| // SPDX-License-Identifier: GPL-2.0+ |
| // |
| // Freescale ALSA SoC Digital Audio Interface (SAI) driver. |
| // |
| // Copyright 2012-2015 Freescale Semiconductor, Inc. |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dmaengine.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/pm_qos.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regmap.h> |
| #include <linux/slab.h> |
| #include <linux/time.h> |
| #include <sound/core.h> |
| #include <sound/dmaengine_pcm.h> |
| #include <sound/pcm_params.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/mfd/syscon/imx6q-iomuxc-gpr.h> |
| |
| #include "fsl_sai.h" |
| #include "fsl_utils.h" |
| #include "imx-pcm.h" |
| |
| #define FSL_SAI_FLAGS (FSL_SAI_CSR_SEIE |\ |
| FSL_SAI_CSR_FEIE) |
| |
| static const unsigned int fsl_sai_rates[] = { |
| 8000, 11025, 12000, 16000, 22050, |
| 24000, 32000, 44100, 48000, 64000, |
| 88200, 96000, 176400, 192000, 352800, |
| 384000, 705600, 768000, 1411200, 2822400, |
| }; |
| |
| static const struct snd_pcm_hw_constraint_list fsl_sai_rate_constraints = { |
| .count = ARRAY_SIZE(fsl_sai_rates), |
| .list = fsl_sai_rates, |
| }; |
| |
| /** |
| * fsl_sai_dir_is_synced - Check if stream is synced by the opposite stream |
| * |
| * SAI supports synchronous mode using bit/frame clocks of either Transmitter's |
| * or Receiver's for both streams. This function is used to check if clocks of |
| * the stream's are synced by the opposite stream. |
| * |
| * @sai: SAI context |
| * @dir: stream direction |
| */ |
| static inline bool fsl_sai_dir_is_synced(struct fsl_sai *sai, int dir) |
| { |
| int adir = (dir == TX) ? RX : TX; |
| |
| /* current dir in async mode while opposite dir in sync mode */ |
| return !sai->synchronous[dir] && sai->synchronous[adir]; |
| } |
| |
| static struct pinctrl_state *fsl_sai_get_pins_state(struct fsl_sai *sai, u32 bclk) |
| { |
| struct pinctrl_state *state = NULL; |
| |
| if (sai->is_pdm_mode) { |
| /* DSD512@44.1kHz, DSD512@48kHz */ |
| if (bclk >= 22579200) |
| state = pinctrl_lookup_state(sai->pinctrl, "dsd512"); |
| |
| /* Get default DSD state */ |
| if (IS_ERR_OR_NULL(state)) |
| state = pinctrl_lookup_state(sai->pinctrl, "dsd"); |
| } else { |
| /* 706k32b2c, 768k32b2c, etc */ |
| if (bclk >= 45158400) |
| state = pinctrl_lookup_state(sai->pinctrl, "pcm_b2m"); |
| } |
| |
| /* Get default state */ |
| if (IS_ERR_OR_NULL(state)) |
| state = pinctrl_lookup_state(sai->pinctrl, "default"); |
| |
| return state; |
| } |
| |
| static irqreturn_t fsl_sai_isr(int irq, void *devid) |
| { |
| struct fsl_sai *sai = (struct fsl_sai *)devid; |
| unsigned int ofs = sai->soc_data->reg_offset; |
| struct device *dev = &sai->pdev->dev; |
| u32 flags, xcsr, mask; |
| irqreturn_t iret = IRQ_NONE; |
| |
| /* |
| * Both IRQ status bits and IRQ mask bits are in the xCSR but |
| * different shifts. And we here create a mask only for those |
| * IRQs that we activated. |
| */ |
| mask = (FSL_SAI_FLAGS >> FSL_SAI_CSR_xIE_SHIFT) << FSL_SAI_CSR_xF_SHIFT; |
| |
| /* Tx IRQ */ |
| regmap_read(sai->regmap, FSL_SAI_TCSR(ofs), &xcsr); |
| flags = xcsr & mask; |
| |
| if (flags) |
| iret = IRQ_HANDLED; |
| else |
| goto irq_rx; |
| |
| if (flags & FSL_SAI_CSR_WSF) |
| dev_dbg(dev, "isr: Start of Tx word detected\n"); |
| |
| if (flags & FSL_SAI_CSR_SEF) |
| dev_dbg(dev, "isr: Tx Frame sync error detected\n"); |
| |
| if (flags & FSL_SAI_CSR_FEF) |
| dev_dbg(dev, "isr: Transmit underrun detected\n"); |
| |
| if (flags & FSL_SAI_CSR_FWF) |
| dev_dbg(dev, "isr: Enabled transmit FIFO is empty\n"); |
| |
| if (flags & FSL_SAI_CSR_FRF) |
| dev_dbg(dev, "isr: Transmit FIFO watermark has been reached\n"); |
| |
| flags &= FSL_SAI_CSR_xF_W_MASK; |
| xcsr &= ~FSL_SAI_CSR_xF_MASK; |
| |
| if (flags) |
| regmap_write(sai->regmap, FSL_SAI_TCSR(ofs), flags | xcsr); |
| |
| irq_rx: |
| /* Rx IRQ */ |
| regmap_read(sai->regmap, FSL_SAI_RCSR(ofs), &xcsr); |
| flags = xcsr & mask; |
| |
| if (flags) |
| iret = IRQ_HANDLED; |
| else |
| goto out; |
| |
| if (flags & FSL_SAI_CSR_WSF) |
| dev_dbg(dev, "isr: Start of Rx word detected\n"); |
| |
| if (flags & FSL_SAI_CSR_SEF) |
| dev_dbg(dev, "isr: Rx Frame sync error detected\n"); |
| |
| if (flags & FSL_SAI_CSR_FEF) |
| dev_dbg(dev, "isr: Receive overflow detected\n"); |
| |
| if (flags & FSL_SAI_CSR_FWF) |
| dev_dbg(dev, "isr: Enabled receive FIFO is full\n"); |
| |
| if (flags & FSL_SAI_CSR_FRF) |
| dev_dbg(dev, "isr: Receive FIFO watermark has been reached\n"); |
| |
| flags &= FSL_SAI_CSR_xF_W_MASK; |
| xcsr &= ~FSL_SAI_CSR_xF_MASK; |
| |
| if (flags) |
| regmap_write(sai->regmap, FSL_SAI_RCSR(ofs), flags | xcsr); |
| |
| out: |
| return iret; |
| } |
| |
| static int fsl_sai_set_dai_tdm_slot(struct snd_soc_dai *cpu_dai, u32 tx_mask, |
| u32 rx_mask, int slots, int slot_width) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| |
| sai->slots = slots; |
| sai->slot_width = slot_width; |
| |
| return 0; |
| } |
| |
| static int fsl_sai_set_dai_bclk_ratio(struct snd_soc_dai *dai, |
| unsigned int ratio) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(dai); |
| |
| sai->bclk_ratio = ratio; |
| |
| return 0; |
| } |
| |
| static int fsl_sai_set_dai_sysclk_tr(struct snd_soc_dai *cpu_dai, |
| int clk_id, unsigned int freq, bool tx) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| u32 val_cr2 = 0; |
| |
| switch (clk_id) { |
| case FSL_SAI_CLK_BUS: |
| val_cr2 |= FSL_SAI_CR2_MSEL_BUS; |
| break; |
| case FSL_SAI_CLK_MAST1: |
| val_cr2 |= FSL_SAI_CR2_MSEL_MCLK1; |
| break; |
| case FSL_SAI_CLK_MAST2: |
| val_cr2 |= FSL_SAI_CR2_MSEL_MCLK2; |
| break; |
| case FSL_SAI_CLK_MAST3: |
| val_cr2 |= FSL_SAI_CR2_MSEL_MCLK3; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR2(tx, ofs), |
| FSL_SAI_CR2_MSEL_MASK, val_cr2); |
| |
| return 0; |
| } |
| |
| static int fsl_sai_set_mclk_rate(struct snd_soc_dai *dai, int clk_id, unsigned int freq) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(dai); |
| int ret; |
| |
| fsl_asoc_reparent_pll_clocks(dai->dev, sai->mclk_clk[clk_id], |
| sai->pll8k_clk, sai->pll11k_clk, freq); |
| |
| ret = clk_set_rate(sai->mclk_clk[clk_id], freq); |
| if (ret < 0) |
| dev_err(dai->dev, "failed to set clock rate (%u): %d\n", freq, ret); |
| |
| return ret; |
| } |
| |
| static int fsl_sai_set_dai_sysclk(struct snd_soc_dai *cpu_dai, |
| int clk_id, unsigned int freq, int dir) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| int ret; |
| |
| if (dir == SND_SOC_CLOCK_IN) |
| return 0; |
| |
| if (freq > 0 && clk_id != FSL_SAI_CLK_BUS) { |
| if (clk_id < 0 || clk_id >= FSL_SAI_MCLK_MAX) { |
