| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| // |
| // Copyright (C) 2016-2018 Zodiac Inflight Innovations |
| |
| /dts-v1/; |
| #include "vf610.dtsi" |
| |
| / { |
| model = "ZII VF610 SCU4 AIB"; |
| compatible = "zii,vf610scu4-aib", "zii,vf610dev", "fsl,vf610"; |
| |
| chosen { |
| stdout-path = &uart0; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x20000000>; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| pinctrl-0 = <&pinctrl_leds_debug>; |
| pinctrl-names = "default"; |
| |
| led-debug { |
| label = "zii:green:debug1"; |
| gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| mdio-mux { |
| compatible = "mdio-mux-gpio"; |
| pinctrl-0 = <&pinctrl_mdio_mux>; |
| pinctrl-names = "default"; |
| gpios = <&gpio4 4 GPIO_ACTIVE_HIGH |
| &gpio4 5 GPIO_ACTIVE_HIGH |
| &gpio3 30 GPIO_ACTIVE_HIGH |
| &gpio3 31 GPIO_ACTIVE_HIGH>; |
| mdio-parent-bus = <&mdio1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| mdio_mux_1: mdio@1 { |
| reg = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch0: switch0@0 { |
| compatible = "marvell,mv88e6190"; |
| reg = <0>; |
| dsa,member = <0 0>; |
| eeprom-length = <65536>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| label = "cpu"; |
| ethernet = <&fec1>; |
| |
| fixed-link { |
| speed = <100>; |
| full-duplex; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| label = "aib2main_1"; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| label = "aib2main_2"; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "eth_cu_1000_5"; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| label = "eth_cu_1000_6"; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| label = "eth_cu_1000_4"; |
| }; |
| |
| port@6 { |
| reg = <6>; |
| label = "eth_cu_1000_7"; |
| }; |
| |
| port@7 { |
| reg = <7>; |
| label = "modem_pic"; |
| |
| fixed-link { |
| speed = <100>; |
| full-duplex; |
| }; |
| }; |
| |
| switch0port10: port@10 { |
| reg = <10>; |
| label = "dsa"; |
| phy-mode = "xgmii"; |
| link = <&switch1port10 |
| &switch3port10 |
| &switch2port10>; |
| }; |
| }; |
| }; |
| }; |
| |
| mdio_mux_2: mdio@2 { |
| reg = <2>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch1: switch1@0 { |
| compatible = "marvell,mv88e6190"; |
| reg = <0>; |
| dsa,member = <0 1>; |
| eeprom-length = <65536>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| label = "eth_cu_1000_3"; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| label = "eth_cu_100_2"; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "eth_cu_100_3"; |
| }; |
| |
| switch1port9: port@9 { |
| reg = <9>; |
| label = "dsa"; |
| phy-mode = "xgmii"; |
| link = <&switch3port10 |
| &switch2port10>; |
| }; |
| |
| switch1port10: port@10 { |
| reg = <10>; |
| label = "dsa"; |
| phy-mode = "xgmii"; |
| link = <&switch0port10>; |
| }; |
| }; |
| }; |
| }; |
| |
| mdio_mux_4: mdio@4 { |
| reg = <4>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch2: switch2@0 { |
| compatible = "marvell,mv88e6190"; |
| reg = <0>; |
| dsa,member = <0 2>; |
| eeprom-length = <65536>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@2 { |
| reg = <2>; |
| label = "eth_fc_1000_2"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff1>; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "eth_fc_1000_3"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff2>; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| label = "eth_fc_1000_4"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff3>; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| label = "eth_fc_1000_5"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff4>; |
| }; |
| |
| port@6 { |
| reg = <6>; |
| label = "eth_fc_1000_6"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff5>; |
| }; |
| |
| port@7 { |
| reg = <7>; |
| label = "eth_fc_1000_7"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff6>; |
| }; |
| |
| port@9 { |
| reg = <9>; |
| label = "eth_fc_1000_1"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff0>; |
