| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2022 Analog Devices, Inc. |
| * Author: Cosmin Tanislav <cosmin.tanislav@analog.com> |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/bitops.h> |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/err.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/property.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/spi/spi.h> |
| #include <linux/units.h> |
| |
| #include <asm/div64.h> |
| #include <asm/unaligned.h> |
| |
| #include <linux/iio/buffer.h> |
| #include <linux/iio/iio.h> |
| #include <linux/iio/kfifo_buf.h> |
| #include <linux/iio/sysfs.h> |
| |
| #define AD4130_NAME "ad4130" |
| |
| #define AD4130_COMMS_READ_MASK BIT(6) |
| |
| #define AD4130_STATUS_REG 0x00 |
| |
| #define AD4130_ADC_CONTROL_REG 0x01 |
| #define AD4130_ADC_CONTROL_BIPOLAR_MASK BIT(14) |
| #define AD4130_ADC_CONTROL_INT_REF_VAL_MASK BIT(13) |
| #define AD4130_INT_REF_2_5V 2500000 |
| #define AD4130_INT_REF_1_25V 1250000 |
| #define AD4130_ADC_CONTROL_CSB_EN_MASK BIT(9) |
| #define AD4130_ADC_CONTROL_INT_REF_EN_MASK BIT(8) |
| #define AD4130_ADC_CONTROL_MODE_MASK GENMASK(5, 2) |
| #define AD4130_ADC_CONTROL_MCLK_SEL_MASK GENMASK(1, 0) |
| #define AD4130_MCLK_FREQ_76_8KHZ 76800 |
| #define AD4130_MCLK_FREQ_153_6KHZ 153600 |
| |
| #define AD4130_DATA_REG 0x02 |
| |
| #define AD4130_IO_CONTROL_REG 0x03 |
| #define AD4130_IO_CONTROL_INT_PIN_SEL_MASK GENMASK(9, 8) |
| #define AD4130_IO_CONTROL_GPIO_DATA_MASK GENMASK(7, 4) |
| #define AD4130_IO_CONTROL_GPIO_CTRL_MASK GENMASK(3, 0) |
| |
| #define AD4130_VBIAS_REG 0x04 |
| |
| #define AD4130_ID_REG 0x05 |
| |
| #define AD4130_ERROR_REG 0x06 |
| |
| #define AD4130_ERROR_EN_REG 0x07 |
| |
| #define AD4130_MCLK_COUNT_REG 0x08 |
| |
| #define AD4130_CHANNEL_X_REG(x) (0x09 + (x)) |
| #define AD4130_CHANNEL_EN_MASK BIT(23) |
| #define AD4130_CHANNEL_SETUP_MASK GENMASK(22, 20) |
| #define AD4130_CHANNEL_AINP_MASK GENMASK(17, 13) |
| #define AD4130_CHANNEL_AINM_MASK GENMASK(12, 8) |
| #define AD4130_CHANNEL_IOUT1_MASK GENMASK(7, 4) |
| #define AD4130_CHANNEL_IOUT2_MASK GENMASK(3, 0) |
| |
| #define AD4130_CONFIG_X_REG(x) (0x19 + (x)) |
| #define AD4130_CONFIG_IOUT1_VAL_MASK GENMASK(15, 13) |
| #define AD4130_CONFIG_IOUT2_VAL_MASK GENMASK(12, 10) |
| #define AD4130_CONFIG_BURNOUT_MASK GENMASK(9, 8) |
| #define AD4130_CONFIG_REF_BUFP_MASK BIT(7) |
| #define AD4130_CONFIG_REF_BUFM_MASK BIT(6) |
| #define AD4130_CONFIG_REF_SEL_MASK GENMASK(5, 4) |
| #define AD4130_CONFIG_PGA_MASK GENMASK(3, 1) |
| |
| #define AD4130_FILTER_X_REG(x) (0x21 + (x)) |
| #define AD4130_FILTER_MODE_MASK GENMASK(15, 12) |
| #define AD4130_FILTER_SELECT_MASK GENMASK(10, 0) |
| #define AD4130_FILTER_SELECT_MIN 1 |
| |
| #define AD4130_OFFSET_X_REG(x) (0x29 + (x)) |
| |
| #define AD4130_GAIN_X_REG(x) (0x31 + (x)) |
| |
| #define AD4130_MISC_REG 0x39 |
| |
| #define AD4130_FIFO_CONTROL_REG 0x3a |
| #define AD4130_FIFO_CONTROL_HEADER_MASK BIT(18) |
| #define AD4130_FIFO_CONTROL_MODE_MASK GENMASK(17, 16) |
| #define AD4130_FIFO_CONTROL_WM_INT_EN_MASK BIT(9) |
| #define AD4130_FIFO_CONTROL_WM_MASK GENMASK(7, 0) |
| #define AD4130_WATERMARK_256 0 |
| |
| #define AD4130_FIFO_STATUS_REG 0x3b |
| |
| #define AD4130_FIFO_THRESHOLD_REG 0x3c |
| |
| #define AD4130_FIFO_DATA_REG 0x3d |
| #define AD4130_FIFO_SIZE 256 |
| #define AD4130_FIFO_MAX_SAMPLE_SIZE 3 |
| |
| #define AD4130_MAX_ANALOG_PINS 16 |
| #define AD4130_MAX_CHANNELS 16 |
| #define AD4130_MAX_DIFF_INPUTS 30 |
| #define AD4130_MAX_GPIOS 4 |
| #define AD4130_MAX_ODR 2400 |
| #define AD4130_MAX_PGA 8 |
| #define AD4130_MAX_SETUPS 8 |
| |
| #define AD4130_AIN2_P1 0x2 |
| #define AD4130_AIN3_P2 0x3 |
| |
| #define AD4130_RESET_BUF_SIZE 8 |
| #define AD4130_RESET_SLEEP_US (160 * MICRO / AD4130_MCLK_FREQ_76_8KHZ) |
| |
| #define AD4130_INVALID_SLOT -1 |
| |
| static const unsigned int ad4130_reg_size[] = { |
| [AD4130_STATUS_REG] = 1, |
| [AD4130_ADC_CONTROL_REG] = 2, |
| [AD4130_DATA_REG] = 3, |
| [AD4130_IO_CONTROL_REG] = 2, |
| [AD4130_VBIAS_REG] = 2, |
| [AD4130_ID_REG] = 1, |
| [AD4130_ERROR_REG] = 2, |
| [AD4130_ERROR_EN_REG] = 2, |
| [AD4130_MCLK_COUNT_REG] = 1, |
| [AD4130_CHANNEL_X_REG(0) ... AD4130_CHANNEL_X_REG(AD4130_MAX_CHANNELS - 1)] = 3, |
| [AD4130_CONFIG_X_REG(0) ... AD4130_CONFIG_X_REG(AD4130_MAX_SETUPS - 1)] = 2, |
| [AD4130_FILTER_X_REG(0) ... AD4130_FILTER_X_REG(AD4130_MAX_SETUPS - 1)] = 3, |
| [AD4130_OFFSET_X_REG(0) ... AD4130_OFFSET_X_REG(AD4130_MAX_SETUPS - 1)] = 3, |
| [AD4130_GAIN_X_REG(0) ... AD4130_GAIN_X_REG(AD4130_MAX_SETUPS - 1)] = 3, |
| [AD4130_MISC_REG] = 2, |
| [AD4130_FIFO_CONTROL_REG] = 3, |
| [AD4130_FIFO_STATUS_REG] = 1, |
| [AD4130_FIFO_THRESHOLD_REG] = 3, |
| [AD4130_FIFO_DATA_REG] = 3, |
| }; |
| |
| enum ad4130_int_ref_val { |
| AD4130_INT_REF_VAL_2_5V, |
| AD4130_INT_REF_VAL_1_25V, |
| }; |
| |
| enum ad4130_mclk_sel { |
| AD4130_MCLK_76_8KHZ, |
| AD4130_MCLK_76_8KHZ_OUT, |
| AD4130_MCLK_76_8KHZ_EXT, |
| AD4130_MCLK_153_6KHZ_EXT, |
| }; |
| |
| enum ad4130_int_pin_sel { |
| AD4130_INT_PIN_INT, |
| AD4130_INT_PIN_CLK, |
| AD4130_INT_PIN_P2, |
| AD4130_INT_PIN_DOUT, |
| }; |
| |
| enum ad4130_iout { |
| AD4130_IOUT_OFF, |
| AD4130_IOUT_10000NA, |
| AD4130_IOUT_20000NA, |
| AD4130_IOUT_50000NA, |
| AD4130_IOUT_100000NA, |
| AD4130_IOUT_150000NA, |
| AD4130_IOUT_200000NA, |
| AD4130_IOUT_100NA, |
| AD4130_IOUT_MAX |
| }; |
| |
| enum ad4130_burnout { |
| AD4130_BURNOUT_OFF, |
| AD4130_BURNOUT_500NA, |
| AD4130_BURNOUT_2000NA, |
| AD4130_BURNOUT_4000NA, |
| AD4130_BURNOUT_MAX |
| }; |
| |
| enum ad4130_ref_sel { |
| AD4130_REF_REFIN1, |
| AD4130_REF_REFIN2, |
| AD4130_REF_REFOUT_AVSS, |
| AD4130_REF_AVDD_AVSS, |
| AD4130_REF_SEL_MAX |
| }; |
| |
| enum ad4130_fifo_mode { |
| AD4130_FIFO_MODE_DISABLED = 0b00, |
| AD4130_FIFO_MODE_WM = 0b01, |
| }; |
| |
| enum ad4130_mode { |
| AD4130_MODE_CONTINUOUS = 0b0000, |
| AD4130_MODE_IDLE = 0b0100, |
| }; |
| |
| enum ad4130_filter_mode { |
| AD4130_FILTER_SINC4, |
| AD4130_FILTER_SINC4_SINC1, |
| AD4130_FILTER_SINC3, |
| AD4130_FILTER_SINC3_REJ60, |
| AD4130_FILTER_SINC3_SINC1, |
| AD4130_FILTER_SINC3_PF1, |
| AD4130_FILTER_SINC3_PF2, |
| AD4130_FILTER_SINC3_PF3, |
| AD4130_FILTER_SINC3_PF4, |
| }; |
| |
| enum ad4130_pin_function { |
| AD4130_PIN_FN_NONE, |
| AD4130_PIN_FN_SPECIAL = BIT(0), |
| AD4130_PIN_FN_DIFF = BIT(1), |
| AD4130_PIN_FN_EXCITATION = BIT(2), |
| AD4130_PIN_FN_VBIAS = BIT(3), |
| }; |
| |
| struct ad4130_setup_info { |
| unsigned int iout0_val; |
| unsigned int iout1_val; |
| unsigned int burnout; |
| unsigned int pga; |
| unsigned int fs; |
| u32 ref_sel; |
| enum ad4130_filter_mode filter_mode; |
| bool ref_bufp; |
| bool ref_bufm; |
| }; |
| |
| struct ad4130_slot_info { |
| struct ad4130_setup_info setup; |
| unsigned int enabled_channels; |
| unsigned int channels; |
| }; |
| |
| struct ad4130_chan_info { |
| struct ad4130_setup_info setup; |
| u32 iout0; |
| u32 iout1; |
| int slot; |
| bool enabled; |
| bool initialized; |
| }; |
| |
| struct ad4130_filter_config { |
| enum ad4130_filter_mode filter_mode; |
