| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Support for the i.MX6-based Bosch ACC board. |
| * |
| * Copyright (C) 2016 Garz & Fricke GmbH |
| * Copyright (C) 2018 DENX Software Engineering GmbH, Heiko Schocher <hs@denx.de> |
| * Copyright (C) 2018 DENX Software Engineering GmbH, Niel Fourie <lusus@denx.de> |
| * Copyright (C) 2019-2021 Bosch Thermotechnik GmbH, Matthias Winker <matthias.winker@bosch.com> |
| * Copyright (C) 2022 DENX Software Engineering GmbH, Philip Oberfichtner <pro@denx.de> |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include "imx6q.dtsi" |
| |
| / { |
| model = "Bosch ACC"; |
| compatible = "bosch,imx6q-acc", "fsl,imx6q"; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| mmc0 = &usdhc4; |
| mmc1 = &usdhc2; |
| serial0 = &uart2; |
| serial1 = &uart1; |
| }; |
| |
| memory@10000000 { |
| device_type = "memory"; |
| reg = <0x10000000 0x40000000>; |
| }; |
| |
| backlight_lvds: backlight-lvds { |
| compatible = "pwm-backlight"; |
| pwms = <&pwm1 0 200000>; |
| brightness-levels = <0 61 499 1706 4079 8022 13938 22237 33328 47623 65535>; |
| num-interpolated-steps = <10>; |
| default-brightness-level = <60>; |
| power-supply = <®_lcd>; |
| }; |
| |
| panel { |
| compatible = "dataimage,fg1001l0dsswmg01"; |
| backlight = <&backlight_lvds>; |
| |
| port { |
| panel_in: endpoint { |
| remote-endpoint = <&lvds0_out>; |
| }; |
| }; |
| }; |
| |
| refclk: refclk { |
| compatible = "fixed-factor-clock"; |
| #clock-cells = <0>; |
| clocks = <&clks IMX6QDL_CLK_CKO2>; |
| clock-div = <1>; |
| clock-mult = <1>; |
| clock-output-names = "12mhz_refclk"; |
| assigned-clocks = <&clks IMX6QDL_CLK_CKO>, |
| <&clks IMX6QDL_CLK_CKO2>, |
| <&clks IMX6QDL_CLK_CKO2_SEL>; |
| assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>, |
| <&clks IMX6QDL_CLK_CKO2_PODF>, |
| <&clks IMX6QDL_CLK_OSC>; |
| assigned-clock-rates = <0>, <12000000>, <0>; |
| }; |
| |
| cpus { |
| cpu0: cpu@0 { |
| operating-points = < |
| /* kHz uV */ |
| 1200000 1275000 |
| 996000 1225000 |
| 852000 1225000 |
| 792000 1150000 |
| 396000 950000 |
| >; |
| fsl,soc-operating-points = < |
| /* ARM kHz SOC-PU uV */ |
| 1200000 1225000 |
| 996000 1175000 |
| 852000 1175000 |
| 792000 1150000 |
| 396000 1150000 |
| >; |
| }; |
| |
| cpu1: cpu@1 { |
| operating-points = < |
| /* kHz uV */ |
| 1200000 1275000 |
| 996000 1225000 |
| 852000 1225000 |
| 792000 1150000 |
| 396000 950000 |
| >; |
| fsl,soc-operating-points = < |
| /* ARM kHz SOC-PU uV */ |
| 1200000 1225000 |
| 996000 1175000 |
| 852000 1175000 |
| 792000 1150000 |
| 396000 1150000 |
| >; |
| }; |
| }; |
| |
| pwm-leds { |
| compatible = "pwm-leds"; |
| |
| led_red: led-0 { |
| color = <LED_COLOR_ID_RED>; |
| max-brightness = <248>; |
| default-state = "off"; |
| pwms = <&pwm2 0 500000>; |
| }; |
| |
| led_white: led-1 { |
| color = <LED_COLOR_ID_WHITE>; |
| max-brightness = <248>; |
| default-state = "off"; |
| pwms = <&pwm3 0 500000>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reset_gpio_led>; |
| |
| led-2 { |
| color = <LED_COLOR_ID_RED>; |
| gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| }; |
| }; |
| |
| reg_5p0: regulator-5p0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "5p0"; |
| }; |
| |
| reg_vin: regulator-vin { |
| compatible = "regulator-fixed"; |
| regulator-name = "VIN"; |
| regulator-min-microvolt = <4500000>; |
| regulator-max-microvolt = <4500000>; |
| regulator-always-on; |
| vin-supply = <®_5p0>; |
| }; |
| |
| reg_usb_otg_vbus: regulator-usb-otg-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_otg_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| reg_usb_h1_vbus: regulator-usb-h1-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_h1_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| vin-supply = <®_5p0>; |
| }; |
| |
| reg_usb_h2_vbus: regulator-usb-h2-vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_h2_vbus"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <®_5p0> ; |
