| // SPDX-License-Identifier: GPL-2.0 | |
| /***************************************************************************/ | |
| /* | |
| * m5307.c -- platform support for ColdFire 5307 based boards | |
| * | |
| * Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com) | |
| * Copyright (C) 2000, Lineo (www.lineo.com) | |
| */ | |
| /***************************************************************************/ | |
| #include <linux/clkdev.h> | |
| #include <linux/kernel.h> | |
| #include <linux/param.h> | |
| #include <linux/init.h> | |
| #include <linux/io.h> | |
| #include <asm/machdep.h> | |
| #include <asm/coldfire.h> | |
| #include <asm/mcfsim.h> | |
| #include <asm/mcfwdebug.h> | |
| #include <asm/mcfclk.h> | |
| /***************************************************************************/ | |
| /* | |
| * Some platforms need software versions of the GPIO data registers. | |
| */ | |
| unsigned short ppdata; | |
| unsigned char ledbank = 0xff; | |
| /***************************************************************************/ | |
| DEFINE_CLK(pll, "pll.0", MCF_CLK); | |
| DEFINE_CLK(sys, "sys.0", MCF_BUSCLK); | |
| static struct clk_lookup m5307_clk_lookup[] = { | |
| CLKDEV_INIT(NULL, "pll.0", &clk_pll), | |
| CLKDEV_INIT(NULL, "sys.0", &clk_sys), | |
| CLKDEV_INIT("mcftmr.0", NULL, &clk_sys), | |
| CLKDEV_INIT("mcftmr.1", NULL, &clk_sys), | |
| CLKDEV_INIT("mcfuart.0", NULL, &clk_sys), | |
| CLKDEV_INIT("mcfuart.1", NULL, &clk_sys), | |
| CLKDEV_INIT("imx1-i2c.0", NULL, &clk_sys), | |
| }; | |
| /***************************************************************************/ | |
| static void __init m5307_i2c_init(void) | |
| { | |
| #if IS_ENABLED(CONFIG_I2C_IMX) | |
| mcf_write8(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL5 | MCFSIM_ICR_PRI0, | |
| MCFSIM_I2CICR); | |
| mcf_mapirq2imr(MCF_IRQ_I2C0, MCFINTC_I2C); | |
| #endif /* IS_ENABLED(CONFIG_I2C_IMX) */ | |
| } | |
| /***************************************************************************/ | |
| void __init config_BSP(char *commandp, int size) | |
| { | |
| #if defined(CONFIG_NETtel) || \ | |
| defined(CONFIG_SECUREEDGEMP3) || defined(CONFIG_CLEOPATRA) | |
| /* Copy command line from FLASH to local buffer... */ | |
| memcpy(commandp, (char *) 0xf0004000, size); | |
| commandp[size-1] = 0; | |
| #endif | |
| mach_sched_init = hw_timer_init; | |
| /* Only support the external interrupts on their primary level */ | |
| mcf_mapirq2imr(25, MCFINTC_EINT1); | |
| mcf_mapirq2imr(27, MCFINTC_EINT3); | |
| mcf_mapirq2imr(29, MCFINTC_EINT5); | |
| mcf_mapirq2imr(31, MCFINTC_EINT7); | |
| #ifdef CONFIG_BDM_DISABLE | |
| /* | |
| * Disable the BDM clocking. This also turns off most of the rest of | |
| * the BDM device. This is good for EMC reasons. This option is not | |
| * incompatible with the memory protection option. | |
| */ | |
| wdebug(MCFDEBUG_CSR, MCFDEBUG_CSR_PSTCLK); | |
| #endif | |
| m5307_i2c_init(); | |
| clkdev_add_table(m5307_clk_lookup, ARRAY_SIZE(m5307_clk_lookup)); | |
| } | |
| /***************************************************************************/ |