| unsigned int odr_div; |
| unsigned int fs_max; |
| enum iio_available_type samp_freq_avail_type; |
| int samp_freq_avail_len; |
| int samp_freq_avail[3][2]; |
| }; |
| |
| struct ad4130_state { |
| struct regmap *regmap; |
| struct spi_device *spi; |
| struct clk *mclk; |
| struct regulator_bulk_data regulators[4]; |
| u32 irq_trigger; |
| u32 inv_irq_trigger; |
| |
| /* |
| * Synchronize access to members the of driver state, and ensure |
| * atomicity of consecutive regmap operations. |
| */ |
| struct mutex lock; |
| struct completion completion; |
| |
| struct iio_chan_spec chans[AD4130_MAX_CHANNELS]; |
| struct ad4130_chan_info chans_info[AD4130_MAX_CHANNELS]; |
| struct ad4130_slot_info slots_info[AD4130_MAX_SETUPS]; |
| enum ad4130_pin_function pins_fn[AD4130_MAX_ANALOG_PINS]; |
| u32 vbias_pins[AD4130_MAX_ANALOG_PINS]; |
| u32 num_vbias_pins; |
| int scale_tbls[AD4130_REF_SEL_MAX][AD4130_MAX_PGA][2]; |
| struct gpio_chip gc; |
| struct clk_hw int_clk_hw; |
| |
| u32 int_pin_sel; |
| u32 int_ref_uv; |
| u32 mclk_sel; |
| bool int_ref_en; |
| bool bipolar; |
| |
| unsigned int num_enabled_channels; |
| unsigned int effective_watermark; |
| unsigned int watermark; |
| |
| struct spi_message fifo_msg; |
| struct spi_transfer fifo_xfer[2]; |
| |
| /* |
| * DMA (thus cache coherency maintenance) requires any transfer |
| * buffers to live in their own cache lines. As the use of these |
| * buffers is synchronous, all of the buffers used for DMA in this |
| * driver may share a cache line. |
| */ |
| u8 reset_buf[AD4130_RESET_BUF_SIZE] __aligned(IIO_DMA_MINALIGN); |
| u8 reg_write_tx_buf[4]; |
| u8 reg_read_tx_buf[1]; |
| u8 reg_read_rx_buf[3]; |
| u8 fifo_tx_buf[2]; |
| u8 fifo_rx_buf[AD4130_FIFO_SIZE * |
| AD4130_FIFO_MAX_SAMPLE_SIZE]; |
| }; |
| |
| static const char * const ad4130_int_pin_names[] = { |
| [AD4130_INT_PIN_INT] = "int", |
| [AD4130_INT_PIN_CLK] = "clk", |
| [AD4130_INT_PIN_P2] = "p2", |
| [AD4130_INT_PIN_DOUT] = "dout", |
| }; |
| |
| static const unsigned int ad4130_iout_current_na_tbl[AD4130_IOUT_MAX] = { |
| [AD4130_IOUT_OFF] = 0, |
| [AD4130_IOUT_100NA] = 100, |
| [AD4130_IOUT_10000NA] = 10000, |
| [AD4130_IOUT_20000NA] = 20000, |
| [AD4130_IOUT_50000NA] = 50000, |
| [AD4130_IOUT_100000NA] = 100000, |
| [AD4130_IOUT_150000NA] = 150000, |
| [AD4130_IOUT_200000NA] = 200000, |
| }; |
| |
| static const unsigned int ad4130_burnout_current_na_tbl[AD4130_BURNOUT_MAX] = { |
| [AD4130_BURNOUT_OFF] = 0, |
| [AD4130_BURNOUT_500NA] = 500, |
| [AD4130_BURNOUT_2000NA] = 2000, |
| [AD4130_BURNOUT_4000NA] = 4000, |
| }; |
| |
| #define AD4130_VARIABLE_ODR_CONFIG(_filter_mode, _odr_div, _fs_max) \ |
| { \ |
| .filter_mode = (_filter_mode), \ |
| .odr_div = (_odr_div), \ |
| .fs_max = (_fs_max), \ |
| .samp_freq_avail_type = IIO_AVAIL_RANGE, \ |
| .samp_freq_avail = { \ |
| { AD4130_MAX_ODR, (_odr_div) * (_fs_max) }, \ |
| { AD4130_MAX_ODR, (_odr_div) * (_fs_max) }, \ |
| { AD4130_MAX_ODR, (_odr_div) }, \ |
| }, \ |
| } |
| |
| #define AD4130_FIXED_ODR_CONFIG(_filter_mode, _odr_div) \ |
| { \ |
| .filter_mode = (_filter_mode), \ |
| .odr_div = (_odr_div), \ |
| .fs_max = AD4130_FILTER_SELECT_MIN, \ |
| .samp_freq_avail_type = IIO_AVAIL_LIST, \ |
| .samp_freq_avail_len = 1, \ |
| .samp_freq_avail = { \ |
| { AD4130_MAX_ODR, (_odr_div) }, \ |
| }, \ |
| } |
| |
| static const struct ad4130_filter_config ad4130_filter_configs[] = { |
| AD4130_VARIABLE_ODR_CONFIG(AD4130_FILTER_SINC4, 1, 10), |
| AD4130_VARIABLE_ODR_CONFIG(AD4130_FILTER_SINC4_SINC1, 11, 10), |
| AD4130_VARIABLE_ODR_CONFIG(AD4130_FILTER_SINC3, 1, 2047), |
| AD4130_VARIABLE_ODR_CONFIG(AD4130_FILTER_SINC3_REJ60, 1, 2047), |
| AD4130_VARIABLE_ODR_CONFIG(AD4130_FILTER_SINC3_SINC1, 10, 2047), |
| AD4130_FIXED_ODR_CONFIG(AD4130_FILTER_SINC3_PF1, 92), |
| AD4130_FIXED_ODR_CONFIG(AD4130_FILTER_SINC3_PF2, 100), |
| AD4130_FIXED_ODR_CONFIG(AD4130_FILTER_SINC3_PF3, 124), |
| AD4130_FIXED_ODR_CONFIG(AD4130_FILTER_SINC3_PF4, 148), |
| }; |
| |
| static const char * const ad4130_filter_modes_str[] = { |
| [AD4130_FILTER_SINC4] = "sinc4", |
| [AD4130_FILTER_SINC4_SINC1] = "sinc4+sinc1", |
| [AD4130_FILTER_SINC3] = "sinc3", |
| [AD4130_FILTER_SINC3_REJ60] = "sinc3+rej60", |
| [AD4130_FILTER_SINC3_SINC1] = "sinc3+sinc1", |
| [AD4130_FILTER_SINC3_PF1] = "sinc3+pf1", |
| [AD4130_FILTER_SINC3_PF2] = "sinc3+pf2", |
| [AD4130_FILTER_SINC3_PF3] = "sinc3+pf3", |
| [AD4130_FILTER_SINC3_PF4] = "sinc3+pf4", |
| }; |
| |
| static int ad4130_get_reg_size(struct ad4130_state *st, unsigned int reg, |
| unsigned int *size) |
| { |
| if (reg >= ARRAY_SIZE(ad4130_reg_size)) |
| return -EINVAL; |
| |
| *size = ad4130_reg_size[reg]; |
| |
| return 0; |
| } |
| |
| static unsigned int ad4130_data_reg_size(struct ad4130_state *st) |
| { |
| unsigned int data_reg_size; |
| int ret; |
| |
| ret = ad4130_get_reg_size(st, AD4130_DATA_REG, &data_reg_size); |
| if (ret) |
| return 0; |
| |
| return data_reg_size; |
| } |
| |
| static unsigned int ad4130_resolution(struct ad4130_state *st) |
| { |
| return ad4130_data_reg_size(st) * BITS_PER_BYTE; |
| } |
| |
| static int ad4130_reg_write(void *context, unsigned int reg, unsigned int val) |
| { |
| struct ad4130_state *st = context; |
| unsigned int size; |
| int ret; |
| |
| ret = ad4130_get_reg_size(st, reg, &size); |
| if (ret) |
| return ret; |
| |
| st->reg_write_tx_buf[0] = reg; |
| |
| switch (size) { |
| case 3: |
| put_unaligned_be24(val, &st->reg_write_tx_buf[1]); |
| break; |
| case 2: |
| put_unaligned_be16(val, &st->reg_write_tx_buf[1]); |
| break; |
| case 1: |
| st->reg_write_tx_buf[1] = val; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return spi_write(st->spi, st->reg_write_tx_buf, size + 1); |
| } |
| |
| static int ad4130_reg_read(void *context, unsigned int reg, unsigned int *val) |
| { |
| struct ad4130_state *st = context; |
| struct spi_transfer t[] = { |
| { |
| .tx_buf = st->reg_read_tx_buf, |
| .len = sizeof(st->reg_read_tx_buf), |
| }, |
| { |
| .rx_buf = st->reg_read_rx_buf, |
| }, |
| }; |
| unsigned int size; |
| int ret; |
| |
| ret = ad4130_get_reg_size(st, reg, &size); |
| if (ret) |
| return ret; |
| |
| st->reg_read_tx_buf[0] = AD4130_COMMS_READ_MASK | reg; |
| t[1].len = size; |
| |
| ret = spi_sync_transfer(st->spi, t, ARRAY_SIZE(t)); |
| if (ret) |
| return ret; |
| |
| switch (size) { |
| case 3: |
| *val = get_unaligned_be24(st->reg_read_rx_buf); |
| break; |
| case 2: |
| *val = get_unaligned_be16(st->reg_read_rx_buf); |
| break; |
| case 1: |
| *val = st->reg_read_rx_buf[0]; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static const struct regmap_config ad4130_regmap_config = { |
| .reg_read = ad4130_reg_read, |
| .reg_write = ad4130_reg_write, |
| }; |
| |
| static int ad4130_gpio_init_valid_mask(struct gpio_chip *gc, |
| unsigned long *valid_mask, |
| unsigned int ngpios) |
| { |
| struct ad4130_state *st = gpiochip_get_data(gc); |
| unsigned int i; |
| |
| /* |
| * Output-only GPIO functionality is available on pins AIN2 through |