| regulator-always-on; |
| }; |
| |
| reg_vsnvs: regulator-vsnvs { |
| compatible = "regulator-fixed"; |
| regulator-name = "VSNVS_3V0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-always-on; |
| vin-supply = <®_5p0>; |
| }; |
| |
| reg_lcd: regulator-lcd { |
| compatible = "regulator-fixed"; |
| regulator-name = "LCD0 POWER"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lcd_enable>; |
| gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-boot-on; |
| }; |
| |
| reg_dac: regulator-dac { |
| compatible = "regulator-fixed"; |
| regulator-name = "vref_dac"; |
| regulator-min-microvolt = <20000>; |
| regulator-max-microvolt = <20000>; |
| vin-supply = <®_5p0> ; |
| regulator-boot-on; |
| }; |
| |
| reg_sw4: regulator-sw4 { |
| compatible = "regulator-fixed"; |
| regulator-name = "SW4_3V3"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| vin-supply = <®_5p0>; |
| }; |
| |
| reg_sys: regulator-sys { |
| compatible = "regulator-fixed"; |
| regulator-name = "SYS_4V2"; |
| regulator-min-microvolt = <4200000>; |
| regulator-max-microvolt = <4200000>; |
| regulator-always-on; |
| vin-supply = <®_5p0>; |
| }; |
| }; |
| |
| ®_arm { |
| vin-supply = <&sw2_reg>; |
| }; |
| |
| ®_soc { |
| vin-supply = <&sw1c_reg>; |
| }; |
| |
| ®_vdd1p1 { |
| vin-supply = <®_vsnvs>; |
| }; |
| |
| ®_vdd2p5 { |
| vin-supply = <®_vsnvs>; |
| }; |
| |
| ®_vdd3p0 { |
| vin-supply = <®_vsnvs>; |
| }; |
| |
| &fec { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_enet>; |
| clocks = <&clks IMX6QDL_CLK_ENET>, |
| <&clks IMX6QDL_CLK_ENET>, |
| <&clks IMX6QDL_CLK_ENET>, |
| <&clks IMX6QDL_CLK_ENET_REF>; |
| clock-names = "ipg", "ahb", "ptp", "enet_out"; |
| phy-mode = "rmii"; |
| phy-supply = <®_sw4>; |
| phy-handle = <ðphy>; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <23 IRQ_TYPE_EDGE_FALLING>; |
| smsc,disable-energy-detect; |
| }; |
| }; |
| }; |
| |
| &gpu_vg { |
| status = "disabled"; |
| }; |
| |
| &gpu_2d { |
| status = "disabled"; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| pmic: pmic@8 { |
| compatible = "fsl,pfuze100"; |
| reg = <0x08>; |
| |
| regulators { |
| sw1c_reg: sw1c { |
| regulator-name = "VDD_SOC (sw1abc)"; |
| regulator-min-microvolt = <1275000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-name = "VDD_ARM (sw2)"; |
| regulator-min-microvolt = <1050000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <6250>; |
| }; |
| |
| sw3a_reg: sw3a { |
| compatible = "regulator-fixed"; |
| regulator-name = "DDR_1V5a"; |
| regulator-boot-on; |
| regulator-always-on; |
| |
| }; |
| |
| sw3b_reg: sw3b { |
| compatible = "regulator-fixed"; |
| regulator-name = "DDR_1V5b"; |
| regulator-boot-on; |
| regulator-always-on; |
| |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-name = "AUX 3V15 (sw4)"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| swbst_reg: swbst { |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5150000>; |
| regulator-boot-on; |
| regulator-always-on; |
| status = "disabled"; |
| }; |
| |
| snvs_reg: vsnvs { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vref_reg: vrefddr { |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| regulator-always-on; |
| }; |
| |
| vgen2_reg: vgen2 { |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| regulator-always-on; |
| }; |
| |
| vgen3_reg: vgen3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| vgen4_reg: vgen4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vgen5_reg: vgen5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vgen6_reg: vgen6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| lm75: sensor@49 { |
| compatible = "national,lm75b"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_lm75>; |
| reg = <0x49>; |
| }; |
| |
| eeprom: eeprom@50 { |
| compatible = "atmel,24c32"; |
| reg = <0x50>; |
| pagesize = <32>; |
| }; |
| |
| rtc: rtc@51 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rtc>; |
| compatible = "nxp,pcf8563"; |
| reg = <0x51>; |
