | |
| Regulator Domains: is the new current limit within the | |
| regulator operating parameters for input/output voltage. | |
| If the regulator request passes all the constraint tests | |
| then the new regulator value is applied. | |
| Design | |
| ====== | |
| The framework is designed and targeted at SoC based devices but may also be | |
| relevant to non SoC devices and is split into the following four interfaces:- | |
| 1. Consumer driver interface. | |
| This uses a similar API to the kernel clock interface in that consumer | |
| drivers can get and put a regulator (like they can with clocks atm) and | |
| get/set voltage, current limit, mode, enable and disable. This should | |
| allow consumers complete control over their supply voltage and current | |
| limit. This also compiles out if not in use so drivers can be reused in | |
| systems with no regulator based power control. | |
| See Documentation/power/regulator/consumer.rst | |
| 2. Regulator driver interface. | |
| This allows regulator drivers to register their regulators and provide | |
| operations to the core. It also has a notifier call chain for propagating | |
| regulator events to clients. | |
| See Documentation/power/regulator/regulator.rst | |
| 3. Machine interface. | |
| This interface is for machine specific code and allows the creation of | |
| voltage/current domains (with constraints) for each regulator. It can | |
| provide regulator constraints that will prevent device damage through | |
| overvoltage or overcurrent caused by buggy client drivers. It also | |
| allows the creation of a regulator tree whereby some regulators are | |
| supplied by others (similar to a clock tree). | |
| See Documentation/power/regulator/machine.rst | |
| 4. Userspace ABI. | |
| The framework also exports a lot of useful voltage/current/opmode data to | |
| userspace via sysfs. This could be used to help monitor device power | |
| consumption and status. | |
| See Documentation/ABI/testing/sysfs-class-regulator |