| * AIN5. If these pins are used for anything else, do not expose them. |
| */ |
| for (i = 0; i < ngpios; i++) { |
| unsigned int pin = i + AD4130_AIN2_P1; |
| bool valid = st->pins_fn[pin] == AD4130_PIN_FN_NONE; |
| |
| __assign_bit(i, valid_mask, valid); |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_gpio_get_direction(struct gpio_chip *gc, unsigned int offset) |
| { |
| return GPIO_LINE_DIRECTION_OUT; |
| } |
| |
| static void ad4130_gpio_set(struct gpio_chip *gc, unsigned int offset, |
| int value) |
| { |
| struct ad4130_state *st = gpiochip_get_data(gc); |
| unsigned int mask = FIELD_PREP(AD4130_IO_CONTROL_GPIO_DATA_MASK, |
| BIT(offset)); |
| |
| regmap_update_bits(st->regmap, AD4130_IO_CONTROL_REG, mask, |
| value ? mask : 0); |
| } |
| |
| static int ad4130_set_mode(struct ad4130_state *st, enum ad4130_mode mode) |
| { |
| return regmap_update_bits(st->regmap, AD4130_ADC_CONTROL_REG, |
| AD4130_ADC_CONTROL_MODE_MASK, |
| FIELD_PREP(AD4130_ADC_CONTROL_MODE_MASK, mode)); |
| } |
| |
| static int ad4130_set_watermark_interrupt_en(struct ad4130_state *st, bool en) |
| { |
| return regmap_update_bits(st->regmap, AD4130_FIFO_CONTROL_REG, |
| AD4130_FIFO_CONTROL_WM_INT_EN_MASK, |
| FIELD_PREP(AD4130_FIFO_CONTROL_WM_INT_EN_MASK, en)); |
| } |
| |
| static unsigned int ad4130_watermark_reg_val(unsigned int val) |
| { |
| if (val == AD4130_FIFO_SIZE) |
| val = AD4130_WATERMARK_256; |
| |
| return val; |
| } |
| |
| static int ad4130_set_fifo_mode(struct ad4130_state *st, |
| enum ad4130_fifo_mode mode) |
| { |
| return regmap_update_bits(st->regmap, AD4130_FIFO_CONTROL_REG, |
| AD4130_FIFO_CONTROL_MODE_MASK, |
| FIELD_PREP(AD4130_FIFO_CONTROL_MODE_MASK, mode)); |
| } |
| |
| static void ad4130_push_fifo_data(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int data_reg_size = ad4130_data_reg_size(st); |
| unsigned int transfer_len = st->effective_watermark * data_reg_size; |
| unsigned int set_size = st->num_enabled_channels * data_reg_size; |
| unsigned int i; |
| int ret; |
| |
| st->fifo_tx_buf[1] = ad4130_watermark_reg_val(st->effective_watermark); |
| st->fifo_xfer[1].len = transfer_len; |
| |
| ret = spi_sync(st->spi, &st->fifo_msg); |
| if (ret) |
| return; |
| |
| for (i = 0; i < transfer_len; i += set_size) |
| iio_push_to_buffers(indio_dev, &st->fifo_rx_buf[i]); |
| } |
| |
| static irqreturn_t ad4130_irq_handler(int irq, void *private) |
| { |
| struct iio_dev *indio_dev = private; |
| struct ad4130_state *st = iio_priv(indio_dev); |
| |
| if (iio_buffer_enabled(indio_dev)) |
| ad4130_push_fifo_data(indio_dev); |
| else |
| complete(&st->completion); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int ad4130_find_slot(struct ad4130_state *st, |
| struct ad4130_setup_info *target_setup_info, |
| unsigned int *slot, bool *overwrite) |
| { |
| unsigned int i; |
| |
| *slot = AD4130_INVALID_SLOT; |
| *overwrite = false; |
| |
| for (i = 0; i < AD4130_MAX_SETUPS; i++) { |
| struct ad4130_slot_info *slot_info = &st->slots_info[i]; |
| |
| /* Immediately accept a matching setup info. */ |
| if (!memcmp(target_setup_info, &slot_info->setup, |
| sizeof(*target_setup_info))) { |
| *slot = i; |
| return 0; |
| } |
| |
| /* Ignore all setups which are used by enabled channels. */ |
| if (slot_info->enabled_channels) |
| continue; |
| |
| /* Find the least used slot. */ |
| if (*slot == AD4130_INVALID_SLOT || |
| slot_info->channels < st->slots_info[*slot].channels) |
| *slot = i; |
| } |
| |
| if (*slot == AD4130_INVALID_SLOT) |
| return -EINVAL; |
| |
| *overwrite = true; |
| |
| return 0; |
| } |
| |
| static void ad4130_unlink_channel(struct ad4130_state *st, unsigned int channel) |
| { |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_slot_info *slot_info = &st->slots_info[chan_info->slot]; |
| |
| chan_info->slot = AD4130_INVALID_SLOT; |
| slot_info->channels--; |
| } |
| |
| static int ad4130_unlink_slot(struct ad4130_state *st, unsigned int slot) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < AD4130_MAX_CHANNELS; i++) { |
| struct ad4130_chan_info *chan_info = &st->chans_info[i]; |
| |
| if (!chan_info->initialized || chan_info->slot != slot) |
| continue; |
| |
| ad4130_unlink_channel(st, i); |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_link_channel_slot(struct ad4130_state *st, |
| unsigned int channel, unsigned int slot) |
| { |
| struct ad4130_slot_info *slot_info = &st->slots_info[slot]; |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| int ret; |
| |
| ret = regmap_update_bits(st->regmap, AD4130_CHANNEL_X_REG(channel), |
| AD4130_CHANNEL_SETUP_MASK, |
| FIELD_PREP(AD4130_CHANNEL_SETUP_MASK, slot)); |
| if (ret) |
| return ret; |
| |
| chan_info->slot = slot; |
| slot_info->channels++; |
| |
| return 0; |
| } |
| |
| static int ad4130_write_slot_setup(struct ad4130_state *st, |
| unsigned int slot, |
| struct ad4130_setup_info *setup_info) |
| { |
| unsigned int val; |
| int ret; |
| |
| val = FIELD_PREP(AD4130_CONFIG_IOUT1_VAL_MASK, setup_info->iout0_val) | |
| FIELD_PREP(AD4130_CONFIG_IOUT1_VAL_MASK, setup_info->iout1_val) | |
| FIELD_PREP(AD4130_CONFIG_BURNOUT_MASK, setup_info->burnout) | |
| FIELD_PREP(AD4130_CONFIG_REF_BUFP_MASK, setup_info->ref_bufp) | |
| FIELD_PREP(AD4130_CONFIG_REF_BUFM_MASK, setup_info->ref_bufm) | |
| FIELD_PREP(AD4130_CONFIG_REF_SEL_MASK, setup_info->ref_sel) | |
| FIELD_PREP(AD4130_CONFIG_PGA_MASK, setup_info->pga); |
| |
| ret = regmap_write(st->regmap, AD4130_CONFIG_X_REG(slot), val); |
| if (ret) |
| return ret; |
| |
| val = FIELD_PREP(AD4130_FILTER_MODE_MASK, setup_info->filter_mode) | |
| FIELD_PREP(AD4130_FILTER_SELECT_MASK, setup_info->fs); |
| |
| ret = regmap_write(st->regmap, AD4130_FILTER_X_REG(slot), val); |
| if (ret) |
| return ret; |
| |
| memcpy(&st->slots_info[slot].setup, setup_info, sizeof(*setup_info)); |
| |
| return 0; |
| } |
| |
| static int ad4130_write_channel_setup(struct ad4130_state *st, |
| unsigned int channel, bool on_enable) |
| { |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_setup_info *setup_info = &chan_info->setup; |
| bool overwrite; |
| int slot; |
| int ret; |
| |
| /* |
| * The following cases need to be handled. |
| * |
| * 1. Enabled and linked channel with setup changes: |
| * - Find a slot. If not possible, return error. |
| * - Unlink channel from current slot. |
| * - If the slot has channels linked to it, unlink all channels, and |
| * write the new setup to it. |
| * - Link channel to new slot. |
| * |
| * 2. Soon to be enabled and unlinked channel: |
| * - Find a slot. If not possible, return error. |
| * - If the slot has channels linked to it, unlink all channels, and |
| * write the new setup to it. |
| * - Link channel to the slot. |
| * |
| * 3. Disabled and linked channel with setup changes: |
| * - Unlink channel from current slot. |
| * |
| * 4. Soon to be enabled and linked channel: |
| * 5. Disabled and unlinked channel with setup changes: |
| * - Do nothing. |
| */ |
| |
| /* Case 4 */ |
| if (on_enable && chan_info->slot != AD4130_INVALID_SLOT) |
