| // SPDX-License-Identifier: GPL-2.0 | |
| /***************************************************************************/ | |
| /* | |
| * m528x.c -- platform support for ColdFire 528x based boards | |
| * | |
| * Sub-architcture dependent initialization code for the Freescale | |
| * 5280, 5281 and 5282 CPUs. | |
| * | |
| * Copyright (C) 1999-2003, Greg Ungerer (gerg@snapgear.com) | |
| * Copyright (C) 2001-2003, SnapGear Inc. (www.snapgear.com) | |
| */ | |
| /***************************************************************************/ | |
| #include <linux/clkdev.h> | |
| #include <linux/kernel.h> | |
| #include <linux/param.h> | |
| #include <linux/init.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/io.h> | |
| #include <asm/machdep.h> | |
| #include <asm/coldfire.h> | |
| #include <asm/mcfsim.h> | |
| #include <asm/mcfuart.h> | |
| #include <asm/mcfclk.h> | |
| /***************************************************************************/ | |
| DEFINE_CLK(pll, "pll.0", MCF_CLK); | |
| DEFINE_CLK(sys, "sys.0", MCF_BUSCLK); | |
| static struct clk_lookup m528x_clk_lookup[] = { | |
| CLKDEV_INIT(NULL, "pll.0", &clk_pll), | |
| CLKDEV_INIT(NULL, "sys.0", &clk_sys), | |
| CLKDEV_INIT("mcfpit.0", NULL, &clk_pll), | |
| CLKDEV_INIT("mcfpit.1", NULL, &clk_pll), | |
| CLKDEV_INIT("mcfpit.2", NULL, &clk_pll), | |
| CLKDEV_INIT("mcfpit.3", NULL, &clk_pll), | |
| CLKDEV_INIT("mcfuart.0", NULL, &clk_sys), | |
| CLKDEV_INIT("mcfuart.1", NULL, &clk_sys), | |
| CLKDEV_INIT("mcfuart.2", NULL, &clk_sys), | |
| CLKDEV_INIT("mcfqspi.0", NULL, &clk_sys), | |
| CLKDEV_INIT("fec.0", NULL, &clk_sys), | |
| CLKDEV_INIT("imx1-i2c.0", NULL, &clk_sys), | |
| }; | |
| /***************************************************************************/ | |
| static void __init m528x_qspi_init(void) | |
| { | |
| #if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) | |
| /* setup Port QS for QSPI with gpio CS control */ | |
| mcf_write8(0x07, MCFGPIO_PQSPAR); | |
| #endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */ | |
| } | |
| /***************************************************************************/ | |
| static void __init m528x_i2c_init(void) | |
| { | |
| #if IS_ENABLED(CONFIG_I2C_IMX) | |
| u16 paspar; | |
| /* setup Port AS Pin Assignment Register for I2C */ | |
| /* set PASPA0 to SCL and PASPA1 to SDA */ | |
| paspar = mcf_read16(MCFGPIO_PASPAR); | |
| paspar |= 0xF; | |
| mcf_write16(paspar, MCFGPIO_PASPAR); | |
| #endif /* IS_ENABLED(CONFIG_I2C_IMX) */ | |
| } | |
| /***************************************************************************/ | |
| static void __init m528x_uarts_init(void) | |
| { | |
| u8 port; | |
| /* make sure PUAPAR is set for UART0 and UART1 */ | |
| port = mcf_read8(MCFGPIO_PUAPAR); | |
| port |= 0x03 | (0x03 << 2); | |
| mcf_write8(port, MCFGPIO_PUAPAR); | |
| } | |
| /***************************************************************************/ | |
| static void __init m528x_fec_init(void) | |
| { | |
| u16 v16; | |
| /* Set multi-function pins to ethernet mode for fec0 */ | |
| v16 = mcf_read16(MCFGPIO_PASPAR); | |
| mcf_write16(v16 | 0xf00, MCFGPIO_PASPAR); | |
| mcf_write8(0xc0, MCFGPIO_PEHLPAR); | |
| } | |
| /***************************************************************************/ | |
| #ifdef CONFIG_WILDFIRE | |
| void wildfire_halt(void) | |
| { | |
| mcf_write8(0, 0x30000007); | |
| mcf_write8(0x2, 0x30000007); | |
| } | |
| #endif | |
| #ifdef CONFIG_WILDFIREMOD | |
| void wildfiremod_halt(void) | |
| { | |
| printk(KERN_INFO "WildFireMod hibernating...\n"); | |
| /* Set portE.5 to Digital IO */ | |
| mcf_write16(mcf_read16(MCFGPIO_PEPAR) & ~(1 << (5 * 2)), MCFGPIO_PEPAR); | |
| /* Make portE.5 an output */ | |
| mcf_write8(mcf_read8(MCFGPIO_PDDR_E) | (1 << 5), MCFGPIO_PDDR_E); | |
| /* Now toggle portE.5 from low to high */ | |
| mcf_write8(mcf_read8(MCFGPIO_PODR_E) & ~(1 << 5), MCFGPIO_PODR_E); | |
| mcf_write8(mcf_read8(MCFGPIO_PODR_E) | (1 << 5), MCFGPIO_PODR_E); | |
| printk(KERN_EMERG "Failed to hibernate. Halting!\n"); | |
| } | |
| #endif | |
| void __init config_BSP(char *commandp, int size) | |
| { | |
| #ifdef CONFIG_WILDFIRE | |
| mach_halt = wildfire_halt; | |
| #endif | |
| #ifdef CONFIG_WILDFIREMOD | |
| mach_halt = wildfiremod_halt; | |
| #endif | |
| mach_sched_init = hw_timer_init; | |
| m528x_uarts_init(); | |
| m528x_fec_init(); | |
| m528x_qspi_init(); | |
| m528x_i2c_init(); | |
| clkdev_add_table(m528x_clk_lookup, ARRAY_SIZE(m528x_clk_lookup)); | |
| } | |
| /***************************************************************************/ |