| dev_err(cpu_dai->dev, "Unknown clock id: %d\n", clk_id); |
| return -EINVAL; |
| } |
| |
| if (IS_ERR_OR_NULL(sai->mclk_clk[clk_id])) { |
| dev_err(cpu_dai->dev, "Unassigned clock: %d\n", clk_id); |
| return -EINVAL; |
| } |
| |
| if (sai->mclk_streams == 0) { |
| ret = fsl_sai_set_mclk_rate(cpu_dai, clk_id, freq); |
| if (ret < 0) |
| return ret; |
| } |
| } |
| |
| ret = fsl_sai_set_dai_sysclk_tr(cpu_dai, clk_id, freq, true); |
| if (ret) { |
| dev_err(cpu_dai->dev, "Cannot set tx sysclk: %d\n", ret); |
| return ret; |
| } |
| |
| ret = fsl_sai_set_dai_sysclk_tr(cpu_dai, clk_id, freq, false); |
| if (ret) |
| dev_err(cpu_dai->dev, "Cannot set rx sysclk: %d\n", ret); |
| |
| return ret; |
| } |
| |
| static int fsl_sai_set_dai_fmt_tr(struct snd_soc_dai *cpu_dai, |
| unsigned int fmt, bool tx) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| u32 val_cr2 = 0, val_cr4 = 0; |
| |
| if (!sai->is_lsb_first) |
| val_cr4 |= FSL_SAI_CR4_MF; |
| |
| sai->is_pdm_mode = false; |
| sai->is_dsp_mode = false; |
| /* DAI mode */ |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| /* |
| * Frame low, 1clk before data, one word length for frame sync, |
| * frame sync starts one serial clock cycle earlier, |
| * that is, together with the last bit of the previous |
| * data word. |
| */ |
| val_cr2 |= FSL_SAI_CR2_BCP; |
| val_cr4 |= FSL_SAI_CR4_FSE | FSL_SAI_CR4_FSP; |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| /* |
| * Frame high, one word length for frame sync, |
| * frame sync asserts with the first bit of the frame. |
| */ |
| val_cr2 |= FSL_SAI_CR2_BCP; |
| break; |
| case SND_SOC_DAIFMT_DSP_A: |
| /* |
| * Frame high, 1clk before data, one bit for frame sync, |
| * frame sync starts one serial clock cycle earlier, |
| * that is, together with the last bit of the previous |
| * data word. |
| */ |
| val_cr2 |= FSL_SAI_CR2_BCP; |
| val_cr4 |= FSL_SAI_CR4_FSE; |
| sai->is_dsp_mode = true; |
| break; |
| case SND_SOC_DAIFMT_DSP_B: |
| /* |
| * Frame high, one bit for frame sync, |
| * frame sync asserts with the first bit of the frame. |
| */ |
| val_cr2 |= FSL_SAI_CR2_BCP; |
| sai->is_dsp_mode = true; |
| break; |
| case SND_SOC_DAIFMT_PDM: |
| val_cr2 |= FSL_SAI_CR2_BCP; |
| val_cr4 &= ~FSL_SAI_CR4_MF; |
| sai->is_pdm_mode = true; |
| break; |
| case SND_SOC_DAIFMT_RIGHT_J: |
| /* To be done */ |
| default: |
| return -EINVAL; |
| } |
| |
| /* DAI clock inversion */ |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { |
| case SND_SOC_DAIFMT_IB_IF: |
| /* Invert both clocks */ |
| val_cr2 ^= FSL_SAI_CR2_BCP; |
| val_cr4 ^= FSL_SAI_CR4_FSP; |
| break; |
| case SND_SOC_DAIFMT_IB_NF: |
| /* Invert bit clock */ |
| val_cr2 ^= FSL_SAI_CR2_BCP; |
| break; |
| case SND_SOC_DAIFMT_NB_IF: |
| /* Invert frame clock */ |
| val_cr4 ^= FSL_SAI_CR4_FSP; |
| break; |
| case SND_SOC_DAIFMT_NB_NF: |
| /* Nothing to do for both normal cases */ |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* DAI clock provider masks */ |
| switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { |
| case SND_SOC_DAIFMT_BP_FP: |
| val_cr2 |= FSL_SAI_CR2_BCD_MSTR; |
| val_cr4 |= FSL_SAI_CR4_FSD_MSTR; |
| sai->is_consumer_mode[tx] = false; |
| break; |
| case SND_SOC_DAIFMT_BC_FC: |
| sai->is_consumer_mode[tx] = true; |
| break; |
| case SND_SOC_DAIFMT_BP_FC: |
| val_cr2 |= FSL_SAI_CR2_BCD_MSTR; |
| sai->is_consumer_mode[tx] = false; |
| break; |
| case SND_SOC_DAIFMT_BC_FP: |
| val_cr4 |= FSL_SAI_CR4_FSD_MSTR; |
| sai->is_consumer_mode[tx] = true; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR2(tx, ofs), |
| FSL_SAI_CR2_BCP | FSL_SAI_CR2_BCD_MSTR, val_cr2); |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_MF | FSL_SAI_CR4_FSE | |
| FSL_SAI_CR4_FSP | FSL_SAI_CR4_FSD_MSTR, val_cr4); |
| |
| return 0; |
| } |
| |
| static int fsl_sai_set_dai_fmt(struct snd_soc_dai *cpu_dai, unsigned int fmt) |
| { |
| int ret; |
| |
| ret = fsl_sai_set_dai_fmt_tr(cpu_dai, fmt, true); |
| if (ret) { |
| dev_err(cpu_dai->dev, "Cannot set tx format: %d\n", ret); |
| return ret; |
| } |
| |
| ret = fsl_sai_set_dai_fmt_tr(cpu_dai, fmt, false); |
| if (ret) |
| dev_err(cpu_dai->dev, "Cannot set rx format: %d\n", ret); |
| |
| return ret; |
| } |
| |
| static int fsl_sai_set_dai_fmt_tx(struct snd_soc_dai *cpu_dai, unsigned int fmt) |
| { |
| return fsl_sai_set_dai_fmt_tr(cpu_dai, fmt, true); |
| } |
| |
| static int fsl_sai_set_dai_fmt_rx(struct snd_soc_dai *cpu_dai, unsigned int fmt) |
| { |
| return fsl_sai_set_dai_fmt_tr(cpu_dai, fmt, false); |
| } |
| |
| static int fsl_sai_set_bclk(struct snd_soc_dai *dai, bool tx, u32 freq) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(dai); |
| unsigned int reg, ofs = sai->soc_data->reg_offset; |
| unsigned long clk_rate; |
| u32 savediv = 0, ratio, bestdiff = freq; |
| int adir = tx ? RX : TX; |
| int dir = tx ? TX : RX; |
| u32 id; |
| bool support_1_1_ratio = sai->verid.version >= 0x0301; |
| |
| /* Don't apply to consumer mode */ |
| if (sai->is_consumer_mode[tx]) |
| return 0; |
| |
| /* |
| * There is no point in polling MCLK0 if it is identical to MCLK1. |
| * And given that MQS use case has to use MCLK1 though two clocks |
| * are the same, we simply skip MCLK0 and start to find from MCLK1. |
| */ |
| id = sai->soc_data->mclk0_is_mclk1 ? 1 : 0; |
| |
| for (; id < FSL_SAI_MCLK_MAX; id++) { |
| int diff; |
| |
| clk_rate = clk_get_rate(sai->mclk_clk[id]); |
| if (!clk_rate) |
| continue; |
| |
| ratio = DIV_ROUND_CLOSEST(clk_rate, freq); |
| if (!ratio || ratio > 512) |
| continue; |
| if (ratio == 1 && !support_1_1_ratio) |
| continue; |
| if ((ratio & 1) && ratio > 1) |
| continue; |
| |
| diff = abs((long)clk_rate - ratio * freq); |
| |
| /* |
| * Drop the source that can not be |
| * divided into the required rate. |
| */ |
| if (diff != 0 && clk_rate / diff < 1000) |
| continue; |
| |
| dev_dbg(dai->dev, |
| "ratio %d for freq %dHz based on clock %ldHz\n", |
| ratio, freq, clk_rate); |
| |
| |
| if (diff < bestdiff) { |
| savediv = ratio; |
| sai->mclk_id[tx] = id; |
| bestdiff = diff; |
| } |
| |
| if (diff == 0) |
| break; |
| } |
| |
| if (savediv == 0) { |
| dev_err(dai->dev, "failed to derive required %cx rate: %d\n", |
| tx ? 'T' : 'R', freq); |
| return -EINVAL; |
| } |
| |
| dev_dbg(dai->dev, "best fit: clock id=%d, div=%d, deviation =%d\n", |
| sai->mclk_id[tx], savediv, bestdiff); |
| |
| /* |
| * 1) For Asynchronous mode, we must set RCR2 register for capture, and |
| * set TCR2 register for playback. |
| * 2) For Tx sync with Rx clock, we must set RCR2 register for playback |
| * and capture. |
