| // SPDX-License-Identifier: GPL-2.0 | |
| #include <linux/init.h> | |
| #include <linux/clocksource.h> | |
| #include <linux/clockchips.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/ioport.h> | |
| #include <linux/io.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/sched_clock.h> | |
| #include <linux/syscore_ops.h> | |
| #include <soc/at91/atmel_tcb.h> | |
| /* | |
| * We're configured to use a specific TC block, one that's not hooked | |
| * up to external hardware, to provide a time solution: | |
| * | |
| * - Two channels combine to create a free-running 32 bit counter | |
| * with a base rate of 5+ MHz, packaged as a clocksource (with | |
| * resolution better than 200 nsec). | |
| * - Some chips support 32 bit counter. A single channel is used for | |
| * this 32 bit free-running counter. the second channel is not used. | |
| * | |
| * - The third channel may be used to provide a clockevent source, used in | |
| * either periodic or oneshot mode. For 16-bit counter its runs at 32 KiHZ, | |
| * and can handle delays of up to two seconds. For 32-bit counters, it runs at | |
| * the same rate as the clocksource | |
| * | |
| * REVISIT behavior during system suspend states... we should disable | |
| * all clocks and save the power. Easily done for clockevent devices, | |
| * but clocksources won't necessarily get the needed notifications. | |
| * For deeper system sleep states, this will be mandatory... | |
| */ | |
| static void __iomem *tcaddr; | |
| static struct | |
| { | |
| u32 cmr; | |
| u32 imr; | |
| u32 rc; | |
| bool clken; | |
| } tcb_cache[3]; | |
| static u32 bmr_cache; | |
| static const u8 atmel_tcb_divisors[] = { 2, 8, 32, 128 }; | |
| static u64 tc_get_cycles(struct clocksource *cs) | |
| { | |
| unsigned long flags; | |
| u32 lower, upper; | |
| raw_local_irq_save(flags); | |
| do { | |
| upper = readl_relaxed(tcaddr + ATMEL_TC_REG(1, CV)); | |
| lower = readl_relaxed(tcaddr + ATMEL_TC_REG(0, CV)); | |
| } while (upper != readl_relaxed(tcaddr + ATMEL_TC_REG(1, CV))); | |
| raw_local_irq_restore(flags); | |
| return (upper << 16) | lower; | |
| } | |
| static u64 tc_get_cycles32(struct clocksource *cs) | |
| { | |
| return readl_relaxed(tcaddr + ATMEL_TC_REG(0, CV)); | |
| } | |
| static void tc_clksrc_suspend(struct clocksource *cs) | |
| { | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(tcb_cache); i++) { | |
| tcb_cache[i].cmr = readl(tcaddr + ATMEL_TC_REG(i, CMR)); | |
| tcb_cache[i].imr = readl(tcaddr + ATMEL_TC_REG(i, IMR)); | |
| tcb_cache[i].rc = readl(tcaddr + ATMEL_TC_REG(i, RC)); | |
| tcb_cache[i].clken = !!(readl(tcaddr + ATMEL_TC_REG(i, SR)) & | |
| ATMEL_TC_CLKSTA); | |
| } | |
| bmr_cache = readl(tcaddr + ATMEL_TC_BMR); | |
| } | |
| static void tc_clksrc_resume(struct clocksource *cs) | |
| { | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(tcb_cache); i++) { | |
| /* Restore registers for the channel, RA and RB are not used */ | |
| writel(tcb_cache[i].cmr, tcaddr + ATMEL_TC_REG(i, CMR)); | |
| writel(tcb_cache[i].rc, tcaddr + ATMEL_TC_REG(i, RC)); | |
| writel(0, tcaddr + ATMEL_TC_REG(i, RA)); | |