| }; |
| |
| switch2port10: port@10 { |
| reg = <10>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| link = <&switch3port9 |
| &switch1port9 |
| &switch0port10>; |
| }; |
| }; |
| }; |
| }; |
| |
| mdio_mux_8: mdio@8 { |
| reg = <8>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| switch3: switch3@0 { |
| compatible = "marvell,mv88e6190"; |
| reg = <0>; |
| dsa,member = <0 3>; |
| eeprom-length = <65536>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@2 { |
| reg = <2>; |
| label = "eth_fc_1000_8"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff7>; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| label = "eth_fc_1000_9"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff8>; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| label = "eth_fc_1000_10"; |
| phy-mode = "1000base-x"; |
| managed = "in-band-status"; |
| sfp = <&sff9>; |
| }; |
| |
| switch3port9: port@9 { |
| reg = <9>; |
| label = "dsa"; |
| phy-mode = "2500base-x"; |
| link = <&switch2port10>; |
| }; |
| |
| switch3port10: port@10 { |
| reg = <10>; |
| label = "dsa"; |
| phy-mode = "xgmii"; |
| link = <&switch1port9 |
| &switch0port10>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| sff0: sff0 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff0_i2c>; |
| los-gpios = <&gpio9 0 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff1: sff1 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff1_i2c>; |
| los-gpios = <&gpio9 1 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff2: sff2 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff2_i2c>; |
| los-gpios = <&gpio9 2 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff3: sff3 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff3_i2c>; |
| los-gpios = <&gpio9 3 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff4: sff4 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff4_i2c>; |
| los-gpios = <&gpio9 4 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff5: sff5 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff5_i2c>; |
| los-gpios = <&gpio9 5 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 5 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff6: sff6 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff6_i2c>; |
| los-gpios = <&gpio9 6 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff7: sff7 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff7_i2c>; |
| los-gpios = <&gpio9 7 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 7 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff8: sff8 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff8_i2c>; |
| los-gpios = <&gpio9 8 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| sff9: sff9 { |
| compatible = "sff,sff"; |
| i2c-bus = <&sff9_i2c>; |
| los-gpios = <&gpio9 9 GPIO_ACTIVE_HIGH>; |
| tx-disable-gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_3v3_mcu"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| &dspi0 { |
| pinctrl-0 = <&pinctrl_dspi0>; |
| pinctrl-names = "default"; |
| bus-num = <0>; |
| status = "okay"; |
| |
| adc@5 { |
| compatible = "holt,hi8435"; |
| reg = <5>; |
| gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>; |
| spi-max-frequency = <1000000>; |
| }; |
| }; |
| |
| &dspi1 { |
| bus-num = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_dspi1>; |
| status = "okay"; |
| |
| flash@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <50000000>; |
| |
| partition@0 { |
| label = "m25p128-0"; |
| reg = <0x0 0x01000000>; |
| }; |
| }; |
| |
| flash@1 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| reg = <1>; |
| spi-max-frequency = <50000000>; |
| |
| partition@0 { |
| label = "m25p128-1"; |
| reg = <0x0 0x01000000>; |
| }; |
| }; |
| }; |
| |
| &adc0 { |
| vref-supply = <®_vcc_3v3_mcu>; |
| status = "okay"; |
| }; |
| |
| &adc1 { |
| vref-supply = <®_vcc_3v3_mcu>; |
| status = "okay"; |
| }; |
| |