| * 3) For Rx sync with Tx clock, we must set TCR2 register for playback |
| * and capture. |
| * 4) For Tx and Rx are both Synchronous with another SAI, we just |
| * ignore it. |
| */ |
| if (fsl_sai_dir_is_synced(sai, adir)) |
| reg = FSL_SAI_xCR2(!tx, ofs); |
| else if (!sai->synchronous[dir]) |
| reg = FSL_SAI_xCR2(tx, ofs); |
| else |
| return 0; |
| |
| regmap_update_bits(sai->regmap, reg, FSL_SAI_CR2_MSEL_MASK, |
| FSL_SAI_CR2_MSEL(sai->mclk_id[tx])); |
| |
| if (savediv == 1) { |
| regmap_update_bits(sai->regmap, reg, |
| FSL_SAI_CR2_DIV_MASK | FSL_SAI_CR2_BYP, |
| FSL_SAI_CR2_BYP); |
| if (fsl_sai_dir_is_synced(sai, adir)) |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR2(tx, ofs), |
| FSL_SAI_CR2_BCI, FSL_SAI_CR2_BCI); |
| else |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR2(tx, ofs), |
| FSL_SAI_CR2_BCI, 0); |
| } else { |
| regmap_update_bits(sai->regmap, reg, |
| FSL_SAI_CR2_DIV_MASK | FSL_SAI_CR2_BYP, |
| savediv / 2 - 1); |
| } |
| |
| return 0; |
| } |
| |
| static int fsl_sai_hw_params(struct snd_pcm_substream *substream, |
| struct snd_pcm_hw_params *params, |
| struct snd_soc_dai *cpu_dai) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| unsigned int channels = params_channels(params); |
| struct snd_dmaengine_dai_dma_data *dma_params; |
| struct fsl_sai_dl_cfg *dl_cfg = sai->dl_cfg; |
| u32 word_width = params_width(params); |
| int trce_mask = 0, dl_cfg_idx = 0; |
| int dl_cfg_cnt = sai->dl_cfg_cnt; |
| u32 dl_type = FSL_SAI_DL_I2S; |
| u32 val_cr4 = 0, val_cr5 = 0; |
| u32 slots = (channels == 1) ? 2 : channels; |
| u32 slot_width = word_width; |
| int adir = tx ? RX : TX; |
| u32 pins, bclk; |
| u32 watermark; |
| int ret, i; |
| |
| if (sai->slot_width) |
| slot_width = sai->slot_width; |
| |
| if (sai->slots) |
| slots = sai->slots; |
| else if (sai->bclk_ratio) |
| slots = sai->bclk_ratio / slot_width; |
| |
| pins = DIV_ROUND_UP(channels, slots); |
| |
| /* |
| * PDM mode, channels are independent |
| * each channels are on one dataline/FIFO. |
| */ |
| if (sai->is_pdm_mode) { |
| pins = channels; |
| dl_type = FSL_SAI_DL_PDM; |
| } |
| |
| for (i = 0; i < dl_cfg_cnt; i++) { |
| if (dl_cfg[i].type == dl_type && dl_cfg[i].pins[tx] == pins) { |
| dl_cfg_idx = i; |
| break; |
| } |
| } |
| |
| if (hweight8(dl_cfg[dl_cfg_idx].mask[tx]) < pins) { |
| dev_err(cpu_dai->dev, "channel not supported\n"); |
| return -EINVAL; |
| } |
| |
| bclk = params_rate(params) * (sai->bclk_ratio ? sai->bclk_ratio : slots * slot_width); |
| |
| if (!IS_ERR_OR_NULL(sai->pinctrl)) { |
| sai->pins_state = fsl_sai_get_pins_state(sai, bclk); |
| if (!IS_ERR_OR_NULL(sai->pins_state)) { |
| ret = pinctrl_select_state(sai->pinctrl, sai->pins_state); |
| if (ret) { |
| dev_err(cpu_dai->dev, "failed to set proper pins state: %d\n", ret); |
| return ret; |
| } |
| } |
| } |
| |
| if (!sai->is_consumer_mode[tx]) { |
| ret = fsl_sai_set_bclk(cpu_dai, tx, bclk); |
| if (ret) |
| return ret; |
| |
| /* Do not enable the clock if it is already enabled */ |
| if (!(sai->mclk_streams & BIT(substream->stream))) { |
| ret = clk_prepare_enable(sai->mclk_clk[sai->mclk_id[tx]]); |
| if (ret) |
| return ret; |
| |
| sai->mclk_streams |= BIT(substream->stream); |
| } |
| } |
| |
| if (!sai->is_dsp_mode && !sai->is_pdm_mode) |
| val_cr4 |= FSL_SAI_CR4_SYWD(slot_width); |
| |
| val_cr5 |= FSL_SAI_CR5_WNW(slot_width); |
| val_cr5 |= FSL_SAI_CR5_W0W(slot_width); |
| |
| if (sai->is_lsb_first || sai->is_pdm_mode) |
| val_cr5 |= FSL_SAI_CR5_FBT(0); |
| else |
| val_cr5 |= FSL_SAI_CR5_FBT(word_width - 1); |
| |
| val_cr4 |= FSL_SAI_CR4_FRSZ(slots); |
| |
| /* Set to avoid channel swap */ |
| val_cr4 |= FSL_SAI_CR4_FCONT; |
| |
| /* Set to output mode to avoid tri-stated data pins */ |
| if (tx) |
| val_cr4 |= FSL_SAI_CR4_CHMOD; |
| |
| /* |
| * For SAI provider mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will |
| * generate bclk and frame clock for Tx(Rx), we should set RCR4(TCR4), |
| * RCR5(TCR5) for playback(capture), or there will be sync error. |
| */ |
| |
| if (!sai->is_consumer_mode[tx] && fsl_sai_dir_is_synced(sai, adir)) { |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(!tx, ofs), |
| FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK | |
| FSL_SAI_CR4_CHMOD_MASK, |
| val_cr4); |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR5(!tx, ofs), |
| FSL_SAI_CR5_WNW_MASK | FSL_SAI_CR5_W0W_MASK | |
| FSL_SAI_CR5_FBT_MASK, val_cr5); |
| } |
| |
| /* |
| * Combine mode has limation: |
| * - Can't used for singel dataline/FIFO case except the FIFO0 |
| * - Can't used for multi dataline/FIFO case except the enabled FIFOs |
| * are successive and start from FIFO0 |
| * |
| * So for common usage, all multi fifo case disable the combine mode. |
| */ |
| if (hweight8(dl_cfg[dl_cfg_idx].mask[tx]) <= 1 || sai->is_multi_fifo_dma) |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_FCOMB_MASK, 0); |
| else |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_FCOMB_MASK, FSL_SAI_CR4_FCOMB_SOFT); |
| |
| dma_params = tx ? &sai->dma_params_tx : &sai->dma_params_rx; |
| dma_params->addr = sai->res->start + FSL_SAI_xDR0(tx) + |
| dl_cfg[dl_cfg_idx].start_off[tx] * 0x4; |
| |
| if (sai->is_multi_fifo_dma) { |
| sai->audio_config[tx].words_per_fifo = min(slots, channels); |
| if (tx) { |
| sai->audio_config[tx].n_fifos_dst = pins; |
| sai->audio_config[tx].stride_fifos_dst = dl_cfg[dl_cfg_idx].next_off[tx]; |
| } else { |
| sai->audio_config[tx].n_fifos_src = pins; |
| sai->audio_config[tx].stride_fifos_src = dl_cfg[dl_cfg_idx].next_off[tx]; |
| } |
| dma_params->maxburst = sai->audio_config[tx].words_per_fifo * pins; |
| dma_params->peripheral_config = &sai->audio_config[tx]; |
| dma_params->peripheral_size = sizeof(sai->audio_config[tx]); |
| |
| watermark = tx ? (sai->soc_data->fifo_depth - dma_params->maxburst) : |
| (dma_params->maxburst - 1); |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR1(tx, ofs), |
| FSL_SAI_CR1_RFW_MASK(sai->soc_data->fifo_depth), |
| watermark); |
| } |
| |
| /* Find a proper tcre setting */ |
| for (i = 0; i < sai->soc_data->pins; i++) { |
| trce_mask = (1 << (i + 1)) - 1; |
| if (hweight8(dl_cfg[dl_cfg_idx].mask[tx] & trce_mask) == pins) |
| break; |
| } |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR3(tx, ofs), |
| FSL_SAI_CR3_TRCE_MASK, |
| FSL_SAI_CR3_TRCE((dl_cfg[dl_cfg_idx].mask[tx] & trce_mask))); |
| |
| /* |
| * When the TERE and FSD_MSTR enabled before configuring the word width |
| * There will be no frame sync clock issue, because word width impact |
| * the generation of frame sync clock. |
| * |