| return 0; |
| |
| if (!on_enable && !chan_info->enabled) { |
| if (chan_info->slot != AD4130_INVALID_SLOT) |
| /* Case 3 */ |
| ad4130_unlink_channel(st, channel); |
| |
| /* Cases 3 & 5 */ |
| return 0; |
| } |
| |
| /* Cases 1 & 2 */ |
| ret = ad4130_find_slot(st, setup_info, &slot, &overwrite); |
| if (ret) |
| return ret; |
| |
| if (chan_info->slot != AD4130_INVALID_SLOT) |
| /* Case 1 */ |
| ad4130_unlink_channel(st, channel); |
| |
| if (overwrite) { |
| ret = ad4130_unlink_slot(st, slot); |
| if (ret) |
| return ret; |
| |
| ret = ad4130_write_slot_setup(st, slot, setup_info); |
| if (ret) |
| return ret; |
| } |
| |
| return ad4130_link_channel_slot(st, channel, slot); |
| } |
| |
| static int ad4130_set_channel_enable(struct ad4130_state *st, |
| unsigned int channel, bool status) |
| { |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_slot_info *slot_info; |
| int ret; |
| |
| if (chan_info->enabled == status) |
| return 0; |
| |
| if (status) { |
| ret = ad4130_write_channel_setup(st, channel, true); |
| if (ret) |
| return ret; |
| } |
| |
| slot_info = &st->slots_info[chan_info->slot]; |
| |
| ret = regmap_update_bits(st->regmap, AD4130_CHANNEL_X_REG(channel), |
| AD4130_CHANNEL_EN_MASK, |
| FIELD_PREP(AD4130_CHANNEL_EN_MASK, status)); |
| if (ret) |
| return ret; |
| |
| slot_info->enabled_channels += status ? 1 : -1; |
| chan_info->enabled = status; |
| |
| return 0; |
| } |
| |
| /* |
| * Table 58. FILTER_MODE_n bits and Filter Types of the datasheet describes |
| * the relation between filter mode, ODR and FS. |
| * |
| * Notice that the max ODR of each filter mode is not necessarily the |
| * absolute max ODR supported by the chip. |
| * |
| * The ODR divider is not explicitly specified, but it can be deduced based |
| * on the ODR range of each filter mode. |
| * |
| * For example, for Sinc4+Sinc1, max ODR is 218.18. That means that the |
| * absolute max ODR is divided by 11 to achieve the max ODR of this filter |
| * mode. |
| * |
| * The formulas for converting between ODR and FS for a specific filter |
| * mode can be deduced from the same table. |
| * |
| * Notice that FS = 1 actually means max ODR, and that ODR decreases by |
| * (maximum ODR / maximum FS) for each increment of FS. |
| * |
| * odr = MAX_ODR / odr_div * (1 - (fs - 1) / fs_max) <=> |
| * odr = MAX_ODR * (1 - (fs - 1) / fs_max) / odr_div <=> |
| * odr = MAX_ODR * (1 - (fs - 1) / fs_max) / odr_div <=> |
| * odr = MAX_ODR * (fs_max - fs + 1) / (fs_max * odr_div) |
| * (used in ad4130_fs_to_freq) |
| * |
| * For the opposite formula, FS can be extracted from the last one. |
| * |
| * MAX_ODR * (fs_max - fs + 1) = fs_max * odr_div * odr <=> |
| * fs_max - fs + 1 = fs_max * odr_div * odr / MAX_ODR <=> |
| * fs = 1 + fs_max - fs_max * odr_div * odr / MAX_ODR |
| * (used in ad4130_fs_to_freq) |
| */ |
| |
| static void ad4130_freq_to_fs(enum ad4130_filter_mode filter_mode, |
| int val, int val2, unsigned int *fs) |
| { |
| const struct ad4130_filter_config *filter_config = |
| &ad4130_filter_configs[filter_mode]; |
| u64 dividend, divisor; |
| int temp; |
| |
| dividend = filter_config->fs_max * filter_config->odr_div * |
| ((u64)val * NANO + val2); |
| divisor = (u64)AD4130_MAX_ODR * NANO; |
| |
| temp = AD4130_FILTER_SELECT_MIN + filter_config->fs_max - |
| DIV64_U64_ROUND_CLOSEST(dividend, divisor); |
| |
| if (temp < AD4130_FILTER_SELECT_MIN) |
| temp = AD4130_FILTER_SELECT_MIN; |
| else if (temp > filter_config->fs_max) |
| temp = filter_config->fs_max; |
| |
| *fs = temp; |
| } |
| |
| static void ad4130_fs_to_freq(enum ad4130_filter_mode filter_mode, |
| unsigned int fs, int *val, int *val2) |
| { |
| const struct ad4130_filter_config *filter_config = |
| &ad4130_filter_configs[filter_mode]; |
| unsigned int dividend, divisor; |
| u64 temp; |
| |
| dividend = (filter_config->fs_max - fs + AD4130_FILTER_SELECT_MIN) * |
| AD4130_MAX_ODR; |
| divisor = filter_config->fs_max * filter_config->odr_div; |
| |
| temp = div_u64((u64)dividend * NANO, divisor); |
| *val = div_u64_rem(temp, NANO, val2); |
| } |
| |
| static int ad4130_set_filter_mode(struct iio_dev *indio_dev, |
| const struct iio_chan_spec *chan, |
| unsigned int val) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel = chan->scan_index; |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_setup_info *setup_info = &chan_info->setup; |
| enum ad4130_filter_mode old_filter_mode; |
| int freq_val, freq_val2; |
| unsigned int old_fs; |
| int ret = 0; |
| |
| mutex_lock(&st->lock); |
| if (setup_info->filter_mode == val) |
| goto out; |
| |
| old_fs = setup_info->fs; |
| old_filter_mode = setup_info->filter_mode; |
| |
| /* |
| * When switching between filter modes, try to match the ODR as |
| * close as possible. To do this, convert the current FS into ODR |
| * using the old filter mode, then convert it back into FS using |
| * the new filter mode. |
| */ |
| ad4130_fs_to_freq(setup_info->filter_mode, setup_info->fs, |
| &freq_val, &freq_val2); |
| |
| ad4130_freq_to_fs(val, freq_val, freq_val2, &setup_info->fs); |
| |
| setup_info->filter_mode = val; |
| |
| ret = ad4130_write_channel_setup(st, channel, false); |
| if (ret) { |
| setup_info->fs = old_fs; |
| setup_info->filter_mode = old_filter_mode; |
| } |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int ad4130_get_filter_mode(struct iio_dev *indio_dev, |
| const struct iio_chan_spec *chan) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel = chan->scan_index; |
| struct ad4130_setup_info *setup_info = &st->chans_info[channel].setup; |
| enum ad4130_filter_mode filter_mode; |
| |
| mutex_lock(&st->lock); |
| filter_mode = setup_info->filter_mode; |
| mutex_unlock(&st->lock); |
| |
| return filter_mode; |
| } |
| |
| static const struct iio_enum ad4130_filter_mode_enum = { |
| .items = ad4130_filter_modes_str, |
| .num_items = ARRAY_SIZE(ad4130_filter_modes_str), |
| .set = ad4130_set_filter_mode, |
| .get = ad4130_get_filter_mode, |
| }; |
| |
| static const struct iio_chan_spec_ext_info ad4130_filter_mode_ext_info[] = { |
| IIO_ENUM("filter_mode", IIO_SEPARATE, &ad4130_filter_mode_enum), |
| IIO_ENUM_AVAILABLE("filter_mode", IIO_SHARED_BY_TYPE, |
| &ad4130_filter_mode_enum), |
| { } |
| }; |
| |
| static const struct iio_chan_spec ad4130_channel_template = { |
| .type = IIO_VOLTAGE, |
| .indexed = 1, |
| .differential = 1, |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | |
| BIT(IIO_CHAN_INFO_SCALE) | |
| BIT(IIO_CHAN_INFO_OFFSET) | |
| BIT(IIO_CHAN_INFO_SAMP_FREQ), |
| .info_mask_separate_available = BIT(IIO_CHAN_INFO_SCALE) | |
| BIT(IIO_CHAN_INFO_SAMP_FREQ), |
| .ext_info = ad4130_filter_mode_ext_info, |
| .scan_type = { |
| .sign = 'u', |
| .endianness = IIO_BE, |
| }, |
| }; |
| |
| static int ad4130_set_channel_pga(struct ad4130_state *st, unsigned int channel, |
| int val, int val2) |
| { |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_setup_info *setup_info = &chan_info->setup; |
| unsigned int pga, old_pga; |
| int ret = 0; |
| |
