| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * BME680 - SPI Driver | |
| * | |
| * Copyright (C) 2018 Himanshu Jha <himanshujha199640@gmail.com> | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/regmap.h> | |
| #include <linux/spi/spi.h> | |
| #include "bme680.h" | |
| struct bme680_spi_bus_context { | |
| struct spi_device *spi; | |
| u8 current_page; | |
| }; | |
| /* | |
| * In SPI mode there are only 7 address bits, a "page" register determines | |
| * which part of the 8-bit range is active. This function looks at the address | |
| * and writes the page selection bit if needed | |
| */ | |
| static int bme680_regmap_spi_select_page( | |
| struct bme680_spi_bus_context *ctx, u8 reg) | |
| { | |
| struct spi_device *spi = ctx->spi; | |
| int ret; | |
| u8 buf[2]; | |
| u8 page = (reg & 0x80) ? 0 : 1; /* Page "1" is low range */ | |
| if (page == ctx->current_page) | |
| return 0; | |
| /* | |
| * Data sheet claims we're only allowed to change bit 4, so we must do | |
| * a read-modify-write on each and every page select | |
| */ | |
| buf[0] = BME680_REG_STATUS; | |
| ret = spi_write_then_read(spi, buf, 1, buf + 1, 1); | |
| if (ret < 0) { | |
| dev_err(&spi->dev, "failed to set page %u\n", page); | |
| return ret; | |
| } | |
| buf[0] = BME680_REG_STATUS; | |
| if (page) | |
| buf[1] |= BME680_SPI_MEM_PAGE_BIT; | |
| else | |
| buf[1] &= ~BME680_SPI_MEM_PAGE_BIT; | |
| ret = spi_write(spi, buf, 2); | |
| if (ret < 0) { | |
| dev_err(&spi->dev, "failed to set page %u\n", page); | |
| return ret; | |
| } | |
| ctx->current_page = page; | |
| return 0; | |
| } | |
| static int bme680_regmap_spi_write(void *context, const void *data, | |
| size_t count) | |
| { | |
| struct bme680_spi_bus_context *ctx = context; | |
| struct spi_device *spi = ctx->spi; | |
| int ret; | |
| u8 buf[2]; | |
| memcpy(buf, data, 2); | |
| ret = bme680_regmap_spi_select_page(ctx, buf[0]); | |
| if (ret) | |
| return ret; | |
| /* | |
| * The SPI register address (= full register address without bit 7) | |
| * and the write command (bit7 = RW = '0') | |
| */ | |
| buf[0] &= ~0x80; | |
| return spi_write(spi, buf, 2); | |
| } | |
| static int bme680_regmap_spi_read(void *context, const void *reg, | |
| size_t reg_size, void *val, size_t val_size) | |
| { | |
| struct bme680_spi_bus_context *ctx = context; | |
| struct spi_device *spi = ctx->spi; | |
| int ret; | |
| u8 addr = *(const u8 *)reg; | |
| ret = bme680_regmap_spi_select_page(ctx, addr); | |
| if (ret) | |
| return ret; | |
| addr |= 0x80; /* bit7 = RW = '1' */ | |
| return spi_write_then_read(spi, &addr, 1, val, val_size); | |
| } | |
| static const struct regmap_bus bme680_regmap_bus = { | |
| .write = bme680_regmap_spi_write, | |
| .read = bme680_regmap_spi_read, | |
| .reg_format_endian_default = REGMAP_ENDIAN_BIG, | |
| .val_format_endian_default = REGMAP_ENDIAN_BIG, | |
| }; | |
| static int bme680_spi_probe(struct spi_device *spi) | |
| { | |
| const struct spi_device_id *id = spi_get_device_id(spi); | |
| struct bme680_spi_bus_context *bus_context; | |
| struct regmap *regmap; | |
| bus_context = devm_kzalloc_obj(&spi->dev, *bus_context); | |
| if (!bus_context) | |
| return -ENOMEM; | |
| bus_context->spi = spi; | |
| bus_context->current_page = 0xff; /* Undefined on warm boot */ | |
| regmap = devm_regmap_init(&spi->dev, &bme680_regmap_bus, | |
| bus_context, &bme680_regmap_config); | |
| if (IS_ERR(regmap)) | |
| return dev_err_probe(&spi->dev, PTR_ERR(regmap), | |
| "Failed to register spi regmap\n"); | |
| return bme680_core_probe(&spi->dev, regmap, id->name); | |
| } | |
| static const struct spi_device_id bme680_spi_id[] = { | |
| { .name = "bme680" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(spi, bme680_spi_id); | |
| static const struct of_device_id bme680_of_spi_match[] = { | |
| { .compatible = "bosch,bme680", }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, bme680_of_spi_match); | |
| static struct spi_driver bme680_spi_driver = { | |
| .driver = { | |
| .name = "bme680_spi", | |
| .of_match_table = bme680_of_spi_match, | |
| .pm = pm_ptr(&bme680_dev_pm_ops), | |
| }, | |
| .probe = bme680_spi_probe, | |
| .id_table = bme680_spi_id, | |
| }; | |
| module_spi_driver(bme680_spi_driver); | |
| MODULE_AUTHOR("Himanshu Jha <himanshujha199640@gmail.com>"); | |
| MODULE_DESCRIPTION("Bosch BME680 SPI driver"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_IMPORT_NS("IIO_BME680"); |