| * TERE enabled earlier only for i.MX8MP case for the hardware limitation, |
| * We need to disable FSD_MSTR before configuring word width, then enable |
| * FSD_MSTR bit for this specific case. |
| */ |
| if (sai->soc_data->mclk_with_tere && sai->mclk_direction_output && |
| !sai->is_consumer_mode[tx]) |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_FSD_MSTR, 0); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK | |
| FSL_SAI_CR4_CHMOD_MASK | FSL_SAI_CR4_FCONT_MASK, |
| val_cr4); |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR5(tx, ofs), |
| FSL_SAI_CR5_WNW_MASK | FSL_SAI_CR5_W0W_MASK | |
| FSL_SAI_CR5_FBT_MASK, val_cr5); |
| |
| /* Enable FSD_MSTR after configuring word width */ |
| if (sai->soc_data->mclk_with_tere && sai->mclk_direction_output && |
| !sai->is_consumer_mode[tx]) |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), |
| FSL_SAI_CR4_FSD_MSTR, FSL_SAI_CR4_FSD_MSTR); |
| |
| regmap_write(sai->regmap, FSL_SAI_xMR(tx), |
| ~0UL - ((1 << min(channels, slots)) - 1)); |
| |
| return 0; |
| } |
| |
| static int fsl_sai_hw_free(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *cpu_dai) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| /* Clear xMR to avoid channel swap with mclk_with_tere enabled case */ |
| regmap_write(sai->regmap, FSL_SAI_xMR(tx), 0); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCR3(tx, ofs), |
| FSL_SAI_CR3_TRCE_MASK, 0); |
| |
| if (!sai->is_consumer_mode[tx] && |
| sai->mclk_streams & BIT(substream->stream)) { |
| clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[tx]]); |
| sai->mclk_streams &= ~BIT(substream->stream); |
| } |
| |
| return 0; |
| } |
| |
| static void fsl_sai_config_disable(struct fsl_sai *sai, int dir) |
| { |
| unsigned int ofs = sai->soc_data->reg_offset; |
| bool tx = dir == TX; |
| u32 xcsr, count = 100, mask; |
| |
| if (sai->soc_data->mclk_with_tere && sai->mclk_direction_output) |
| mask = FSL_SAI_CSR_TERE; |
| else |
| mask = FSL_SAI_CSR_TERE | FSL_SAI_CSR_BCE; |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| mask, 0); |
| |
| /* TERE will remain set till the end of current frame */ |
| do { |
| udelay(10); |
| regmap_read(sai->regmap, FSL_SAI_xCSR(tx, ofs), &xcsr); |
| } while (--count && xcsr & FSL_SAI_CSR_TERE); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_FR, FSL_SAI_CSR_FR); |
| |
| /* |
| * For sai master mode, after several open/close sai, |
| * there will be no frame clock, and can't recover |
| * anymore. Add software reset to fix this issue. |
| * This is a hardware bug, and will be fix in the |
| * next sai version. |
| */ |
| if (!sai->is_consumer_mode[tx]) { |
| /* Software Reset */ |
| regmap_write(sai->regmap, FSL_SAI_xCSR(tx, ofs), FSL_SAI_CSR_SR); |
| /* Clear SR bit to finish the reset */ |
| regmap_write(sai->regmap, FSL_SAI_xCSR(tx, ofs), 0); |
| } |
| } |
| |
| static int fsl_sai_trigger(struct snd_pcm_substream *substream, int cmd, |
| struct snd_soc_dai *cpu_dai) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| int adir = tx ? RX : TX; |
| int dir = tx ? TX : RX; |
| u32 xcsr; |
| |
| /* |
| * Asynchronous mode: Clear SYNC for both Tx and Rx. |
| * Rx sync with Tx clocks: Clear SYNC for Tx, set it for Rx. |
| * Tx sync with Rx clocks: Clear SYNC for Rx, set it for Tx. |
| */ |
| regmap_update_bits(sai->regmap, FSL_SAI_TCR2(ofs), FSL_SAI_CR2_SYNC, |
| sai->synchronous[TX] ? FSL_SAI_CR2_SYNC : 0); |
| regmap_update_bits(sai->regmap, FSL_SAI_RCR2(ofs), FSL_SAI_CR2_SYNC, |
| sai->synchronous[RX] ? FSL_SAI_CR2_SYNC : 0); |
| |
| /* |
| * It is recommended that the transmitter is the last enabled |
| * and the first disabled. |
| */ |
| switch (cmd) { |
| case SNDRV_PCM_TRIGGER_START: |
| case SNDRV_PCM_TRIGGER_RESUME: |
| case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_FRDE, FSL_SAI_CSR_FRDE); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_TERE, FSL_SAI_CSR_TERE); |
| /* |
| * Enable the opposite direction for synchronous mode |
| * 1. Tx sync with Rx: only set RE for Rx; set TE & RE for Tx |
| * 2. Rx sync with Tx: only set TE for Tx; set RE & TE for Rx |
| * |
| * RM recommends to enable RE after TE for case 1 and to enable |
| * TE after RE for case 2, but we here may not always guarantee |
| * that happens: "arecord 1.wav; aplay 2.wav" in case 1 enables |
| * TE after RE, which is against what RM recommends but should |
| * be safe to do, judging by years of testing results. |
| */ |
| if (fsl_sai_dir_is_synced(sai, adir)) |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR((!tx), ofs), |
| FSL_SAI_CSR_TERE, FSL_SAI_CSR_TERE); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_xIE_MASK, FSL_SAI_FLAGS); |
| break; |
| case SNDRV_PCM_TRIGGER_STOP: |
| case SNDRV_PCM_TRIGGER_SUSPEND: |
| case SNDRV_PCM_TRIGGER_PAUSE_PUSH: |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_FRDE, 0); |
| regmap_update_bits(sai->regmap, FSL_SAI_xCSR(tx, ofs), |
| FSL_SAI_CSR_xIE_MASK, 0); |
| |
| /* Check if the opposite FRDE is also disabled */ |
| regmap_read(sai->regmap, FSL_SAI_xCSR(!tx, ofs), &xcsr); |
| |
| /* |
| * If opposite stream provides clocks for synchronous mode and |
| * it is inactive, disable it before disabling the current one |
| */ |
| if (fsl_sai_dir_is_synced(sai, adir) && !(xcsr & FSL_SAI_CSR_FRDE)) |
| fsl_sai_config_disable(sai, adir); |
| |
| /* |
| * Disable current stream if either of: |
| * 1. current stream doesn't provide clocks for synchronous mode |
| * 2. current stream provides clocks for synchronous mode but no |
| * more stream is active. |
| */ |
| if (!fsl_sai_dir_is_synced(sai, dir) || !(xcsr & FSL_SAI_CSR_FRDE)) |
| fsl_sai_config_disable(sai, dir); |
| |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int fsl_sai_startup(struct snd_pcm_substream *substream, |
| struct snd_soc_dai *cpu_dai) |
| { |
| struct fsl_sai *sai = snd_soc_dai_get_drvdata(cpu_dai); |
| bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; |
| int ret; |
| |
| /* |
| * EDMA controller needs period size to be a multiple of |
| * tx/rx maxburst |
| */ |
| if (sai->soc_data->use_edma) |
| snd_pcm_hw_constraint_step(substream->runtime, 0, |
| SNDRV_PCM_HW_PARAM_PERIOD_SIZE, |
| tx ? sai->dma_params_tx.maxburst : |
| sai->dma_params_rx.maxburst); |
| |
| ret = snd_pcm_hw_constraint_list(substream->runtime, 0, |
| SNDRV_PCM_HW_PARAM_RATE, &fsl_sai_rate_constraints); |
| |
| return ret; |
| } |
| |
| static int fsl_sai_dai_probe(struct snd_soc_dai *cpu_dai) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(cpu_dai->dev); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| /* Software Reset for both Tx and Rx */ |
