| // SPDX-License-Identifier: GPL-2.0+ |
| // Copyright (c) 2021 Facebook Inc. |
| /dts-v1/; |
| |
| #include "aspeed-g6.dtsi" |
| #include <dt-bindings/gpio/aspeed-gpio.h> |
| #include <dt-bindings/usb/pd.h> |
| #include <dt-bindings/leds/leds-pca955x.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/i2c/i2c.h> |
| |
| / { |
| model = "Facebook Bletchley BMC"; |
| compatible = "facebook,bletchley-bmc", "aspeed,ast2600"; |
| |
| aliases { |
| serial4 = &uart5; |
| }; |
| |
| chosen { |
| bootargs = "console=ttyS4,57600n8"; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x80000000>; |
| }; |
| |
| iio-hwmon { |
| compatible = "iio-hwmon"; |
| io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, |
| <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, |
| <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>, |
| <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>; |
| }; |
| |
| spi1_gpio: spi1-gpio { |
| compatible = "spi-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>; |
| gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>; |
| gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>; |
| num-chipselects = <1>; |
| cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>; |
| |
| tpm@0 { |
| compatible = "infineon,slb9670", "tcg,tpm_tis-spi"; |
| spi-max-frequency = <33000000>; |
| reg = <0>; |
| }; |
| }; |
| |
| switchphy: ethernet-phy@0 { |
| // Fixed link |
| }; |
| |
| front_gpio_leds { |
| compatible = "gpio-leds"; |
| sys_log_id { |
| default-state = "off"; |
| gpios = <&front_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| fan_gpio_leds { |
| compatible = "gpio-leds"; |
| fan0_blue { |
| retain-state-shutdown; |
| default-state = "on"; |
| gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>; |
| }; |
| fan1_blue { |
| retain-state-shutdown; |
| default-state = "on"; |
| gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>; |
| }; |
| fan2_blue { |
| retain-state-shutdown; |
| default-state = "on"; |
| gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>; |
| }; |
| fan3_blue { |
| retain-state-shutdown; |
| default-state = "on"; |
| gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>; |
| }; |
| fan0_amber { |
| retain-state-shutdown; |
| default-state = "off"; |
| gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>; |
| }; |
| fan1_amber { |
| retain-state-shutdown; |
| default-state = "off"; |
| gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>; |
| }; |
| fan2_amber { |
| retain-state-shutdown; |
| default-state = "off"; |
| gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>; |
| }; |
| fan3_amber { |
| retain-state-shutdown; |
| default-state = "off"; |
| gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| sled1_gpio_leds { |
| compatible = "gpio-leds"; |
| sled1_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled1_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| sled2_gpio_leds { |
| compatible = "gpio-leds"; |
| sled2_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled2_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| sled3_gpio_leds { |
| compatible = "gpio-leds"; |
| sled3_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled3_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| sled4_gpio_leds { |
| compatible = "gpio-leds"; |
| sled4_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled4_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| sled5_gpio_leds { |
| compatible = "gpio-leds"; |
| sled5_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled5_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| sled6_gpio_leds { |
| compatible = "gpio-leds"; |
| sled6_amber { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>; |
| }; |
| sled6_blue { |
| retain-state-shutdown; |
| default-state = "keep"; |
| gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| presence-sled1 { |
| label = "presence-sled1"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 2)>; |
| }; |
| presence-sled2 { |
| label = "presence-sled2"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 3)>; |
| }; |
| presence-sled3 { |
| label = "presence-sled3"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 4)>; |
| }; |
| presence-sled4 { |
| label = "presence-sled4"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 5)>; |
| }; |
| presence-sled5 { |
| label = "presence-sled5"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 6)>; |
| }; |
| presence-sled6 { |
| label = "presence-sled6"; |
| gpios = <&gpio0 ASPEED_GPIO(H, 7) GPIO_ACTIVE_LOW>; |
| linux,code = <ASPEED_GPIO(H, 7)>; |
| }; |
| }; |
| |
| vbus_sled1: vbus_sled1 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled1"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled1_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vbus_sled2: vbus_sled2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled2"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled2_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vbus_sled3: vbus_sled3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled3"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled3_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vbus_sled4: vbus_sled4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled4"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled4_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vbus_sled5: vbus_sled5 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled5"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled5_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| |