| }; |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| clock-frequency = <100000>; |
| status = "okay"; |
| |
| eeprom_ext: eeprom@50 { |
| compatible = "atmel,24c32"; |
| reg = <0x50>; |
| pagesize = <32>; |
| }; |
| }; |
| |
| &i2c3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| usb3503: usb@8 { |
| compatible = "smsc,usb3503"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb3503>; |
| reg = <0x08>; |
| connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */ |
| intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */ |
| reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */ |
| initial-mode = <1>; |
| clocks = <&refclk>; |
| clock-names = "refclk"; |
| refclk-frequency = <12000000>; |
| }; |
| |
| exc3000: touchscreen@2a { |
| compatible = "eeti,exc3000"; |
| reg = <0x2a>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ctouch>; |
| interrupt-parent = <&gpio4>; |
| interrupts = <6 IRQ_TYPE_LEVEL_LOW>; |
| touchscreen-size-x = <4096>; |
| touchscreen-size-y = <4096>; |
| }; |
| |
| vcnl4035: light-sensor@60 { |
| compatible = "vishay,vcnl4035"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_proximity>; |
| reg = <0x60>; |
| }; |
| }; |
| |
| &ldb { |
| status = "okay"; |
| |
| lvds0: lvds-channel@0 { |
| fsl,data-mapping = "spwg"; |
| fsl,data-width = <24>; |
| |
| port@4 { |
| reg = <4>; |
| |
| lvds0_out: endpoint { |
| remote-endpoint = <&panel_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| &pwm1 { |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm1>; |
| status = "okay"; |
| }; |
| |
| &pwm2 { |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm2>; |
| status = "okay"; |
| }; |
| |
| &pwm3 { |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm3>; |
| status = "okay"; |
| }; |
| |
| &pwm4 { |
| #pwm-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pwm4>; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| rts-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>; |
| linux,rs485-enabled-at-boot-time; |
| rs485-rx-during-tx; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| &usbh1 { |
| vbus-supply = <®_usb_h1_vbus>; |
| status = "okay"; |
| }; |
| |
| &usbh2 { |
| pinctrl-names = "idle", "active"; |
| pinctrl-0 = <&pinctrl_usbh2_idle>; |
| pinctrl-1 = <&pinctrl_usbh2_active>; |
| vbus-supply = <®_usb_h2_vbus>; |
| status = "okay"; |
| }; |
| |
| &usbotg { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usbotg>; |
| vbus-supply = <®_usb_otg_vbus>; |
| disable-over-current; |
| dr_mode = "otg"; |
| srp-disable; |
| hnp-disable; |
| adp-disable; |
| status = "okay"; |
| }; |
| |
| &usbphynop1 { |
| clocks = <&clks IMX6QDL_CLK_USBPHY1>; |
| clock-names = "main_clk"; |
| vcc-supply = <®_usb_h1_vbus>; |
| }; |
| |
| &usbphynop2 { |
| vcc-supply = <®_usb_h2_vbus>; |
| }; |
| |
| &usdhc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc2>; |
| cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; |
| no-1-8-v; |
| keep-power-in-suspend; |
| wakeup-source; |
| voltage-ranges = <3300 3300>; |
| vmmc-supply = <®_sw4>; |
| fsl,wp-controller; |
| status = "okay"; |
| }; |
| |
| &usdhc4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc4>; |
| bus-width = <8>; |
| non-removable; |
| no-1-8-v; |
| keep-power-in-suspend; |
| voltage-ranges = <3300 3300>; |
| vmmc-supply = <®_sw4>; |
| fsl,wp-controller; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog1>; |
| fsl,ext-reset-output; |
| timeout-sec = <10>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_enet: enetgrp { |
| fsl,pins = < |
| MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 |
| MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 |
| MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 |
| MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0 /* FEC INT */ |
| MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 |
| MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x0001b098 |
| MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 |
| MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 |
| MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x0001b098 |
| MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x0001b098 |
| MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 |
| >; |
| }; |
| |
| pinctrl_reset_gpio_led: reset-gpio-led-grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 |
| MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b810 |
| MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b810 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 |
| MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 |
| >; |
| }; |
| |
| pinctrl_lcd_enable: lcdenablegrp { |
| fsl,pins = < |
| MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 /* lcd enable */ |
| MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x1b0b0 /* sel6_8 */ |
| >; |
| }; |
| |
| pinctrl_lm75: lm75grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_proximity: proximitygrp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0 |
| >; |
| }; |
| |
| pinctrl_pwm1: pwm1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_pwm2: pwm2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_pwm3: pwm3grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_pwm4: pwm4grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_rtc: rtc-grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0 /* RTC INT */ |
| >; |
| }; |
| |
| pinctrl_ctouch: ctouch-grp { |
| fsl,pins = < |
| MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* CTOUCH_INT */ |
| MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x0001b0b0 /* CTOUCH_RESET */ |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1 |
| MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1 |
| MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1 |
| MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1 |
| >; |
| }; |
| |
| pinctrl_usbh2_idle: usbh2-idle-grp { |
| fsl,pins = < |
| MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x00013018 |
| MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00013018 |
| >; |
| }; |
| |
| pinctrl_usbh2_active: usbh2-active-grp { |
| fsl,pins = < |
| MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x00013018 |
| MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00017018 |
| >; |
| }; |
| |
| pinctrl_usb3503: usb3503-grp { |
| fsl,pins = < |
| MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x00000018 |
| MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 /* USB INT */ |
| MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x0001b0b0 /* USB Reset */ |
| MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0 /* USB Connect */ |
| >; |
| }; |
| |
| pinctrl_usbotg: usbotggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD2_CMD__SD2_CMD 0x00017069 |
| MX6QDL_PAD_SD2_CLK__SD2_CLK 0x00010038 |
| MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017069 |
| MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017069 |
| MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017069 |
| MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017069 |
| MX6QDL_PAD_GPIO_4__SD2_CD_B 0x0001b0b0 |
| >; |
| }; |
| |
| pinctrl_usdhc4: usdhc4grp { |
| fsl,pins = < |
| MX6QDL_PAD_SD4_CMD__SD4_CMD 0x00017059 |
| MX6QDL_PAD_SD4_CLK__SD4_CLK 0x00010059 |
| MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x00017059 |
| MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x00017059 |
| MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x00017059 |
| MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x00017059 |
| MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x00017059 |
| MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x00017059 |
| MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x00017059 |
| MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x00017059 |
| >; |
| }; |
| |
| pinctrl_wdog1: wdoggrp { |
| fsl,pins = < |
| MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0 |
| >; |
| }; |
| }; |