| regmap_write(sai->regmap, FSL_SAI_TCSR(ofs), FSL_SAI_CSR_SR); |
| regmap_write(sai->regmap, FSL_SAI_RCSR(ofs), FSL_SAI_CSR_SR); |
| /* Clear SR bit to finish the reset */ |
| regmap_write(sai->regmap, FSL_SAI_TCSR(ofs), 0); |
| regmap_write(sai->regmap, FSL_SAI_RCSR(ofs), 0); |
| |
| regmap_update_bits(sai->regmap, FSL_SAI_TCR1(ofs), |
| FSL_SAI_CR1_RFW_MASK(sai->soc_data->fifo_depth), |
| sai->soc_data->fifo_depth - sai->dma_params_tx.maxburst); |
| regmap_update_bits(sai->regmap, FSL_SAI_RCR1(ofs), |
| FSL_SAI_CR1_RFW_MASK(sai->soc_data->fifo_depth), |
| sai->dma_params_rx.maxburst - 1); |
| |
| snd_soc_dai_init_dma_data(cpu_dai, &sai->dma_params_tx, |
| &sai->dma_params_rx); |
| |
| return 0; |
| } |
| |
| static const struct snd_soc_dai_ops fsl_sai_pcm_dai_ops = { |
| .probe = fsl_sai_dai_probe, |
| .set_bclk_ratio = fsl_sai_set_dai_bclk_ratio, |
| .set_sysclk = fsl_sai_set_dai_sysclk, |
| .set_fmt = fsl_sai_set_dai_fmt, |
| .set_tdm_slot = fsl_sai_set_dai_tdm_slot, |
| .hw_params = fsl_sai_hw_params, |
| .hw_free = fsl_sai_hw_free, |
| .trigger = fsl_sai_trigger, |
| .startup = fsl_sai_startup, |
| }; |
| |
| static const struct snd_soc_dai_ops fsl_sai_pcm_dai_tx_ops = { |
| .probe = fsl_sai_dai_probe, |
| .set_bclk_ratio = fsl_sai_set_dai_bclk_ratio, |
| .set_sysclk = fsl_sai_set_dai_sysclk, |
| .set_fmt = fsl_sai_set_dai_fmt_tx, |
| .set_tdm_slot = fsl_sai_set_dai_tdm_slot, |
| .hw_params = fsl_sai_hw_params, |
| .hw_free = fsl_sai_hw_free, |
| .trigger = fsl_sai_trigger, |
| .startup = fsl_sai_startup, |
| }; |
| |
| static const struct snd_soc_dai_ops fsl_sai_pcm_dai_rx_ops = { |
| .probe = fsl_sai_dai_probe, |
| .set_bclk_ratio = fsl_sai_set_dai_bclk_ratio, |
| .set_sysclk = fsl_sai_set_dai_sysclk, |
| .set_fmt = fsl_sai_set_dai_fmt_rx, |
| .set_tdm_slot = fsl_sai_set_dai_tdm_slot, |
| .hw_params = fsl_sai_hw_params, |
| .hw_free = fsl_sai_hw_free, |
| .trigger = fsl_sai_trigger, |
| .startup = fsl_sai_startup, |
| }; |
| |
| static int fsl_sai_dai_resume(struct snd_soc_component *component) |
| { |
| struct fsl_sai *sai = snd_soc_component_get_drvdata(component); |
| struct device *dev = &sai->pdev->dev; |
| int ret; |
| |
| if (!IS_ERR_OR_NULL(sai->pinctrl) && !IS_ERR_OR_NULL(sai->pins_state)) { |
| ret = pinctrl_select_state(sai->pinctrl, sai->pins_state); |
| if (ret) { |
| dev_err(dev, "failed to set proper pins state: %d\n", ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static struct snd_soc_dai_driver fsl_sai_dai_template[] = { |
| { |
| .name = "sai-tx-rx", |
| .playback = { |
| .stream_name = "CPU-Playback", |
| .channels_min = 1, |
| .channels_max = 32, |
| .rate_min = 8000, |
| .rate_max = 2822400, |
| .rates = SNDRV_PCM_RATE_KNOT, |
| .formats = FSL_SAI_FORMATS, |
| }, |
| .capture = { |
| .stream_name = "CPU-Capture", |
| .channels_min = 1, |
| .channels_max = 32, |
| .rate_min = 8000, |
| .rate_max = 2822400, |
| .rates = SNDRV_PCM_RATE_KNOT, |
| .formats = FSL_SAI_FORMATS, |
| }, |
| .ops = &fsl_sai_pcm_dai_ops, |
| }, |
| { |
| .name = "sai-tx", |
| .playback = { |
| .stream_name = "CPU-Playback", |
| .channels_min = 1, |
| .channels_max = 32, |
| .rate_min = 8000, |
| .rate_max = 2822400, |
| .rates = SNDRV_PCM_RATE_KNOT, |
| .formats = FSL_SAI_FORMATS, |
| }, |
| .ops = &fsl_sai_pcm_dai_tx_ops, |
| }, |
| { |
| .name = "sai-rx", |
| .capture = { |
| .stream_name = "CPU-Capture", |
| .channels_min = 1, |
| .channels_max = 32, |
| .rate_min = 8000, |
| .rate_max = 2822400, |
| .rates = SNDRV_PCM_RATE_KNOT, |
| .formats = FSL_SAI_FORMATS, |
| }, |
| .ops = &fsl_sai_pcm_dai_rx_ops, |
| }, |
| }; |
| |
| static const struct snd_soc_component_driver fsl_component = { |
| .name = "fsl-sai", |
| .resume = fsl_sai_dai_resume, |
| .legacy_dai_naming = 1, |
| }; |
| |
| static struct reg_default fsl_sai_reg_defaults_ofs0[] = { |
| {FSL_SAI_TCR1(0), 0}, |
| {FSL_SAI_TCR2(0), 0}, |
| {FSL_SAI_TCR3(0), 0}, |
| {FSL_SAI_TCR4(0), 0}, |
| {FSL_SAI_TCR5(0), 0}, |
| {FSL_SAI_TDR0, 0}, |
| {FSL_SAI_TDR1, 0}, |
| {FSL_SAI_TDR2, 0}, |
| {FSL_SAI_TDR3, 0}, |
| {FSL_SAI_TDR4, 0}, |
| {FSL_SAI_TDR5, 0}, |
| {FSL_SAI_TDR6, 0}, |
| {FSL_SAI_TDR7, 0}, |
| {FSL_SAI_TMR, 0}, |
| {FSL_SAI_RCR1(0), 0}, |
| {FSL_SAI_RCR2(0), 0}, |
| {FSL_SAI_RCR3(0), 0}, |
| {FSL_SAI_RCR4(0), 0}, |
| {FSL_SAI_RCR5(0), 0}, |
| {FSL_SAI_RMR, 0}, |
| }; |
| |
| static struct reg_default fsl_sai_reg_defaults_ofs8[] = { |
| {FSL_SAI_TCR1(8), 0}, |
| {FSL_SAI_TCR2(8), 0}, |
| {FSL_SAI_TCR3(8), 0}, |
| {FSL_SAI_TCR4(8), 0}, |
| {FSL_SAI_TCR5(8), 0}, |
| {FSL_SAI_TDR0, 0}, |
| {FSL_SAI_TDR1, 0}, |
| {FSL_SAI_TDR2, 0}, |
| {FSL_SAI_TDR3, 0}, |
| {FSL_SAI_TDR4, 0}, |
| {FSL_SAI_TDR5, 0}, |
| {FSL_SAI_TDR6, 0}, |
| {FSL_SAI_TDR7, 0}, |
| {FSL_SAI_TMR, 0}, |
| {FSL_SAI_RCR1(8), 0}, |
| {FSL_SAI_RCR2(8), 0}, |
| {FSL_SAI_RCR3(8), 0}, |
| {FSL_SAI_RCR4(8), 0}, |
| {FSL_SAI_RCR5(8), 0}, |
| {FSL_SAI_RMR, 0}, |
| {FSL_SAI_MCTL, 0}, |
| {FSL_SAI_MDIV, 0}, |
| }; |
| |
| static bool fsl_sai_readable_reg(struct device *dev, unsigned int reg) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| if (reg >= FSL_SAI_TCSR(ofs) && reg <= FSL_SAI_TCR5(ofs)) |
| return true; |
| |
| if (reg >= FSL_SAI_RCSR(ofs) && reg <= FSL_SAI_RCR5(ofs)) |
| return true; |
| |
| switch (reg) { |
| case FSL_SAI_TFR0: |
| case FSL_SAI_TFR1: |
| case FSL_SAI_TFR2: |
| case FSL_SAI_TFR3: |
| case FSL_SAI_TFR4: |
| case FSL_SAI_TFR5: |
| case FSL_SAI_TFR6: |
| case FSL_SAI_TFR7: |
| case FSL_SAI_TMR: |
| case FSL_SAI_RDR0: |
| case FSL_SAI_RDR1: |
| case FSL_SAI_RDR2: |
| case FSL_SAI_RDR3: |
| case FSL_SAI_RDR4: |
| case FSL_SAI_RDR5: |
| case FSL_SAI_RDR6: |
| case FSL_SAI_RDR7: |
| case FSL_SAI_RFR0: |
| case FSL_SAI_RFR1: |
| case FSL_SAI_RFR2: |
| case FSL_SAI_RFR3: |
| case FSL_SAI_RFR4: |
| case FSL_SAI_RFR5: |
| case FSL_SAI_RFR6: |
| case FSL_SAI_RFR7: |
| case FSL_SAI_RMR: |
| case FSL_SAI_MCTL: |
| case FSL_SAI_MDIV: |
| case FSL_SAI_VERID: |
| case FSL_SAI_PARAM: |
| case FSL_SAI_TTCTN: |
| case FSL_SAI_RTCTN: |
| case FSL_SAI_TTCTL: |
| case FSL_SAI_TBCTN: |
| case FSL_SAI_TTCAP: |
| case FSL_SAI_RTCTL: |
| case FSL_SAI_RBCTN: |
| case FSL_SAI_RTCAP: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool fsl_sai_volatile_reg(struct device *dev, unsigned int reg) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| if (reg == FSL_SAI_TCSR(ofs) || reg == FSL_SAI_RCSR(ofs)) |
| return true; |
| |
| /* Set VERID and PARAM be volatile for reading value in probe */ |
| if (ofs == 8 && (reg == FSL_SAI_VERID || reg == FSL_SAI_PARAM)) |
| return true; |
| |
| switch (reg) { |
| case FSL_SAI_TFR0: |
| case FSL_SAI_TFR1: |