| for (pga = 0; pga < AD4130_MAX_PGA; pga++) |
| if (val == st->scale_tbls[setup_info->ref_sel][pga][0] && |
| val2 == st->scale_tbls[setup_info->ref_sel][pga][1]) |
| break; |
| |
| if (pga == AD4130_MAX_PGA) |
| return -EINVAL; |
| |
| mutex_lock(&st->lock); |
| if (pga == setup_info->pga) |
| goto out; |
| |
| old_pga = setup_info->pga; |
| setup_info->pga = pga; |
| |
| ret = ad4130_write_channel_setup(st, channel, false); |
| if (ret) |
| setup_info->pga = old_pga; |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int ad4130_set_channel_freq(struct ad4130_state *st, |
| unsigned int channel, int val, int val2) |
| { |
| struct ad4130_chan_info *chan_info = &st->chans_info[channel]; |
| struct ad4130_setup_info *setup_info = &chan_info->setup; |
| unsigned int fs, old_fs; |
| int ret = 0; |
| |
| mutex_lock(&st->lock); |
| old_fs = setup_info->fs; |
| |
| ad4130_freq_to_fs(setup_info->filter_mode, val, val2, &fs); |
| |
| if (fs == setup_info->fs) |
| goto out; |
| |
| setup_info->fs = fs; |
| |
| ret = ad4130_write_channel_setup(st, channel, false); |
| if (ret) |
| setup_info->fs = old_fs; |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int _ad4130_read_sample(struct iio_dev *indio_dev, unsigned int channel, |
| int *val) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| ret = ad4130_set_channel_enable(st, channel, true); |
| if (ret) |
| return ret; |
| |
| reinit_completion(&st->completion); |
| |
| ret = ad4130_set_mode(st, AD4130_MODE_CONTINUOUS); |
| if (ret) |
| return ret; |
| |
| ret = wait_for_completion_timeout(&st->completion, |
| msecs_to_jiffies(1000)); |
| if (!ret) |
| return -ETIMEDOUT; |
| |
| ret = ad4130_set_mode(st, AD4130_MODE_IDLE); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(st->regmap, AD4130_DATA_REG, val); |
| if (ret) |
| return ret; |
| |
| ret = ad4130_set_channel_enable(st, channel, false); |
| if (ret) |
| return ret; |
| |
| return IIO_VAL_INT; |
| } |
| |
| static int ad4130_read_sample(struct iio_dev *indio_dev, unsigned int channel, |
| int *val) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| ret = iio_device_claim_direct_mode(indio_dev); |
| if (ret) |
| return ret; |
| |
| mutex_lock(&st->lock); |
| ret = _ad4130_read_sample(indio_dev, channel, val); |
| mutex_unlock(&st->lock); |
| |
| iio_device_release_direct_mode(indio_dev); |
| |
| return ret; |
| } |
| |
| static int ad4130_read_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int *val, int *val2, long info) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel = chan->scan_index; |
| struct ad4130_setup_info *setup_info = &st->chans_info[channel].setup; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_RAW: |
| return ad4130_read_sample(indio_dev, channel, val); |
| case IIO_CHAN_INFO_SCALE: |
| mutex_lock(&st->lock); |
| *val = st->scale_tbls[setup_info->ref_sel][setup_info->pga][0]; |
| *val2 = st->scale_tbls[setup_info->ref_sel][setup_info->pga][1]; |
| mutex_unlock(&st->lock); |
| |
| return IIO_VAL_INT_PLUS_NANO; |
| case IIO_CHAN_INFO_OFFSET: |
| *val = st->bipolar ? -BIT(chan->scan_type.realbits - 1) : 0; |
| |
| return IIO_VAL_INT; |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| mutex_lock(&st->lock); |
| ad4130_fs_to_freq(setup_info->filter_mode, setup_info->fs, |
| val, val2); |
| mutex_unlock(&st->lock); |
| |
| return IIO_VAL_INT_PLUS_NANO; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad4130_read_avail(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| const int **vals, int *type, int *length, |
| long info) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel = chan->scan_index; |
| struct ad4130_setup_info *setup_info = &st->chans_info[channel].setup; |
| const struct ad4130_filter_config *filter_config; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_SCALE: |
| *vals = (int *)st->scale_tbls[setup_info->ref_sel]; |
| *length = ARRAY_SIZE(st->scale_tbls[setup_info->ref_sel]) * 2; |
| |
| *type = IIO_VAL_INT_PLUS_NANO; |
| |
| return IIO_AVAIL_LIST; |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| mutex_lock(&st->lock); |
| filter_config = &ad4130_filter_configs[setup_info->filter_mode]; |
| mutex_unlock(&st->lock); |
| |
| *vals = (int *)filter_config->samp_freq_avail; |
| *length = filter_config->samp_freq_avail_len * 2; |
| *type = IIO_VAL_FRACTIONAL; |
| |
| return filter_config->samp_freq_avail_type; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad4130_write_raw_get_fmt(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| long info) |
| { |
| switch (info) { |
| case IIO_CHAN_INFO_SCALE: |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| return IIO_VAL_INT_PLUS_NANO; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad4130_write_raw(struct iio_dev *indio_dev, |
| struct iio_chan_spec const *chan, |
| int val, int val2, long info) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel = chan->scan_index; |
| |
| switch (info) { |
| case IIO_CHAN_INFO_SCALE: |
| return ad4130_set_channel_pga(st, channel, val, val2); |
| case IIO_CHAN_INFO_SAMP_FREQ: |
| return ad4130_set_channel_freq(st, channel, val, val2); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad4130_reg_access(struct iio_dev *indio_dev, unsigned int reg, |
| unsigned int writeval, unsigned int *readval) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| |
| if (readval) |
| return regmap_read(st->regmap, reg, readval); |
| |
| return regmap_write(st->regmap, reg, writeval); |
| } |
| |
| static int ad4130_update_scan_mode(struct iio_dev *indio_dev, |
| const unsigned long *scan_mask) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int channel; |
| unsigned int val = 0; |
| int ret; |
| |
| mutex_lock(&st->lock); |
| |
| for_each_set_bit(channel, scan_mask, indio_dev->num_channels) { |
| ret = ad4130_set_channel_enable(st, channel, true); |
| if (ret) |
| goto out; |
| |
| val++; |
| } |
| |
| st->num_enabled_channels = val; |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return 0; |
| } |
| |
| static int ad4130_set_fifo_watermark(struct iio_dev *indio_dev, unsigned int val) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int eff; |
| int ret; |
| |
| if (val > AD4130_FIFO_SIZE) |
| return -EINVAL; |
| |
| eff = val * st->num_enabled_channels; |
| if (eff > AD4130_FIFO_SIZE) |
| /* |
| * Always set watermark to a multiple of the number of |
| * enabled channels to avoid making the FIFO unaligned. |
| */ |
| eff = rounddown(AD4130_FIFO_SIZE, st->num_enabled_channels); |
| |
| mutex_lock(&st->lock); |
| |
| ret = regmap_update_bits(st->regmap, AD4130_FIFO_CONTROL_REG, |
| AD4130_FIFO_CONTROL_WM_MASK, |
| FIELD_PREP(AD4130_FIFO_CONTROL_WM_MASK, |
| ad4130_watermark_reg_val(eff))); |
| if (ret) |
| goto out; |
| |
| st->effective_watermark = eff; |
| st->watermark = val; |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static const struct iio_info ad4130_info = { |
| .read_raw = ad4130_read_raw, |
| .read_avail = ad4130_read_avail, |
| .write_raw_get_fmt = ad4130_write_raw_get_fmt, |
| .write_raw = ad4130_write_raw, |