| writel(0, tcaddr + ATMEL_TC_REG(i, RB)); | |
| /* Disable all the interrupts */ | |
| writel(0xff, tcaddr + ATMEL_TC_REG(i, IDR)); | |
| /* Reenable interrupts that were enabled before suspending */ | |
| writel(tcb_cache[i].imr, tcaddr + ATMEL_TC_REG(i, IER)); | |
| /* Start the clock if it was used */ | |
| if (tcb_cache[i].clken) | |
| writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(i, CCR)); | |
| } | |
| /* Dual channel, chain channels */ | |
| writel(bmr_cache, tcaddr + ATMEL_TC_BMR); | |
| /* Finally, trigger all the channels*/ | |
| writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR); | |
| } | |
| static struct clocksource clksrc = { | |
| .rating = 200, | |
| .read = tc_get_cycles, | |
| .mask = CLOCKSOURCE_MASK(32), | |
| .flags = CLOCK_SOURCE_IS_CONTINUOUS, | |
| .suspend = tc_clksrc_suspend, | |
| .resume = tc_clksrc_resume, | |
| }; | |
| static u64 notrace tc_sched_clock_read(void) | |
| { | |
| return tc_get_cycles(&clksrc); | |
| } | |
| static u64 notrace tc_sched_clock_read32(void) | |
| { | |
| return tc_get_cycles32(&clksrc); | |
| } | |
| static struct delay_timer tc_delay_timer; | |
| static unsigned long tc_delay_timer_read(void) | |
| { | |
| return tc_get_cycles(&clksrc); | |
| } | |
| static unsigned long notrace tc_delay_timer_read32(void) | |
| { | |
| return tc_get_cycles32(&clksrc); | |
| } | |
| #ifdef CONFIG_GENERIC_CLOCKEVENTS | |
| struct tc_clkevt_device { | |
| struct clock_event_device clkevt; | |
| struct clk *clk; | |
| u32 rate; | |
| void __iomem *regs; | |
| }; | |
| static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt) | |
| { | |
| return container_of(clkevt, struct tc_clkevt_device, clkevt); | |
| } | |
| static u32 timer_clock; | |
| static int tc_shutdown(struct clock_event_device *d) | |
| { | |
| struct tc_clkevt_device *tcd = to_tc_clkevt(d); | |
| void __iomem *regs = tcd->regs; | |
| writel(0xff, regs + ATMEL_TC_REG(2, IDR)); | |
| writel(ATMEL_TC_CLKDIS, regs + ATMEL_TC_REG(2, CCR)); | |
| if (!clockevent_state_detached(d)) | |
| clk_disable(tcd->clk); | |
| return 0; | |
| } | |
| static int tc_set_oneshot(struct clock_event_device *d) | |
| { | |
| struct tc_clkevt_device *tcd = to_tc_clkevt(d); | |
| void __iomem *regs = tcd->regs; | |
| if (clockevent_state_oneshot(d) || clockevent_state_periodic(d)) | |
| tc_shutdown(d); | |
| clk_enable(tcd->clk); | |
| /* count up to RC, then irq and stop */ | |
| writel(timer_clock | ATMEL_TC_CPCSTOP | ATMEL_TC_WAVE | | |
| ATMEL_TC_WAVESEL_UP_AUTO, regs + ATMEL_TC_REG(2, CMR)); | |
| writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER)); | |
| /* set_next_event() configures and starts the timer */ | |
| return 0; | |
| } | |
| static int tc_set_periodic(struct clock_event_device *d) | |
| { | |
| struct tc_clkevt_device *tcd = to_tc_clkevt(d); | |
| void __iomem *regs = tcd->regs; | |
| if (clockevent_state_oneshot(d) || clockevent_state_periodic(d)) | |
| tc_shutdown(d); | |
| /* By not making the gentime core emulate periodic mode on top | |
| * of oneshot, we get lower overhead and improved accuracy. | |
| */ | |
| clk_enable(tcd->clk); | |