| &edma0 { |
| status = "okay"; |
| }; |
| |
| &edma1 { |
| status = "okay"; |
| }; |
| |
| &esdhc0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_esdhc0>; |
| bus-width = <8>; |
| non-removable; |
| no-1-8-v; |
| no-sd; |
| no-sdio; |
| keep-power-in-suspend; |
| status = "okay"; |
| }; |
| |
| &esdhc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_esdhc1>; |
| bus-width = <4>; |
| no-sdio; |
| status = "okay"; |
| }; |
| |
| &fec1 { |
| phy-mode = "rmii"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| status = "okay"; |
| |
| fixed-link { |
| speed = <100>; |
| full-duplex; |
| }; |
| |
| mdio1: mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| &i2c0 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c0>; |
| status = "okay"; |
| |
| gpio5: io-expander@20 { |
| compatible = "nxp,pca9554"; |
| reg = <0x20>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| gpio6: io-expander@22 { |
| compatible = "nxp,pca9554"; |
| reg = <0x22>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| |
| temp-sensor@48 { |
| compatible = "national,lm75"; |
| reg = <0x48>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c04"; |
| reg = <0x50>; |
| }; |
| |
| eeprom@52 { |
| compatible = "atmel,24c04"; |
| reg = <0x52>; |
| }; |
| |
| elapsed-time-recorder@6b { |
| compatible = "dallas,ds1682"; |
| reg = <0x6b>; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| watchdog@38 { |
| compatible = "zii,rave-wdt"; |
| reg = <0x38>; |
| }; |
| |
| adc@4a { |
| compatible = "adi,adt7411"; |
| reg = <0x4a>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| |
| gpio9: io-expander@20 { |
| compatible = "semtech,sx1503q"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_sx1503_20>; |
| #gpio-cells = <2>; |
| reg = <0x20>; |
| gpio-controller; |
| interrupt-parent = <&gpio1>; |
| interrupts = <31 IRQ_TYPE_EDGE_FALLING>; |
| }; |
| |
| temp-sensor@4e { |
| compatible = "national,lm75"; |
| reg = <0x4e>; |
| }; |
| |
| temp-sensor@4f { |
| compatible = "national,lm75"; |
| reg = <0x4f>; |
| }; |
| |
| gpio7: io-expander@23 { |
| compatible = "nxp,pca9555"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| reg = <0x23>; |
| }; |
| |
| adc@4a { |
| compatible = "adi,adt7411"; |
| reg = <0x4a>; |
| }; |
| |
| eeprom@54 { |
| compatible = "atmel,24c08"; |
| reg = <0x54>; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9548"; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x70>; |
| i2c-mux-idle-disconnect; |
| |
| sff0_i2c: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| }; |
| |
| sff1_i2c: i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| }; |
| |
| sff2_i2c: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| }; |
| |
| sff3_i2c: i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| }; |
| |
| sff4_i2c: i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| }; |
| }; |
| |
| i2c-mux@71 { |
| compatible = "nxp,pca9548"; |
| pinctrl-names = "default"; |
| reg = <0x71>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| i2c-mux-idle-disconnect; |
| |
| sff5_i2c: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| }; |
| |
| sff6_i2c: i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| }; |
| |
| sff7_i2c: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| }; |
| |
| sff8_i2c: i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| }; |
| |
| sff9_i2c: i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| }; |
| }; |
| }; |
| |
| &snvsrtc { |
| status = "disabled"; |
| }; |
| |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart0>; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| linux,rs485-enabled-at-boot-time; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| linux,rs485-enabled-at-boot-time; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_dspi0: dspi0grp { |
| fsl,pins = < |
| VF610_PAD_PTB19__DSPI0_CS0 0x1182 |
| VF610_PAD_PTB18__DSPI0_CS1 0x1182 |
| VF610_PAD_PTB13__DSPI0_CS4 0x1182 |