| .update_scan_mode = ad4130_update_scan_mode, |
| .hwfifo_set_watermark = ad4130_set_fifo_watermark, |
| .debugfs_reg_access = ad4130_reg_access, |
| }; |
| |
| static int ad4130_buffer_postenable(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| int ret; |
| |
| mutex_lock(&st->lock); |
| |
| ret = ad4130_set_watermark_interrupt_en(st, true); |
| if (ret) |
| goto out; |
| |
| ret = irq_set_irq_type(st->spi->irq, st->inv_irq_trigger); |
| if (ret) |
| goto out; |
| |
| ret = ad4130_set_fifo_mode(st, AD4130_FIFO_MODE_WM); |
| if (ret) |
| goto out; |
| |
| ret = ad4130_set_mode(st, AD4130_MODE_CONTINUOUS); |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static int ad4130_buffer_predisable(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int i; |
| int ret; |
| |
| mutex_lock(&st->lock); |
| |
| ret = ad4130_set_mode(st, AD4130_MODE_IDLE); |
| if (ret) |
| goto out; |
| |
| ret = irq_set_irq_type(st->spi->irq, st->irq_trigger); |
| if (ret) |
| goto out; |
| |
| ret = ad4130_set_fifo_mode(st, AD4130_FIFO_MODE_DISABLED); |
| if (ret) |
| goto out; |
| |
| ret = ad4130_set_watermark_interrupt_en(st, false); |
| if (ret) |
| goto out; |
| |
| /* |
| * update_scan_mode() is not called in the disable path, disable all |
| * channels here. |
| */ |
| for (i = 0; i < indio_dev->num_channels; i++) { |
| ret = ad4130_set_channel_enable(st, i, false); |
| if (ret) |
| goto out; |
| } |
| |
| out: |
| mutex_unlock(&st->lock); |
| |
| return ret; |
| } |
| |
| static const struct iio_buffer_setup_ops ad4130_buffer_ops = { |
| .postenable = ad4130_buffer_postenable, |
| .predisable = ad4130_buffer_predisable, |
| }; |
| |
| static ssize_t hwfifo_watermark_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct ad4130_state *st = iio_priv(dev_to_iio_dev(dev)); |
| unsigned int val; |
| |
| mutex_lock(&st->lock); |
| val = st->watermark; |
| mutex_unlock(&st->lock); |
| |
| return sysfs_emit(buf, "%d\n", val); |
| } |
| |
| static ssize_t hwfifo_enabled_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct ad4130_state *st = iio_priv(dev_to_iio_dev(dev)); |
| unsigned int val; |
| int ret; |
| |
| ret = regmap_read(st->regmap, AD4130_FIFO_CONTROL_REG, &val); |
| if (ret) |
| return ret; |
| |
| val = FIELD_GET(AD4130_FIFO_CONTROL_MODE_MASK, val); |
| |
| return sysfs_emit(buf, "%d\n", val != AD4130_FIFO_MODE_DISABLED); |
| } |
| |
| static ssize_t hwfifo_watermark_min_show(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| return sysfs_emit(buf, "%s\n", "1"); |
| } |
| |
| static ssize_t hwfifo_watermark_max_show(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| return sysfs_emit(buf, "%s\n", __stringify(AD4130_FIFO_SIZE)); |
| } |
| |
| static IIO_DEVICE_ATTR_RO(hwfifo_watermark_min, 0); |
| static IIO_DEVICE_ATTR_RO(hwfifo_watermark_max, 0); |
| static IIO_DEVICE_ATTR_RO(hwfifo_watermark, 0); |
| static IIO_DEVICE_ATTR_RO(hwfifo_enabled, 0); |
| |
| static const struct iio_dev_attr *ad4130_fifo_attributes[] = { |
| &iio_dev_attr_hwfifo_watermark_min, |
| &iio_dev_attr_hwfifo_watermark_max, |
| &iio_dev_attr_hwfifo_watermark, |
| &iio_dev_attr_hwfifo_enabled, |
| NULL |
| }; |
| |
| static int _ad4130_find_table_index(const unsigned int *tbl, size_t len, |
| unsigned int val) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < len; i++) |
| if (tbl[i] == val) |
| return i; |
| |
| return -EINVAL; |
| } |
| |
| #define ad4130_find_table_index(table, val) \ |
| _ad4130_find_table_index(table, ARRAY_SIZE(table), val) |
| |
| static int ad4130_get_ref_voltage(struct ad4130_state *st, |
| enum ad4130_ref_sel ref_sel) |
| { |
| switch (ref_sel) { |
| case AD4130_REF_REFIN1: |
| return regulator_get_voltage(st->regulators[2].consumer); |
| case AD4130_REF_REFIN2: |
| return regulator_get_voltage(st->regulators[3].consumer); |
| case AD4130_REF_AVDD_AVSS: |
| return regulator_get_voltage(st->regulators[0].consumer); |
| case AD4130_REF_REFOUT_AVSS: |
| return st->int_ref_uv; |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int ad4130_parse_fw_setup(struct ad4130_state *st, |
| struct fwnode_handle *child, |
| struct ad4130_setup_info *setup_info) |
| { |
| struct device *dev = &st->spi->dev; |
| u32 tmp; |
| int ret; |
| |
| tmp = 0; |
| fwnode_property_read_u32(child, "adi,excitation-current-0-nanoamp", &tmp); |
| ret = ad4130_find_table_index(ad4130_iout_current_na_tbl, tmp); |
| if (ret < 0) |
| return dev_err_probe(dev, ret, |
| "Invalid excitation current %unA\n", tmp); |
| setup_info->iout0_val = ret; |
| |
| tmp = 0; |
| fwnode_property_read_u32(child, "adi,excitation-current-1-nanoamp", &tmp); |
| ret = ad4130_find_table_index(ad4130_iout_current_na_tbl, tmp); |
| if (ret < 0) |
| return dev_err_probe(dev, ret, |
| "Invalid excitation current %unA\n", tmp); |
| setup_info->iout1_val = ret; |
| |
| tmp = 0; |
| fwnode_property_read_u32(child, "adi,burnout-current-nanoamp", &tmp); |
| ret = ad4130_find_table_index(ad4130_burnout_current_na_tbl, tmp); |
| if (ret < 0) |
| return dev_err_probe(dev, ret, |
| "Invalid burnout current %unA\n", tmp); |
| setup_info->burnout = ret; |
| |
| setup_info->ref_bufp = fwnode_property_read_bool(child, "adi,buffered-positive"); |
| setup_info->ref_bufm = fwnode_property_read_bool(child, "adi,buffered-negative"); |
| |
| setup_info->ref_sel = AD4130_REF_REFIN1; |
| fwnode_property_read_u32(child, "adi,reference-select", |
| &setup_info->ref_sel); |
| if (setup_info->ref_sel >= AD4130_REF_SEL_MAX) |
| return dev_err_probe(dev, -EINVAL, |
| "Invalid reference selected %u\n", |
| setup_info->ref_sel); |
| |
| if (setup_info->ref_sel == AD4130_REF_REFOUT_AVSS) |
| st->int_ref_en = true; |
| |
| ret = ad4130_get_ref_voltage(st, setup_info->ref_sel); |
| if (ret < 0) |
| return dev_err_probe(dev, ret, "Cannot use reference %u\n", |
| setup_info->ref_sel); |
| |
| return 0; |
| } |
| |
| static int ad4130_validate_diff_channel(struct ad4130_state *st, u32 pin) |
| { |
| struct device *dev = &st->spi->dev; |
| |
| if (pin >= AD4130_MAX_DIFF_INPUTS) |
| return dev_err_probe(dev, -EINVAL, |
| "Invalid differential channel %u\n", pin); |
| |
| if (pin >= AD4130_MAX_ANALOG_PINS) |
| return 0; |
| |
| if (st->pins_fn[pin] == AD4130_PIN_FN_SPECIAL) |
| return dev_err_probe(dev, -EINVAL, |
| "Pin %u already used with fn %u\n", pin, |
| st->pins_fn[pin]); |
| |
| st->pins_fn[pin] |= AD4130_PIN_FN_DIFF; |
| |
| return 0; |
| } |
| |
| static int ad4130_validate_diff_channels(struct ad4130_state *st, |
| u32 *pins, unsigned int len) |
| { |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < len; i++) { |
| ret = ad4130_validate_diff_channel(st, pins[i]); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_validate_excitation_pin(struct ad4130_state *st, u32 pin) |
| { |
| struct device *dev = &st->spi->dev; |
| |
| if (pin >= AD4130_MAX_ANALOG_PINS) |
| return dev_err_probe(dev, -EINVAL, |
| "Invalid excitation pin %u\n", pin); |
| |
| if (st->pins_fn[pin] == AD4130_PIN_FN_SPECIAL) |
| return dev_err_probe(dev, -EINVAL, |