| /* count up to RC, then irq and restart */ | |
| writel(timer_clock | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO, | |
| regs + ATMEL_TC_REG(2, CMR)); | |
| writel((tcd->rate + HZ / 2) / HZ, tcaddr + ATMEL_TC_REG(2, RC)); | |
| /* Enable clock and interrupts on RC compare */ | |
| writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER)); | |
| /* go go gadget! */ | |
| writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG, regs + | |
| ATMEL_TC_REG(2, CCR)); | |
| return 0; | |
| } | |
| static int tc_next_event(unsigned long delta, struct clock_event_device *d) | |
| { | |
| writel_relaxed(delta, tcaddr + ATMEL_TC_REG(2, RC)); | |
| /* go go gadget! */ | |
| writel_relaxed(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG, | |
| tcaddr + ATMEL_TC_REG(2, CCR)); | |
| return 0; | |
| } | |
| static struct tc_clkevt_device clkevt = { | |
| .clkevt = { | |
| .features = CLOCK_EVT_FEAT_PERIODIC | | |
| CLOCK_EVT_FEAT_ONESHOT, | |
| /* Should be lower than at91rm9200's system timer */ | |
| .rating = 125, | |
| .set_next_event = tc_next_event, | |
| .set_state_shutdown = tc_shutdown, | |
| .set_state_periodic = tc_set_periodic, | |
| .set_state_oneshot = tc_set_oneshot, | |
| }, | |
| }; | |
| static irqreturn_t ch2_irq(int irq, void *handle) | |
| { | |
| struct tc_clkevt_device *dev = handle; | |
| unsigned int sr; | |
| sr = readl_relaxed(dev->regs + ATMEL_TC_REG(2, SR)); | |
| if (sr & ATMEL_TC_CPCS) { | |
| dev->clkevt.event_handler(&dev->clkevt); | |
| return IRQ_HANDLED; | |
| } | |
| return IRQ_NONE; | |
| } | |
| static int __init setup_clkevents(struct atmel_tc *tc, int divisor_idx) | |
| { | |
| int ret; | |
| struct clk *t2_clk = tc->clk[2]; | |
| int irq = tc->irq[2]; | |
| int bits = tc->tcb_config->counter_width; | |
| /* try to enable t2 clk to avoid future errors in mode change */ | |
| ret = clk_prepare_enable(t2_clk); | |
| if (ret) | |
| return ret; | |
| clkevt.regs = tc->regs; | |
| clkevt.clk = t2_clk; | |
| if (bits == 32) { | |
| timer_clock = divisor_idx; | |
| clkevt.rate = clk_get_rate(t2_clk) / atmel_tcb_divisors[divisor_idx]; | |
| } else { | |
| ret = clk_prepare_enable(tc->slow_clk); | |
| if (ret) { | |
| clk_disable_unprepare(t2_clk); | |
| return ret; | |
| } | |
| clkevt.rate = clk_get_rate(tc->slow_clk); | |
| timer_clock = ATMEL_TC_TIMER_CLOCK5; | |
| } | |
| clk_disable(t2_clk); | |
| clkevt.clkevt.cpumask = cpumask_of(0); | |
| ret = request_irq(irq, ch2_irq, IRQF_TIMER, "tc_clkevt", &clkevt); | |
| if (ret) { | |
| clk_unprepare(t2_clk); | |
| if (bits != 32) | |
| clk_disable_unprepare(tc->slow_clk); | |
| return ret; | |
| } | |
| clockevents_config_and_register(&clkevt.clkevt, clkevt.rate, 1, BIT(bits) - 1); | |
| return ret; | |
| } | |
| #else /* !CONFIG_GENERIC_CLOCKEVENTS */ | |
| static int __init setup_clkevents(struct atmel_tc *tc, int divisor_idx) | |
| { | |
| /* NOTHING */ | |
| return 0; | |
| } | |
| #endif | |
| static void __init tcb_setup_dual_chan(struct atmel_tc *tc, int mck_divisor_idx) | |
| { | |
| /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */ | |
| writel(mck_divisor_idx /* likely divide-by-8 */ | |