| vbus_sled6: vbus_sled6 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus_sled6"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&sled6_ioexp 1 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &mac2 { |
| status = "okay"; |
| phy-mode = "rgmii"; |
| phy-handle = <&switchphy>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rgmii3_default>; |
| |
| fixed-link { |
| speed = <1000>; |
| full-duplex; |
| }; |
| }; |
| |
| &fmc { |
| status = "okay"; |
| flash@0 { |
| status = "okay"; |
| m25p,fast-read; |
| label = "bmc"; |
| spi-max-frequency = <50000000>; |
| #include "openbmc-flash-layout-128.dtsi" |
| }; |
| flash@1 { |
| status = "okay"; |
| m25p,fast-read; |
| label = "alt-bmc"; |
| spi-max-frequency = <50000000>; |
| }; |
| }; |
| |
| &spi2 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_spi2_default>; |
| |
| flash@0 { |
| status = "okay"; |
| m25p,fast-read; |
| label = "pnor"; |
| spi-max-frequency = <50000000>; |
| }; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled1_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED1_SWD_MUX", "SLED1_XRES_SWD_N", |
| "SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN"; |
| }; |
| |
| sled1_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT", |
| "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT", |
| "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY", |
| "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1"; |
| }; |
| |
| sled1_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled1_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled1>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled2_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED2_SWD_MUX", "SLED2_XRES_SWD_N", |
| "SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN"; |
| }; |
| |
| sled2_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT", |
| "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT", |
| "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY", |
| "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2"; |
| }; |
| |
| sled2_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled2_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled2>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c2 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled3_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED3_SWD_MUX", "SLED3_XRES_SWD_N", |
| "SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN"; |
| }; |
| |
| sled3_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT", |
| "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT", |
| "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY", |
| "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3"; |
| }; |
| |
| sled3_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled3_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled3>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c3 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled4_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED4_SWD_MUX", "SLED4_XRES_SWD_N", |
| "SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN"; |
| }; |
| |
| sled4_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT", |
| "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT", |
| "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY", |
| "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4"; |
| }; |
| |
| sled4_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled4_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled4>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c4 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled5_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED5_SWD_MUX", "SLED5_XRES_SWD_N", |
| "SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN"; |
| }; |
| |
| sled5_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT", |
| "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT", |
| "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY", |
| "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5"; |
| }; |
| |
| sled5_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled5_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled5>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c5 { |
| status = "okay"; |
| ina230@45 { |
| compatible = "ti,ina230"; |
| reg = <0x45>; |
| shunt-resistor = <2000>; |
| }; |
| |
| mp5023@40 { |
| compatible = "mps,mp5023"; |
| reg = <0x40>; |
| }; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| sled6_ioexp41: pca9536@41 { |
| compatible = "nxp,pca9536"; |
| reg = <0x41>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLED6_SWD_MUX", "SLED6_XRES_SWD_N", |
| "SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN"; |
| }; |
| |
| sled6_ioexp: pca9539@76 { |
| compatible = "nxp,pca9539"; |
| reg = <0x76>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>; |
| |
| gpio-line-names = |
| "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT", |
| "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT", |
| "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY", |
| "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6"; |
| }; |
| |
| sled6_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| |
| sled6_fusb302: typec-portc@22 { |
| compatible = "fcs,fusb302"; |
| reg = <0x22>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>; |
| vbus-supply = <&vbus_sled6>; |