| "Pin %u already used with fn %u\n", pin, |
| st->pins_fn[pin]); |
| |
| st->pins_fn[pin] |= AD4130_PIN_FN_EXCITATION; |
| |
| return 0; |
| } |
| |
| static int ad4130_validate_vbias_pin(struct ad4130_state *st, u32 pin) |
| { |
| struct device *dev = &st->spi->dev; |
| |
| if (pin >= AD4130_MAX_ANALOG_PINS) |
| return dev_err_probe(dev, -EINVAL, "Invalid vbias pin %u\n", |
| pin); |
| |
| if (st->pins_fn[pin] == AD4130_PIN_FN_SPECIAL) |
| return dev_err_probe(dev, -EINVAL, |
| "Pin %u already used with fn %u\n", pin, |
| st->pins_fn[pin]); |
| |
| st->pins_fn[pin] |= AD4130_PIN_FN_VBIAS; |
| |
| return 0; |
| } |
| |
| static int ad4130_validate_vbias_pins(struct ad4130_state *st, |
| u32 *pins, unsigned int len) |
| { |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < st->num_vbias_pins; i++) { |
| ret = ad4130_validate_vbias_pin(st, pins[i]); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_parse_fw_channel(struct iio_dev *indio_dev, |
| struct fwnode_handle *child) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| unsigned int resolution = ad4130_resolution(st); |
| unsigned int index = indio_dev->num_channels++; |
| struct device *dev = &st->spi->dev; |
| struct ad4130_chan_info *chan_info; |
| struct iio_chan_spec *chan; |
| u32 pins[2]; |
| int ret; |
| |
| if (index >= AD4130_MAX_CHANNELS) |
| return dev_err_probe(dev, -EINVAL, "Too many channels\n"); |
| |
| chan = &st->chans[index]; |
| chan_info = &st->chans_info[index]; |
| |
| *chan = ad4130_channel_template; |
| chan->scan_type.realbits = resolution; |
| chan->scan_type.storagebits = resolution; |
| chan->scan_index = index; |
| |
| chan_info->slot = AD4130_INVALID_SLOT; |
| chan_info->setup.fs = AD4130_FILTER_SELECT_MIN; |
| chan_info->initialized = true; |
| |
| ret = fwnode_property_read_u32_array(child, "diff-channels", pins, |
| ARRAY_SIZE(pins)); |
| if (ret) |
| return ret; |
| |
| ret = ad4130_validate_diff_channels(st, pins, ARRAY_SIZE(pins)); |
| if (ret) |
| return ret; |
| |
| chan->channel = pins[0]; |
| chan->channel2 = pins[1]; |
| |
| ret = ad4130_parse_fw_setup(st, child, &chan_info->setup); |
| if (ret) |
| return ret; |
| |
| fwnode_property_read_u32(child, "adi,excitation-pin-0", |
| &chan_info->iout0); |
| if (chan_info->setup.iout0_val != AD4130_IOUT_OFF) { |
| ret = ad4130_validate_excitation_pin(st, chan_info->iout0); |
| if (ret) |
| return ret; |
| } |
| |
| fwnode_property_read_u32(child, "adi,excitation-pin-1", |
| &chan_info->iout1); |
| if (chan_info->setup.iout1_val != AD4130_IOUT_OFF) { |
| ret = ad4130_validate_excitation_pin(st, chan_info->iout1); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_parse_fw_children(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| struct device *dev = &st->spi->dev; |
| struct fwnode_handle *child; |
| int ret; |
| |
| indio_dev->channels = st->chans; |
| |
| device_for_each_child_node(dev, child) { |
| ret = ad4130_parse_fw_channel(indio_dev, child); |
| if (ret) { |
| fwnode_handle_put(child); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int ad4310_parse_fw(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| struct device *dev = &st->spi->dev; |
| u32 ext_clk_freq = AD4130_MCLK_FREQ_76_8KHZ; |
| unsigned int i; |
| int avdd_uv; |
| int irq; |
| int ret; |
| |
| st->mclk = devm_clk_get_optional(dev, "mclk"); |
| if (IS_ERR(st->mclk)) |
| return dev_err_probe(dev, PTR_ERR(st->mclk), |
| "Failed to get mclk\n"); |
| |
| st->int_pin_sel = AD4130_INT_PIN_INT; |
| |
| for (i = 0; i < ARRAY_SIZE(ad4130_int_pin_names); i++) { |
| irq = fwnode_irq_get_byname(dev_fwnode(dev), |
| ad4130_int_pin_names[i]); |
| if (irq > 0) { |
| st->int_pin_sel = i; |
| break; |
| } |
| } |
| |
| if (st->int_pin_sel == AD4130_INT_PIN_DOUT) |
| return dev_err_probe(dev, -EINVAL, |
| "Cannot use DOUT as interrupt pin\n"); |
| |
| if (st->int_pin_sel == AD4130_INT_PIN_P2) |
| st->pins_fn[AD4130_AIN3_P2] = AD4130_PIN_FN_SPECIAL; |
| |
| device_property_read_u32(dev, "adi,ext-clk-freq-hz", &ext_clk_freq); |
| if (ext_clk_freq != AD4130_MCLK_FREQ_153_6KHZ && |
| ext_clk_freq != AD4130_MCLK_FREQ_76_8KHZ) |
| return dev_err_probe(dev, -EINVAL, |
| "Invalid external clock frequency %u\n", |
| ext_clk_freq); |
| |
| if (st->mclk && ext_clk_freq == AD4130_MCLK_FREQ_153_6KHZ) |
| st->mclk_sel = AD4130_MCLK_153_6KHZ_EXT; |
| else if (st->mclk) |
| st->mclk_sel = AD4130_MCLK_76_8KHZ_EXT; |
| else |
| st->mclk_sel = AD4130_MCLK_76_8KHZ; |
| |
| if (st->int_pin_sel == AD4130_INT_PIN_CLK && |
| st->mclk_sel != AD4130_MCLK_76_8KHZ) |
| return dev_err_probe(dev, -EINVAL, |
| "Invalid clock %u for interrupt pin %u\n", |
| st->mclk_sel, st->int_pin_sel); |
| |
| st->int_ref_uv = AD4130_INT_REF_2_5V; |
| |
| /* |
| * When the AVDD supply is set to below 2.5V the internal reference of |
| * 1.25V should be selected. |
| * See datasheet page 37, section ADC REFERENCE. |
| */ |
| avdd_uv = regulator_get_voltage(st->regulators[0].consumer); |
| if (avdd_uv > 0 && avdd_uv < AD4130_INT_REF_2_5V) |
| st->int_ref_uv = AD4130_INT_REF_1_25V; |
| |
| st->bipolar = device_property_read_bool(dev, "adi,bipolar"); |
| |
| ret = device_property_count_u32(dev, "adi,vbias-pins"); |
| if (ret > 0) { |
| if (ret > AD4130_MAX_ANALOG_PINS) |
| return dev_err_probe(dev, -EINVAL, |
| "Too many vbias pins %u\n", ret); |
| |
| st->num_vbias_pins = ret; |
| |
| ret = device_property_read_u32_array(dev, "adi,vbias-pins", |
| st->vbias_pins, |
| st->num_vbias_pins); |
| if (ret) |
| return dev_err_probe(dev, ret, |
| "Failed to read vbias pins\n"); |
| |
| ret = ad4130_validate_vbias_pins(st, st->vbias_pins, |
| st->num_vbias_pins); |
| if (ret) |
| return ret; |
| } |
| |
| ret = ad4130_parse_fw_children(indio_dev); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static void ad4130_fill_scale_tbls(struct ad4130_state *st) |
| { |
| unsigned int pow = ad4130_resolution(st) - st->bipolar; |
| unsigned int i, j; |
| |
| for (i = 0; i < AD4130_REF_SEL_MAX; i++) { |
| int ret; |
| u64 nv; |
| |
| ret = ad4130_get_ref_voltage(st, i); |
| if (ret < 0) |
| continue; |
| |
| nv = (u64)ret * NANO; |
| |
| for (j = 0; j < AD4130_MAX_PGA; j++) |
| st->scale_tbls[i][j][1] = div_u64(nv >> (pow + j), MILLI); |
| } |
| } |
| |
| static void ad4130_clk_disable_unprepare(void *clk) |
| { |
| clk_disable_unprepare(clk); |
| } |
| |
| static int ad4130_set_mclk_sel(struct ad4130_state *st, |
| enum ad4130_mclk_sel mclk_sel) |
| { |
| return regmap_update_bits(st->regmap, AD4130_ADC_CONTROL_REG, |
| AD4130_ADC_CONTROL_MCLK_SEL_MASK, |
| FIELD_PREP(AD4130_ADC_CONTROL_MCLK_SEL_MASK, |
| mclk_sel)); |
| } |
| |
| static unsigned long ad4130_int_clk_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| return AD4130_MCLK_FREQ_76_8KHZ; |
| } |
| |
| static int ad4130_int_clk_is_enabled(struct clk_hw *hw) |
| { |
| struct ad4130_state *st = container_of(hw, struct ad4130_state, int_clk_hw); |
| |
| return st->mclk_sel == AD4130_MCLK_76_8KHZ_OUT; |
| } |
| |
| static int ad4130_int_clk_prepare(struct clk_hw *hw) |
| { |