| | ATMEL_TC_WAVE | |
| | ATMEL_TC_WAVESEL_UP /* free-run */ | |
| | ATMEL_TC_ASWTRG_SET /* TIOA0 rises at software trigger */ | |
| | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */ | |
| | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */ | |
| tcaddr + ATMEL_TC_REG(0, CMR)); | |
| writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA)); | |
| writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC)); | |
| writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */ | |
| writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR)); | |
| /* channel 1: waveform mode, input TIOA0 */ | |
| writel(ATMEL_TC_XC1 /* input: TIOA0 */ | |
| | ATMEL_TC_WAVE | |
| | ATMEL_TC_WAVESEL_UP, /* free-run */ | |
| tcaddr + ATMEL_TC_REG(1, CMR)); | |
| writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */ | |
| writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR)); | |
| /* chain channel 0 to channel 1*/ | |
| writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR); | |
| /* then reset all the timers */ | |
| writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR); | |
| } | |
| static void __init tcb_setup_single_chan(struct atmel_tc *tc, int mck_divisor_idx) | |
| { | |
| /* channel 0: waveform mode, input mclk/8 */ | |
| writel(mck_divisor_idx /* likely divide-by-8 */ | |
| | ATMEL_TC_WAVE | |
| | ATMEL_TC_WAVESEL_UP, /* free-run */ | |
| tcaddr + ATMEL_TC_REG(0, CMR)); | |
| writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */ | |
| writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR)); | |
| /* then reset all the timers */ | |
| writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR); | |
| } | |
| static struct atmel_tcb_config tcb_rm9200_config = { | |
| .counter_width = 16, | |
| }; | |
| static struct atmel_tcb_config tcb_sam9x5_config = { | |
| .counter_width = 32, | |
| }; | |
| static struct atmel_tcb_config tcb_sama5d2_config = { | |
| .counter_width = 32, | |
| .has_gclk = 1, | |
| }; | |
| static const struct of_device_id atmel_tcb_of_match[] = { | |
| { .compatible = "atmel,at91rm9200-tcb", .data = &tcb_rm9200_config, }, | |
| { .compatible = "atmel,at91sam9x5-tcb", .data = &tcb_sam9x5_config, }, | |
| { .compatible = "atmel,sama5d2-tcb", .data = &tcb_sama5d2_config, }, | |
| { /* sentinel */ } | |
| }; | |
| static int __init tcb_clksrc_init(struct device_node *node) | |
| { | |
| struct atmel_tc tc; | |
| struct clk *t0_clk; | |
| const struct of_device_id *match; | |
| u64 (*tc_sched_clock)(void); | |
| u32 rate, divided_rate = 0; | |
| int best_divisor_idx = -1; | |
| int bits; | |
| int i; | |
| int ret; | |
| /* Protect against multiple calls */ | |
| if (tcaddr) | |
| return 0; | |
| tc.regs = of_iomap(node->parent, 0); | |
| if (!tc.regs) | |
| return -ENXIO; | |
| t0_clk = of_clk_get_by_name(node->parent, "t0_clk"); | |
| if (IS_ERR(t0_clk)) | |
| return PTR_ERR(t0_clk); | |
| tc.slow_clk = of_clk_get_by_name(node->parent, "slow_clk"); | |
| if (IS_ERR(tc.slow_clk)) | |
| return PTR_ERR(tc.slow_clk); | |
| tc.clk[0] = t0_clk; | |
| tc.clk[1] = of_clk_get_by_name(node->parent, "t1_clk"); | |