| case FSL_SAI_TFR2: |
| case FSL_SAI_TFR3: |
| case FSL_SAI_TFR4: |
| case FSL_SAI_TFR5: |
| case FSL_SAI_TFR6: |
| case FSL_SAI_TFR7: |
| case FSL_SAI_RFR0: |
| case FSL_SAI_RFR1: |
| case FSL_SAI_RFR2: |
| case FSL_SAI_RFR3: |
| case FSL_SAI_RFR4: |
| case FSL_SAI_RFR5: |
| case FSL_SAI_RFR6: |
| case FSL_SAI_RFR7: |
| case FSL_SAI_RDR0: |
| case FSL_SAI_RDR1: |
| case FSL_SAI_RDR2: |
| case FSL_SAI_RDR3: |
| case FSL_SAI_RDR4: |
| case FSL_SAI_RDR5: |
| case FSL_SAI_RDR6: |
| case FSL_SAI_RDR7: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool fsl_sai_writeable_reg(struct device *dev, unsigned int reg) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| |
| if (reg >= FSL_SAI_TCSR(ofs) && reg <= FSL_SAI_TCR5(ofs)) |
| return true; |
| |
| if (reg >= FSL_SAI_RCSR(ofs) && reg <= FSL_SAI_RCR5(ofs)) |
| return true; |
| |
| switch (reg) { |
| case FSL_SAI_TDR0: |
| case FSL_SAI_TDR1: |
| case FSL_SAI_TDR2: |
| case FSL_SAI_TDR3: |
| case FSL_SAI_TDR4: |
| case FSL_SAI_TDR5: |
| case FSL_SAI_TDR6: |
| case FSL_SAI_TDR7: |
| case FSL_SAI_TMR: |
| case FSL_SAI_RMR: |
| case FSL_SAI_MCTL: |
| case FSL_SAI_MDIV: |
| case FSL_SAI_TTCTL: |
| case FSL_SAI_RTCTL: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static struct regmap_config fsl_sai_regmap_config = { |
| .reg_bits = 32, |
| .reg_stride = 4, |
| .val_bits = 32, |
| .fast_io = true, |
| |
| .max_register = FSL_SAI_RMR, |
| .reg_defaults = fsl_sai_reg_defaults_ofs0, |
| .num_reg_defaults = ARRAY_SIZE(fsl_sai_reg_defaults_ofs0), |
| .readable_reg = fsl_sai_readable_reg, |
| .volatile_reg = fsl_sai_volatile_reg, |
| .writeable_reg = fsl_sai_writeable_reg, |
| .cache_type = REGCACHE_FLAT, |
| }; |
| |
| static int fsl_sai_check_version(struct device *dev) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| unsigned char ofs = sai->soc_data->reg_offset; |
| unsigned int val; |
| int ret; |
| |
| if (FSL_SAI_TCSR(ofs) == FSL_SAI_VERID) |
| return 0; |
| |
| ret = regmap_read(sai->regmap, FSL_SAI_VERID, &val); |
| if (ret < 0) |
| return ret; |
| |
| dev_dbg(dev, "VERID: 0x%016X\n", val); |
| |
| sai->verid.version = val & |
| (FSL_SAI_VERID_MAJOR_MASK | FSL_SAI_VERID_MINOR_MASK); |
| sai->verid.version >>= FSL_SAI_VERID_MINOR_SHIFT; |
| sai->verid.feature = val & FSL_SAI_VERID_FEATURE_MASK; |
| |
| ret = regmap_read(sai->regmap, FSL_SAI_PARAM, &val); |
| if (ret < 0) |
| return ret; |
| |
| dev_dbg(dev, "PARAM: 0x%016X\n", val); |
| |
| /* Max slots per frame, power of 2 */ |
| sai->param.slot_num = 1 << |
| ((val & FSL_SAI_PARAM_SPF_MASK) >> FSL_SAI_PARAM_SPF_SHIFT); |
| |
| /* Words per fifo, power of 2 */ |
| sai->param.fifo_depth = 1 << |
| ((val & FSL_SAI_PARAM_WPF_MASK) >> FSL_SAI_PARAM_WPF_SHIFT); |
| |
| /* Number of datalines implemented */ |
| sai->param.dataline = val & FSL_SAI_PARAM_DLN_MASK; |
| |
| return 0; |
| } |
| |
| /* |
| * Calculate the offset between first two datalines, don't |
| * different offset in one case. |
| */ |
| static unsigned int fsl_sai_calc_dl_off(unsigned long dl_mask) |
| { |
| int fbidx, nbidx, offset; |
| |
| fbidx = find_first_bit(&dl_mask, FSL_SAI_DL_NUM); |
| nbidx = find_next_bit(&dl_mask, FSL_SAI_DL_NUM, fbidx + 1); |
| offset = nbidx - fbidx - 1; |
| |
| return (offset < 0 || offset >= (FSL_SAI_DL_NUM - 1) ? 0 : offset); |
| } |
| |
| /* |
| * read the fsl,dataline property from dts file. |
| * It has 3 value for each configuration, first one means the type: |
| * I2S(1) or PDM(2), second one is dataline mask for 'rx', third one is |
| * dataline mask for 'tx'. for example |
| * |
| * fsl,dataline = <1 0xff 0xff 2 0xff 0x11>, |
| * |
| * It means I2S type rx mask is 0xff, tx mask is 0xff, PDM type |
| * rx mask is 0xff, tx mask is 0x11 (dataline 1 and 4 enabled). |
| * |
| */ |
| static int fsl_sai_read_dlcfg(struct fsl_sai *sai) |
| { |
| struct platform_device *pdev = sai->pdev; |
| struct device_node *np = pdev->dev.of_node; |
| struct device *dev = &pdev->dev; |
| int ret, elems, i, index, num_cfg; |
| char *propname = "fsl,dataline"; |
| struct fsl_sai_dl_cfg *cfg; |
| unsigned long dl_mask; |
| unsigned int soc_dl; |
| u32 rx, tx, type; |
| |
| elems = of_property_count_u32_elems(np, propname); |
| |
| if (elems <= 0) { |
| elems = 0; |
| } else if (elems % 3) { |
| dev_err(dev, "Number of elements must be divisible to 3.\n"); |
| return -EINVAL; |
| } |
| |
| num_cfg = elems / 3; |
| /* Add one more for default value */ |
| cfg = devm_kzalloc(&pdev->dev, (num_cfg + 1) * sizeof(*cfg), GFP_KERNEL); |
| if (!cfg) |
| return -ENOMEM; |
| |
| /* Consider default value "0 0xFF 0xFF" if property is missing */ |
| soc_dl = BIT(sai->soc_data->pins) - 1; |
| cfg[0].type = FSL_SAI_DL_DEFAULT; |
| cfg[0].pins[0] = sai->soc_data->pins; |
| cfg[0].mask[0] = soc_dl; |
| cfg[0].start_off[0] = 0; |
| cfg[0].next_off[0] = 0; |
| |
| cfg[0].pins[1] = sai->soc_data->pins; |
| cfg[0].mask[1] = soc_dl; |
| cfg[0].start_off[1] = 0; |
| cfg[0].next_off[1] = 0; |
| for (i = 1, index = 0; i < num_cfg + 1; i++) { |
| /* |
| * type of dataline |
| * 0 means default mode |
| * 1 means I2S mode |
| * 2 means PDM mode |
| */ |
| ret = of_property_read_u32_index(np, propname, index++, &type); |
| if (ret) |
| return -EINVAL; |
| |
| ret = of_property_read_u32_index(np, propname, index++, &rx); |
| if (ret) |
| return -EINVAL; |
| |
| ret = of_property_read_u32_index(np, propname, index++, &tx); |
| if (ret) |
| return -EINVAL; |
| |
| if ((rx & ~soc_dl) || (tx & ~soc_dl)) { |
| dev_err(dev, "dataline cfg[%d] setting error, mask is 0x%x\n", i, soc_dl); |
| return -EINVAL; |
| } |
| |
| rx = rx & soc_dl; |
| tx = tx & soc_dl; |
| |
| cfg[i].type = type; |
| cfg[i].pins[0] = hweight8(rx); |
| cfg[i].mask[0] = rx; |
| dl_mask = rx; |
| cfg[i].start_off[0] = find_first_bit(&dl_mask, FSL_SAI_DL_NUM); |
| cfg[i].next_off[0] = fsl_sai_calc_dl_off(rx); |
| |
| cfg[i].pins[1] = hweight8(tx); |
| cfg[i].mask[1] = tx; |
| dl_mask = tx; |
| cfg[i].start_off[1] = find_first_bit(&dl_mask, FSL_SAI_DL_NUM); |
| cfg[i].next_off[1] = fsl_sai_calc_dl_off(tx); |
| } |
| |
| sai->dl_cfg = cfg; |
| sai->dl_cfg_cnt = num_cfg + 1; |
| return 0; |
| } |
| |
| static int fsl_sai_runtime_suspend(struct device *dev); |
| static int fsl_sai_runtime_resume(struct device *dev); |
| |
| static int fsl_sai_probe(struct platform_device *pdev) |
| { |
| struct device_node *np = pdev->dev.of_node; |
| struct device *dev = &pdev->dev; |
| struct fsl_sai *sai; |
| struct regmap *gpr; |
| void __iomem *base; |
| char tmp[8]; |
| int irq, ret, i; |
| int index; |
| u32 dmas[4]; |
| |