| VF610_PAD_PTB12__DSPI0_CS5 0x1182 |
| VF610_PAD_PTB20__DSPI0_SIN 0x1181 |
| VF610_PAD_PTB21__DSPI0_SOUT 0x1182 |
| VF610_PAD_PTB22__DSPI0_SCK 0x1182 |
| >; |
| }; |
| |
| pinctrl_dspi1: dspi1grp { |
| fsl,pins = < |
| VF610_PAD_PTD5__DSPI1_CS0 0x1182 |
| VF610_PAD_PTD4__DSPI1_CS1 0x1182 |
| VF610_PAD_PTC6__DSPI1_SIN 0x1181 |
| VF610_PAD_PTC7__DSPI1_SOUT 0x1182 |
| VF610_PAD_PTC8__DSPI1_SCK 0x1182 |
| >; |
| }; |
| |
| pinctrl_dspi2: dspi2gpio { |
| fsl,pins = < |
| VF610_PAD_PTD30__GPIO_64 0x33e2 |
| VF610_PAD_PTD29__GPIO_65 0x33e1 |
| VF610_PAD_PTD28__GPIO_66 0x33e2 |
| VF610_PAD_PTD27__GPIO_67 0x33e2 |
| VF610_PAD_PTD26__GPIO_68 0x31c2 |
| >; |
| }; |
| |
| pinctrl_esdhc0: esdhc0grp { |
| fsl,pins = < |
| VF610_PAD_PTC0__ESDHC0_CLK 0x31ef |
| VF610_PAD_PTC1__ESDHC0_CMD 0x31ef |
| VF610_PAD_PTC2__ESDHC0_DAT0 0x31ef |
| VF610_PAD_PTC3__ESDHC0_DAT1 0x31ef |
| VF610_PAD_PTC4__ESDHC0_DAT2 0x31ef |
| VF610_PAD_PTC5__ESDHC0_DAT3 0x31ef |
| VF610_PAD_PTD23__ESDHC0_DAT4 0x31ef |
| VF610_PAD_PTD22__ESDHC0_DAT5 0x31ef |
| VF610_PAD_PTD21__ESDHC0_DAT6 0x31ef |
| VF610_PAD_PTD20__ESDHC0_DAT7 0x31ef |
| >; |
| }; |
| |
| pinctrl_esdhc1: esdhc1grp { |
| fsl,pins = < |
| VF610_PAD_PTA24__ESDHC1_CLK 0x31ef |
| VF610_PAD_PTA25__ESDHC1_CMD 0x31ef |
| VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef |
| VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef |
| VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef |
| VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| VF610_PAD_PTA6__RMII_CLKIN 0x30d1 |
| VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 |
| VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 |
| VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 |
| VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1 |
| VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 |
| VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 |
| VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 |
| VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 |
| VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 |
| >; |
| }; |
| |
| pinctrl_i2c0: i2c0grp { |
| fsl,pins = < |
| VF610_PAD_PTB14__I2C0_SCL 0x37ff |
| VF610_PAD_PTB15__I2C0_SDA 0x37ff |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| VF610_PAD_PTB16__I2C1_SCL 0x37ff |
| VF610_PAD_PTB17__I2C1_SDA 0x37ff |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| VF610_PAD_PTA22__I2C2_SCL 0x37ff |
| VF610_PAD_PTA23__I2C2_SDA 0x37ff |
| >; |
| }; |
| |
| pinctrl_leds_debug: pinctrl-leds-debug { |
| fsl,pins = < |
| VF610_PAD_PTB26__GPIO_96 0x31c2 |
| >; |
| }; |
| |
| pinctrl_mdio_mux: pinctrl-mdio-mux { |
| fsl,pins = < |
| VF610_PAD_PTE27__GPIO_132 0x31c2 |
| VF610_PAD_PTE28__GPIO_133 0x31c2 |
| VF610_PAD_PTE21__GPIO_126 0x31c2 |
| VF610_PAD_PTE22__GPIO_127 0x31c2 |
| >; |
| }; |
| |
| pinctrl_qspi0: qspi0grp { |
| fsl,pins = < |
| VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3 |
| VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff |
| VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3 |
| VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3 |
| VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3 |
| VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3 |
| >; |
| }; |
| |
| pinctrl_sx1503_20: pinctrl-sx1503-20 { |
| fsl,pins = < |
| VF610_PAD_PTD31__GPIO_63 0x219d |
| >; |
| }; |
| |
| pinctrl_uart0: uart0grp { |
| fsl,pins = < |
| VF610_PAD_PTB10__UART0_TX 0x21a2 |
| VF610_PAD_PTB11__UART0_RX 0x21a1 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| VF610_PAD_PTB23__UART1_TX 0x21a2 |
| VF610_PAD_PTB24__UART1_RX 0x21a1 |
| VF610_PAD_PTB25__UART1_RTS 0x21a2 /* Used as DE signal for the RS-485 transceiver */ |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| VF610_PAD_PTD0__UART2_TX 0x21a2 |
| VF610_PAD_PTD1__UART2_RX 0x21a1 |
| VF610_PAD_PTD2__UART2_RTS 0x21a2 /* Used as DE signal for the RS-485 transceiver */ |
| >; |
| }; |
| }; |
