| #include "qcom-msm8974.dtsi" |
| #include "qcom-pm8841.dtsi" |
| #include "qcom-pm8941.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| |
| / { |
| model = "Fairphone 2"; |
| compatible = "fairphone,fp2", "qcom,msm8974"; |
| |
| aliases { |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| input-name = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| camera-snapshot { |
| label = "camera_snapshot"; |
| gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_CAMERA>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| volume-down { |
| label = "volume_down"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| |
| volume-up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| wakeup-source; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| vibrator { |
| compatible = "gpio-vibrator"; |
| enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>; |
| vcc-supply = <&pm8941_l18>; |
| }; |
| |
| smd { |
| rpm { |
| rpm_requests { |
| pm8841-regulators { |
| s1 { |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| s2 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1050000>; |
| }; |
| }; |
| |
| pm8941-regulators { |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| |
| regulator-boot-on; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l3 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l11 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l19 { |
| regulator-min-microvolt = <2900000>; |
| regulator-max-microvolt = <3350000>; |
| }; |
| |
| l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| regulator-system-load = <200000>; |
| regulator-allow-set-load; |
| }; |
| |
| l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l23 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &soc { |
| serial@f991e000 { |
| status = "ok"; |
| }; |
| |
| remoteproc@fb21b000 { |
| status = "ok"; |
| |
| vddmx-supply = <&pm8841_s1>; |
| vddcx-supply = <&pm8841_s2>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wcnss_pin_a>; |
| |
| smd-edge { |
| qcom,remote-pid = <4>; |
| label = "pronto"; |
| |
| wcnss { |
| status = "ok"; |
| }; |
| }; |
| }; |
| |
| pinctrl@fd510000 { |
| sdhc1_pin_a: sdhc1-pin-active { |
| clk { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc2_pin_a: sdhc2-pin-active { |
| clk { |
| pins = "sdc2_clk"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| wcnss_pin_a: wcnss-pin-active { |
| wlan { |
| pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40"; |
| function = "wlan"; |
| |
| drive-strength = <6>; |
| bias-pull-down; |
| }; |
| |
| bt { |
| pins = "gpio35", "gpio43", "gpio44"; |
| function = "bt"; |
| |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| fm { |
| pins = "gpio41", "gpio42"; |
| function = "fm"; |
| |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| sdhci@f9824900 { |
| status = "ok"; |
| |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| bus-width = <8>; |
| non-removable; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc1_pin_a>; |
| }; |
| |
| sdhci@f98a4900 { |
| status = "ok"; |
| |
| vmmc-supply = <&pm8941_l21>; |
| vqmmc-supply = <&pm8941_l13>; |
| |
| bus-width = <4>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc2_pin_a>; |
| }; |
| |
| usb@f9a55000 { |
| status = "ok"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| extcon = <&smbb>, <&usb_id>; |
| vbus-supply = <&chg_otg>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| ulpi { |
| phy@a { |
| status = "ok"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| extcon = <&smbb>; |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
| }; |
| }; |
| |
| imem@fe805000 { |
| status = "okay"; |
| |
| reboot-mode { |
| mode-normal = <0x77665501>; |
| mode-bootloader = <0x77665500>; |
| mode-recovery = <0x77665502>; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pm8941@0 { |
| gpios@c000 { |
| gpio_keys_pin_a: gpio-keys-active { |
| pins = "gpio1", "gpio2", "gpio5"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| }; |
| }; |
| }; |