| sai = devm_kzalloc(dev, sizeof(*sai), GFP_KERNEL); |
| if (!sai) |
| return -ENOMEM; |
| |
| sai->pdev = pdev; |
| sai->soc_data = of_device_get_match_data(dev); |
| |
| sai->is_lsb_first = of_property_read_bool(np, "lsb-first"); |
| |
| base = devm_platform_get_and_ioremap_resource(pdev, 0, &sai->res); |
| if (IS_ERR(base)) |
| return PTR_ERR(base); |
| |
| if (sai->soc_data->reg_offset == 8) { |
| fsl_sai_regmap_config.reg_defaults = fsl_sai_reg_defaults_ofs8; |
| fsl_sai_regmap_config.max_register = FSL_SAI_MDIV; |
| fsl_sai_regmap_config.num_reg_defaults = |
| ARRAY_SIZE(fsl_sai_reg_defaults_ofs8); |
| } |
| |
| sai->regmap = devm_regmap_init_mmio(dev, base, &fsl_sai_regmap_config); |
| if (IS_ERR(sai->regmap)) { |
| dev_err(dev, "regmap init failed\n"); |
| return PTR_ERR(sai->regmap); |
| } |
| |
| sai->bus_clk = devm_clk_get(dev, "bus"); |
| /* Compatible with old DTB cases */ |
| if (IS_ERR(sai->bus_clk) && PTR_ERR(sai->bus_clk) != -EPROBE_DEFER) |
| sai->bus_clk = devm_clk_get(dev, "sai"); |
| if (IS_ERR(sai->bus_clk)) { |
| dev_err(dev, "failed to get bus clock: %ld\n", |
| PTR_ERR(sai->bus_clk)); |
| /* -EPROBE_DEFER */ |
| return PTR_ERR(sai->bus_clk); |
| } |
| |
| for (i = 1; i < FSL_SAI_MCLK_MAX; i++) { |
| sprintf(tmp, "mclk%d", i); |
| sai->mclk_clk[i] = devm_clk_get(dev, tmp); |
| if (IS_ERR(sai->mclk_clk[i])) { |
| dev_err(dev, "failed to get mclk%d clock: %ld\n", |
| i, PTR_ERR(sai->mclk_clk[i])); |
| sai->mclk_clk[i] = NULL; |
| } |
| } |
| |
| if (sai->soc_data->mclk0_is_mclk1) |
| sai->mclk_clk[0] = sai->mclk_clk[1]; |
| else |
| sai->mclk_clk[0] = sai->bus_clk; |
| |
| fsl_asoc_get_pll_clocks(&pdev->dev, &sai->pll8k_clk, |
| &sai->pll11k_clk); |
| |
| /* Use Multi FIFO mode depending on the support from SDMA script */ |
| ret = of_property_read_u32_array(np, "dmas", dmas, 4); |
| if (!sai->soc_data->use_edma && !ret && dmas[2] == IMX_DMATYPE_MULTI_SAI) |
| sai->is_multi_fifo_dma = true; |
| |
| /* read dataline mask for rx and tx*/ |
| ret = fsl_sai_read_dlcfg(sai); |
| if (ret < 0) { |
| dev_err(dev, "failed to read dlcfg %d\n", ret); |
| return ret; |
| } |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| ret = devm_request_irq(dev, irq, fsl_sai_isr, IRQF_SHARED, |
| np->name, sai); |
| if (ret) { |
| dev_err(dev, "failed to claim irq %u\n", irq); |
| return ret; |
| } |
| |
| memcpy(&sai->cpu_dai_drv, fsl_sai_dai_template, |
| sizeof(*fsl_sai_dai_template) * ARRAY_SIZE(fsl_sai_dai_template)); |
| |
| /* Sync Tx with Rx as default by following old DT binding */ |
| sai->synchronous[RX] = true; |
| sai->synchronous[TX] = false; |
| sai->cpu_dai_drv[0].symmetric_rate = 1; |
| sai->cpu_dai_drv[0].symmetric_channels = 1; |
| sai->cpu_dai_drv[0].symmetric_sample_bits = 1; |
| |
| if (of_property_read_bool(np, "fsl,sai-synchronous-rx") && |
| of_property_read_bool(np, "fsl,sai-asynchronous")) { |
| /* error out if both synchronous and asynchronous are present */ |
| dev_err(dev, "invalid binding for synchronous mode\n"); |
| return -EINVAL; |
| } |
| |
| if (of_property_read_bool(np, "fsl,sai-synchronous-rx")) { |
| /* Sync Rx with Tx */ |
| sai->synchronous[RX] = false; |
| sai->synchronous[TX] = true; |
| } else if (of_property_read_bool(np, "fsl,sai-asynchronous")) { |
| /* Discard all settings for asynchronous mode */ |
| sai->synchronous[RX] = false; |
| sai->synchronous[TX] = false; |
| sai->cpu_dai_drv[0].symmetric_rate = 0; |
| sai->cpu_dai_drv[0].symmetric_channels = 0; |
| sai->cpu_dai_drv[0].symmetric_sample_bits = 0; |
| } |
| |
| sai->mclk_direction_output = of_property_read_bool(np, "fsl,sai-mclk-direction-output"); |
| |
| if (sai->mclk_direction_output && |
| of_device_is_compatible(np, "fsl,imx6ul-sai")) { |
| gpr = syscon_regmap_lookup_by_compatible("fsl,imx6ul-iomuxc-gpr"); |
| if (IS_ERR(gpr)) { |
| dev_err(dev, "cannot find iomuxc registers\n"); |
| return PTR_ERR(gpr); |
| } |
| |
| index = of_alias_get_id(np, "sai"); |
| if (index < 0) |
| return index; |
| |
| regmap_update_bits(gpr, IOMUXC_GPR1, MCLK_DIR(index), |
| MCLK_DIR(index)); |
| } |
| |
| sai->dma_params_rx.addr = sai->res->start + FSL_SAI_RDR0; |
| sai->dma_params_tx.addr = sai->res->start + FSL_SAI_TDR0; |
| sai->dma_params_rx.maxburst = |
| sai->soc_data->max_burst[RX] ? sai->soc_data->max_burst[RX] : FSL_SAI_MAXBURST_RX; |
| sai->dma_params_tx.maxburst = |
| sai->soc_data->max_burst[TX] ? sai->soc_data->max_burst[TX] : FSL_SAI_MAXBURST_TX; |
| |
| sai->pinctrl = devm_pinctrl_get(&pdev->dev); |
| |
| platform_set_drvdata(pdev, sai); |
| pm_runtime_enable(dev); |
| if (!pm_runtime_enabled(dev)) { |
| ret = fsl_sai_runtime_resume(dev); |
| if (ret) |
| goto err_pm_disable; |
| } |
| |
| ret = pm_runtime_resume_and_get(dev); |
| if (ret < 0) |
| goto err_pm_get_sync; |
| |
| /* Get sai version */ |
| ret = fsl_sai_check_version(dev); |
| if (ret < 0) |
| dev_warn(dev, "Error reading SAI version: %d\n", ret); |
| |
| /* Select MCLK direction */ |
| if (sai->mclk_direction_output && |
| sai->soc_data->max_register >= FSL_SAI_MCTL) { |
| regmap_update_bits(sai->regmap, FSL_SAI_MCTL, |
| FSL_SAI_MCTL_MCLK_EN, FSL_SAI_MCTL_MCLK_EN); |
| } |
| |
| ret = pm_runtime_put_sync(dev); |
| if (ret < 0 && ret != -ENOSYS) |
| goto err_pm_get_sync; |
| |
| /* |
| * Register platform component before registering cpu dai for there |
| * is not defer probe for platform component in snd_soc_add_pcm_runtime(). |
| */ |
| if (sai->soc_data->use_imx_pcm) { |
| ret = imx_pcm_dma_init(pdev); |
| if (ret) { |
| dev_err_probe(dev, ret, "PCM DMA init failed\n"); |
| if (!IS_ENABLED(CONFIG_SND_SOC_IMX_PCM_DMA)) |
| dev_err(dev, "Error: You must enable the imx-pcm-dma support!\n"); |
| goto err_pm_get_sync; |
| } |
| } else { |
| ret = devm_snd_dmaengine_pcm_register(dev, NULL, 0); |
| if (ret) { |
| dev_err_probe(dev, ret, "Registering PCM dmaengine failed\n"); |
| goto err_pm_get_sync; |
| } |
| } |
| |
| ret = devm_snd_soc_register_component(dev, &fsl_component, |
| sai->cpu_dai_drv, ARRAY_SIZE(fsl_sai_dai_template)); |
| if (ret) |
| goto err_pm_get_sync; |
| |
| return ret; |
| |
| err_pm_get_sync: |
| if (!pm_runtime_status_suspended(dev)) |
| fsl_sai_runtime_suspend(dev); |
| err_pm_disable: |
| pm_runtime_disable(dev); |
| |
| return ret; |
| } |
| |
| static void fsl_sai_remove(struct platform_device *pdev) |
| { |
| pm_runtime_disable(&pdev->dev); |
| if (!pm_runtime_status_suspended(&pdev->dev)) |
| fsl_sai_runtime_suspend(&pdev->dev); |
| } |
| |
| static const struct fsl_sai_soc_data fsl_sai_vf610_data = { |
| .use_imx_pcm = false, |
| .use_edma = false, |
| .fifo_depth = 32, |
| .pins = 1, |