| |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "source"; |
| data-role = "host"; |
| pd-disable; |
| typec-power-opmode = "default"; |
| }; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c6 { |
| status = "okay"; |
| |
| eeprom@56 { |
| compatible = "atmel,24c64"; |
| reg = <0x56>; |
| }; |
| |
| rtc@51 { |
| /* in-chip rtc disabled, use external rtc (battery-backed) */ |
| compatible = "nxp,pcf85263"; |
| reg = <0x51>; |
| }; |
| }; |
| |
| &i2c7 { |
| status = "okay"; |
| |
| eeprom@54 { |
| compatible = "atmel,24c64"; |
| reg = <0x54>; |
| }; |
| }; |
| |
| &i2c9 { |
| status = "okay"; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| }; |
| |
| &i2c10 { |
| status = "okay"; |
| |
| tmp421@4f { |
| compatible = "ti,tmp421"; |
| reg = <0x4f>; |
| }; |
| |
| front_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "led-fault-identify","power-p5v-stby-good", |
| "power-p1v0-dvdd-good","power-p1v0-avdd-good", |
| "","","","", |
| "","","","", |
| "","","",""; |
| }; |
| }; |
| |
| &i2c12 { |
| status = "okay"; |
| |
| adm1278@11 { |
| compatible = "adi,adm1278"; |
| reg = <0x11>; |
| shunt-resistor-micro-ohms = <300>; |
| adi,volt-curr-sample-average = <128>; |
| adi,power-sample-average = <128>; |
| }; |
| |
| tmp421@4c { |
| compatible = "ti,tmp421"; |
| reg = <0x4c>; |
| }; |
| |
| tmp421@4d { |
| compatible = "ti,tmp421"; |
| reg = <0x4d>; |
| }; |
| |
| fan_leds: pca9552@67 { |
| compatible = "nxp,pca9552"; |
| reg = <0x67>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "presence-fan0","presence-fan1", |
| "presence-fan2","presence-fan3", |
| "power-fan0-good","power-fan1-good", |
| "power-fan2-good","power-fan3-good", |
| "","","","", |
| "","","",""; |
| }; |
| }; |
| |
| &i2c13 { |
| multi-master; |
| aspeed,hw-timeout-ms = <1000>; |
| status = "okay"; |
| |
| //USB Debug Connector |
| ipmb13@10 { |
| compatible = "ipmb-dev"; |
| reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; |
| i2c-protocol; |
| }; |
| }; |
| |
| &gpio0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_gpiov2_unbiased_default>; |
| |
| gpio-line-names = |
| /*A0-A7*/ "","","","","","","","", |
| /*B0-B7*/ "FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N", |
| "SEL_SPI2_MUX","SPI2_MUX1", |
| "SPI2_MUX2","SPI2_MUX3", |
| "","FUSB302_SLED3_INT_N", |
| /*C0-C7*/ "","","","","","","","", |
| /*D0-D7*/ "","","","","","","","", |
| /*E0-E7*/ "","","","","","","","", |
| /*F0-F7*/ "BMC_SLED1_STCK","BMC_SLED2_STCK", |
| "BMC_SLED3_STCK","BMC_SLED4_STCK", |
| "BMC_SLED5_STCK","BMC_SLED6_STCK", |
| "","", |
| /*G0-G7*/ "BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL", |
| "PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","", |
| /*H0-H7*/ "presence-riser1","presence-riser2", |
| "presence-sled1","presence-sled2", |
| "presence-sled3","presence-sled4", |
| "presence-sled5","presence-sled6", |
| /*I0-I7*/ "REV_ID0","", |
| "REV_ID1","REV_ID2", |
| "","BSM_FLASH_WP_STATUS", |
| "BMC_TPM_PRES_N","FUSB302_SLED6_INT_N", |
| /*J0-J7*/ "","","","","","","","", |
| /*K0-K7*/ "","","","","","","","", |
| /*L0-L7*/ "","","","","","BMC_RTC_INT","","", |
| /*M0-M7*/ "ALERT_SLED1_N","ALERT_SLED2_N", |
| "ALERT_SLED3_N","ALERT_SLED4_N", |
| "ALERT_SLED5_N","ALERT_SLED6_N", |
| "","USB_DEBUG_PWR_BTN_N", |
| /*N0-N7*/ "LED_POSTCODE_0","LED_POSTCODE_1", |
| "LED_POSTCODE_2","LED_POSTCODE_3", |
| "LED_POSTCODE_4","LED_POSTCODE_5", |
| "LED_POSTCODE_6","LED_POSTCODE_7", |
| /*O0-O7*/ "","","","", |
| "","BOARD_ID0","BOARD_ID1","BOARD_ID2", |
| /*P0-P7*/ "","","","","","","","BMC_HEARTBEAT", |
| /*Q0-Q7*/ "","","","","","","","", |
| /*R0-R7*/ "","","","","","","","", |
| /*S0-S7*/ "","","","BAT_DETECT", |
| "BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N", |
| /*T0-T7*/ "","","","","","","","", |
| /*U0-U7*/ "","","","","","","","", |
| /*V0-V7*/ "PWRGD_CNS_PSU","RST_BMC_MVL_N", |
| "P12V_AUX_ALERT1_N","PSU_PRSNT", |
| "USB2_SEL0_A","USB2_SEL1_A", |
| "USB2_SEL0_B","USB2_SEL1_B", |
| /*W0-W7*/ "RST_FRONT_IOEXP_N","","","","","","","", |
| /*X0-X7*/ "","","","","","","","", |
| /*Y0-Y7*/ "BMC_SELF_HW_RST","BSM_PRSNT_N", |
| "BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N", |
| "","","","", |
| /*Z0-Z7*/ "","","","","","","",""; |
| }; |
| |
| &adc0 { |
| vref = <1800>; |
| status = "okay"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default |
| &pinctrl_adc2_default &pinctrl_adc3_default |
| &pinctrl_adc4_default &pinctrl_adc5_default |
| &pinctrl_adc6_default &pinctrl_adc7_default>; |
| }; |
| |
| &adc1 { |
| vref = <2500>; |
| status = "okay"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default |
| &pinctrl_adc10_default &pinctrl_adc11_default |
| &pinctrl_adc12_default &pinctrl_adc13_default |
| &pinctrl_adc14_default &pinctrl_adc15_default>; |
| }; |
| |
| &mdio0 { |
| status = "okay"; |
| /* TODO: Add Marvell 88E6191X */ |
| }; |
| |
| &mdio3 { |
| status = "okay"; |
| /* TODO: Add Marvell 88X3310 */ |
| }; |
| |
| &ehci0 { |
| status = "okay"; |
| }; |
| |
| &ehci1 { |
| status = "okay"; |
| }; |
| |
| &emmc_controller { |
| status = "okay"; |
| }; |
| |
| &emmc { |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| pinctrl_gpiov2_unbiased_default: gpiov2 { |
| pins = "AD14"; |
| bias-disable; |
| }; |
| }; |
| |
| &wdt1 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdtrst1_default>; |
| aspeed,reset-type = "soc"; |
| aspeed,external-signal; |
| aspeed,ext-push-pull; |
| aspeed,ext-active-high; |
| aspeed,ext-pulse-duration = <256>; |
| }; |