| if (IS_ERR(tc.clk[1])) | |
| tc.clk[1] = t0_clk; | |
| tc.clk[2] = of_clk_get_by_name(node->parent, "t2_clk"); | |
| if (IS_ERR(tc.clk[2])) | |
| tc.clk[2] = t0_clk; | |
| tc.irq[2] = of_irq_get(node->parent, 2); | |
| if (tc.irq[2] <= 0) { | |
| tc.irq[2] = of_irq_get(node->parent, 0); | |
| if (tc.irq[2] <= 0) | |
| return -EINVAL; | |
| } | |
| match = of_match_node(atmel_tcb_of_match, node->parent); | |
| if (!match) | |
| return -ENODEV; | |
| tc.tcb_config = match->data; | |
| bits = tc.tcb_config->counter_width; | |
| for (i = 0; i < ARRAY_SIZE(tc.irq); i++) | |
| writel(ATMEL_TC_ALL_IRQ, tc.regs + ATMEL_TC_REG(i, IDR)); | |
| ret = clk_prepare_enable(t0_clk); | |
| if (ret) { | |
| pr_debug("can't enable T0 clk\n"); | |
| return ret; | |
| } | |
| /* How fast will we be counting? Pick something over 5 MHz. */ | |
| rate = (u32) clk_get_rate(t0_clk); | |
| i = 0; | |
| if (tc.tcb_config->has_gclk) | |
| i = 1; | |
| for (; i < ARRAY_SIZE(atmel_tcb_divisors); i++) { | |
| unsigned divisor = atmel_tcb_divisors[i]; | |
| unsigned tmp; | |
| tmp = rate / divisor; | |
| pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp); | |
| if ((best_divisor_idx >= 0) && (tmp < 5 * 1000 * 1000)) | |
| break; | |
| divided_rate = tmp; | |
| best_divisor_idx = i; | |
| } | |
| clksrc.name = kbasename(node->parent->full_name); | |
| clkevt.clkevt.name = kbasename(node->parent->full_name); | |
| pr_debug("%s at %d.%03d MHz\n", clksrc.name, divided_rate / 1000000, | |
| ((divided_rate % 1000000) + 500) / 1000); | |
| tcaddr = tc.regs; | |
| if (bits == 32) { | |
| /* use appropriate function to read 32 bit counter */ | |
| clksrc.read = tc_get_cycles32; | |
| /* setup only channel 0 */ | |
| tcb_setup_single_chan(&tc, best_divisor_idx); | |
| tc_sched_clock = tc_sched_clock_read32; | |
| tc_delay_timer.read_current_timer = tc_delay_timer_read32; | |
| } else { | |
| /* we have three clocks no matter what the | |
| * underlying platform supports. | |
| */ | |
| ret = clk_prepare_enable(tc.clk[1]); | |
| if (ret) { | |
| pr_debug("can't enable T1 clk\n"); | |
| goto err_disable_t0; | |
| } | |
| /* setup both channel 0 & 1 */ | |
| tcb_setup_dual_chan(&tc, best_divisor_idx); | |
| tc_sched_clock = tc_sched_clock_read; | |
| tc_delay_timer.read_current_timer = tc_delay_timer_read; | |
| } | |
| /* and away we go! */ | |
| ret = clocksource_register_hz(&clksrc, divided_rate); | |
| if (ret) | |
| goto err_disable_t1; | |
| /* channel 2: periodic and oneshot timer support */ | |
| ret = setup_clkevents(&tc, best_divisor_idx); | |
| if (ret) | |
| goto err_unregister_clksrc; | |
| sched_clock_register(tc_sched_clock, 32, divided_rate); | |
| tc_delay_timer.freq = divided_rate; | |
| register_current_timer_delay(&tc_delay_timer); | |
| return 0; | |
| err_unregister_clksrc: | |
| clocksource_unregister(&clksrc); | |
| err_disable_t1: | |
| if (bits != 32) | |
| clk_disable_unprepare(tc.clk[1]); | |
| err_disable_t0: | |
| clk_disable_unprepare(t0_clk); | |
| tcaddr = NULL; | |
| return ret; | |
| } | |
| TIMER_OF_DECLARE(atmel_tcb_clksrc, "atmel,tcb-timer", tcb_clksrc_init); |