| .reg_offset = 0, |
| .mclk0_is_mclk1 = false, |
| .flags = 0, |
| .max_register = FSL_SAI_RMR, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx6sx_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 32, |
| .pins = 1, |
| .reg_offset = 0, |
| .mclk0_is_mclk1 = true, |
| .flags = 0, |
| .max_register = FSL_SAI_RMR, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx7ulp_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 16, |
| .pins = 2, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .flags = PMQOS_CPU_LATENCY, |
| .max_register = FSL_SAI_RMR, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8mq_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 128, |
| .pins = 8, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .flags = 0, |
| .max_register = FSL_SAI_RMR, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8qm_data = { |
| .use_imx_pcm = true, |
| .use_edma = true, |
| .fifo_depth = 64, |
| .pins = 4, |
| .reg_offset = 0, |
| .mclk0_is_mclk1 = false, |
| .flags = 0, |
| .max_register = FSL_SAI_RMR, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8mm_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 128, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 8, |
| .flags = 0, |
| .max_register = FSL_SAI_MCTL, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8mn_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 128, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 8, |
| .flags = 0, |
| .max_register = FSL_SAI_MDIV, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8mp_data = { |
| .use_imx_pcm = true, |
| .use_edma = false, |
| .fifo_depth = 128, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 8, |
| .flags = 0, |
| .max_register = FSL_SAI_MDIV, |
| .mclk_with_tere = true, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx8ulp_data = { |
| .use_imx_pcm = true, |
| .use_edma = true, |
| .fifo_depth = 16, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 4, |
| .flags = PMQOS_CPU_LATENCY, |
| .max_register = FSL_SAI_RTCAP, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx93_data = { |
| .use_imx_pcm = true, |
| .use_edma = true, |
| .fifo_depth = 128, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 4, |
| .flags = 0, |
| .max_register = FSL_SAI_MCTL, |
| .max_burst = {8, 8}, |
| }; |
| |
| static const struct fsl_sai_soc_data fsl_sai_imx95_data = { |
| .use_imx_pcm = true, |
| .use_edma = true, |
| .fifo_depth = 128, |
| .reg_offset = 8, |
| .mclk0_is_mclk1 = false, |
| .pins = 8, |
| .flags = 0, |
| .max_register = FSL_SAI_MCTL, |
| .max_burst = {8, 8}, |
| }; |
| |
| static const struct of_device_id fsl_sai_ids[] = { |
| { .compatible = "fsl,vf610-sai", .data = &fsl_sai_vf610_data }, |
| { .compatible = "fsl,imx6sx-sai", .data = &fsl_sai_imx6sx_data }, |
| { .compatible = "fsl,imx6ul-sai", .data = &fsl_sai_imx6sx_data }, |
| { .compatible = "fsl,imx7ulp-sai", .data = &fsl_sai_imx7ulp_data }, |
| { .compatible = "fsl,imx8mq-sai", .data = &fsl_sai_imx8mq_data }, |
| { .compatible = "fsl,imx8qm-sai", .data = &fsl_sai_imx8qm_data }, |
| { .compatible = "fsl,imx8mm-sai", .data = &fsl_sai_imx8mm_data }, |
| { .compatible = "fsl,imx8mp-sai", .data = &fsl_sai_imx8mp_data }, |
| { .compatible = "fsl,imx8ulp-sai", .data = &fsl_sai_imx8ulp_data }, |
| { .compatible = "fsl,imx8mn-sai", .data = &fsl_sai_imx8mn_data }, |
| { .compatible = "fsl,imx93-sai", .data = &fsl_sai_imx93_data }, |
| { .compatible = "fsl,imx95-sai", .data = &fsl_sai_imx95_data }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, fsl_sai_ids); |
| |
| static int fsl_sai_runtime_suspend(struct device *dev) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_CAPTURE)) |
| clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[0]]); |
| |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_PLAYBACK)) |
| clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[1]]); |
| |
| clk_disable_unprepare(sai->bus_clk); |
| |
| if (sai->soc_data->flags & PMQOS_CPU_LATENCY) |
| cpu_latency_qos_remove_request(&sai->pm_qos_req); |
| |
| regcache_cache_only(sai->regmap, true); |
| |
| return 0; |
| } |
| |
| static int fsl_sai_runtime_resume(struct device *dev) |
| { |
| struct fsl_sai *sai = dev_get_drvdata(dev); |
| unsigned int ofs = sai->soc_data->reg_offset; |
| int ret; |
| |
| ret = clk_prepare_enable(sai->bus_clk); |
| if (ret) { |
| dev_err(dev, "failed to enable bus clock: %d\n", ret); |
| return ret; |
| } |
| |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_PLAYBACK)) { |
| ret = clk_prepare_enable(sai->mclk_clk[sai->mclk_id[1]]); |
| if (ret) |
| goto disable_bus_clk; |
| } |
| |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_CAPTURE)) { |
| ret = clk_prepare_enable(sai->mclk_clk[sai->mclk_id[0]]); |
| if (ret) |
| goto disable_tx_clk; |
| } |
| |
| if (sai->soc_data->flags & PMQOS_CPU_LATENCY) |
| cpu_latency_qos_add_request(&sai->pm_qos_req, 0); |
| |
| regcache_cache_only(sai->regmap, false); |
| regcache_mark_dirty(sai->regmap); |
| regmap_write(sai->regmap, FSL_SAI_TCSR(ofs), FSL_SAI_CSR_SR); |
| regmap_write(sai->regmap, FSL_SAI_RCSR(ofs), FSL_SAI_CSR_SR); |
| usleep_range(1000, 2000); |
| regmap_write(sai->regmap, FSL_SAI_TCSR(ofs), 0); |
| regmap_write(sai->regmap, FSL_SAI_RCSR(ofs), 0); |
| |
| ret = regcache_sync(sai->regmap); |
| if (ret) |
| goto disable_rx_clk; |
| |
| if (sai->soc_data->mclk_with_tere && sai->mclk_direction_output) |
| regmap_update_bits(sai->regmap, FSL_SAI_TCSR(ofs), |
| FSL_SAI_CSR_TERE, FSL_SAI_CSR_TERE); |
| |
| return 0; |
| |
| disable_rx_clk: |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_CAPTURE)) |
| clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[0]]); |
| disable_tx_clk: |
| if (sai->mclk_streams & BIT(SNDRV_PCM_STREAM_PLAYBACK)) |
| clk_disable_unprepare(sai->mclk_clk[sai->mclk_id[1]]); |
| disable_bus_clk: |
| clk_disable_unprepare(sai->bus_clk); |
| |
| return ret; |
| } |
| |
| static const struct dev_pm_ops fsl_sai_pm_ops = { |
| SET_RUNTIME_PM_OPS(fsl_sai_runtime_suspend, |
| fsl_sai_runtime_resume, NULL) |
| SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, |
| pm_runtime_force_resume) |
| }; |
| |
| static struct platform_driver fsl_sai_driver = { |
| .probe = fsl_sai_probe, |
| .remove = fsl_sai_remove, |
| .driver = { |
| .name = "fsl-sai", |
| .pm = &fsl_sai_pm_ops, |
| .of_match_table = fsl_sai_ids, |
| }, |
| }; |
| module_platform_driver(fsl_sai_driver); |
| |
| MODULE_DESCRIPTION("Freescale Soc SAI Interface"); |
| MODULE_AUTHOR("Xiubo Li, <Li.Xiubo@freescale.com>"); |
| MODULE_ALIAS("platform:fsl-sai"); |
| MODULE_LICENSE("GPL"); |