| struct ad4130_state *st = container_of(hw, struct ad4130_state, int_clk_hw); |
| int ret; |
| |
| ret = ad4130_set_mclk_sel(st, AD4130_MCLK_76_8KHZ_OUT); |
| if (ret) |
| return ret; |
| |
| st->mclk_sel = AD4130_MCLK_76_8KHZ_OUT; |
| |
| return 0; |
| } |
| |
| static void ad4130_int_clk_unprepare(struct clk_hw *hw) |
| { |
| struct ad4130_state *st = container_of(hw, struct ad4130_state, int_clk_hw); |
| int ret; |
| |
| ret = ad4130_set_mclk_sel(st, AD4130_MCLK_76_8KHZ); |
| if (ret) |
| return; |
| |
| st->mclk_sel = AD4130_MCLK_76_8KHZ; |
| } |
| |
| static const struct clk_ops ad4130_int_clk_ops = { |
| .recalc_rate = ad4130_int_clk_recalc_rate, |
| .is_enabled = ad4130_int_clk_is_enabled, |
| .prepare = ad4130_int_clk_prepare, |
| .unprepare = ad4130_int_clk_unprepare, |
| }; |
| |
| static void ad4130_clk_del_provider(void *of_node) |
| { |
| of_clk_del_provider(of_node); |
| } |
| |
| static int ad4130_setup_int_clk(struct ad4130_state *st) |
| { |
| struct device *dev = &st->spi->dev; |
| struct device_node *of_node = dev_of_node(dev); |
| struct clk_init_data init; |
| const char *clk_name; |
| struct clk *clk; |
| int ret; |
| |
| if (st->int_pin_sel == AD4130_INT_PIN_CLK || |
| st->mclk_sel != AD4130_MCLK_76_8KHZ) |
| return 0; |
| |
| if (!of_node) |
| return 0; |
| |
| clk_name = of_node->name; |
| of_property_read_string(of_node, "clock-output-names", &clk_name); |
| |
| init.name = clk_name; |
| init.ops = &ad4130_int_clk_ops; |
| |
| st->int_clk_hw.init = &init; |
| clk = devm_clk_register(dev, &st->int_clk_hw); |
| if (IS_ERR(clk)) |
| return PTR_ERR(clk); |
| |
| ret = of_clk_add_provider(of_node, of_clk_src_simple_get, clk); |
| if (ret) |
| return ret; |
| |
| return devm_add_action_or_reset(dev, ad4130_clk_del_provider, of_node); |
| } |
| |
| static int ad4130_setup(struct iio_dev *indio_dev) |
| { |
| struct ad4130_state *st = iio_priv(indio_dev); |
| struct device *dev = &st->spi->dev; |
| unsigned int int_ref_val; |
| unsigned long rate = AD4130_MCLK_FREQ_76_8KHZ; |
| unsigned int val; |
| unsigned int i; |
| int ret; |
| |
| if (st->mclk_sel == AD4130_MCLK_153_6KHZ_EXT) |
| rate = AD4130_MCLK_FREQ_153_6KHZ; |
| |
| ret = clk_set_rate(st->mclk, rate); |
| if (ret) |
| return ret; |
| |
| ret = clk_prepare_enable(st->mclk); |
| if (ret) |
| return ret; |
| |
| ret = devm_add_action_or_reset(dev, ad4130_clk_disable_unprepare, |
| st->mclk); |
| if (ret) |
| return ret; |
| |
| if (st->int_ref_uv == AD4130_INT_REF_2_5V) |
| int_ref_val = AD4130_INT_REF_VAL_2_5V; |
| else |
| int_ref_val = AD4130_INT_REF_VAL_1_25V; |
| |
| /* Switch to SPI 4-wire mode. */ |
| val = FIELD_PREP(AD4130_ADC_CONTROL_CSB_EN_MASK, 1); |
| val |= FIELD_PREP(AD4130_ADC_CONTROL_BIPOLAR_MASK, st->bipolar); |
| val |= FIELD_PREP(AD4130_ADC_CONTROL_INT_REF_EN_MASK, st->int_ref_en); |
| val |= FIELD_PREP(AD4130_ADC_CONTROL_MODE_MASK, AD4130_MODE_IDLE); |
| val |= FIELD_PREP(AD4130_ADC_CONTROL_MCLK_SEL_MASK, st->mclk_sel); |
| val |= FIELD_PREP(AD4130_ADC_CONTROL_INT_REF_VAL_MASK, int_ref_val); |
| |
| ret = regmap_write(st->regmap, AD4130_ADC_CONTROL_REG, val); |
| if (ret) |
| return ret; |
| |
| /* |
| * Configure all GPIOs for output. If configured, the interrupt function |
| * of P2 takes priority over the GPIO out function. |
| */ |
| val = AD4130_IO_CONTROL_GPIO_CTRL_MASK; |
| val |= FIELD_PREP(AD4130_IO_CONTROL_INT_PIN_SEL_MASK, st->int_pin_sel); |
| |
| ret = regmap_write(st->regmap, AD4130_IO_CONTROL_REG, val); |
| if (ret) |
| return ret; |
| |
| val = 0; |
| for (i = 0; i < st->num_vbias_pins; i++) |
| val |= BIT(st->vbias_pins[i]); |
| |
| ret = regmap_write(st->regmap, AD4130_VBIAS_REG, val); |
| if (ret) |
| return ret; |
| |
| ret = regmap_update_bits(st->regmap, AD4130_FIFO_CONTROL_REG, |
| AD4130_FIFO_CONTROL_HEADER_MASK, 0); |
| if (ret) |
| return ret; |
| |
| /* FIFO watermark interrupt starts out as enabled, disable it. */ |
| ret = ad4130_set_watermark_interrupt_en(st, false); |
| if (ret) |
| return ret; |
| |
| /* Setup channels. */ |
| for (i = 0; i < indio_dev->num_channels; i++) { |
| struct ad4130_chan_info *chan_info = &st->chans_info[i]; |
| struct iio_chan_spec *chan = &st->chans[i]; |
| unsigned int val; |
| |
| val = FIELD_PREP(AD4130_CHANNEL_AINP_MASK, chan->channel) | |
| FIELD_PREP(AD4130_CHANNEL_AINM_MASK, chan->channel2) | |
| FIELD_PREP(AD4130_CHANNEL_IOUT1_MASK, chan_info->iout0) | |
| FIELD_PREP(AD4130_CHANNEL_IOUT2_MASK, chan_info->iout1); |
| |
| ret = regmap_write(st->regmap, AD4130_CHANNEL_X_REG(i), val); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ad4130_soft_reset(struct ad4130_state *st) |
| { |
| int ret; |
| |
| ret = spi_write(st->spi, st->reset_buf, sizeof(st->reset_buf)); |
| if (ret) |
| return ret; |
| |
| fsleep(AD4130_RESET_SLEEP_US); |
| |
| return 0; |
| } |
| |
| static void ad4130_disable_regulators(void *data) |
| { |
| struct ad4130_state *st = data; |
| |
| regulator_bulk_disable(ARRAY_SIZE(st->regulators), st->regulators); |
| } |
| |
| static int ad4130_probe(struct spi_device *spi) |
| { |
| struct device *dev = &spi->dev; |
| struct iio_dev *indio_dev; |
| struct ad4130_state *st; |
| int ret; |
| |
| indio_dev = devm_iio_device_alloc(dev, sizeof(*st)); |
| if (!indio_dev) |
| return -ENOMEM; |
| |
| st = iio_priv(indio_dev); |
| |
| memset(st->reset_buf, 0xff, sizeof(st->reset_buf)); |
| init_completion(&st->completion); |
| mutex_init(&st->lock); |
| st->spi = spi; |
| |
| /* |
| * Xfer: [ XFR1 ] [ XFR2 ] |
| * Master: 0x7D N ...................... |
| * Slave: ...... DATA1 DATA2 ... DATAN |
| */ |
| st->fifo_tx_buf[0] = AD4130_COMMS_READ_MASK | AD4130_FIFO_DATA_REG; |
| st->fifo_xfer[0].tx_buf = st->fifo_tx_buf; |
| st->fifo_xfer[0].len = sizeof(st->fifo_tx_buf); |
| st->fifo_xfer[1].rx_buf = st->fifo_rx_buf; |
| spi_message_init_with_transfers(&st->fifo_msg, st->fifo_xfer, |
| ARRAY_SIZE(st->fifo_xfer)); |
| |
| indio_dev->name = AD4130_NAME; |
| indio_dev->modes = INDIO_DIRECT_MODE; |
| indio_dev->info = &ad4130_info; |
| |
| st->regmap = devm_regmap_init(dev, NULL, st, &ad4130_regmap_config); |
| if (IS_ERR(st->regmap)) |
| return PTR_ERR(st->regmap); |
| |
| st->regulators[0].supply = "avdd"; |
| st->regulators[1].supply = "iovdd"; |
| st->regulators[2].supply = "refin1"; |
| st->regulators[3].supply = "refin2"; |
| |
| ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(st->regulators), |
| st->regulators); |
| if (ret) |
| return dev_err_probe(dev, ret, "Failed to get regulators\n"); |
| |
| ret = regulator_bulk_enable(ARRAY_SIZE(st->regulators), st->regulators); |
| if (ret) |
| return dev_err_probe(dev, ret, "Failed to enable regulators\n"); |
| |
| ret = devm_add_action_or_reset(dev, ad4130_disable_regulators, st); |
| if (ret) |
| return dev_err_probe(dev, ret, |
| "Failed to add regulators disable action\n"); |
| |
| ret = ad4130_soft_reset(st); |
| if (ret) |
| return ret; |
| |
| ret = ad4310_parse_fw(indio_dev); |
| if (ret) |
| return ret; |
| |
| ret = ad4130_setup(indio_dev); |
| if (ret) |
| return ret; |
| |
| ret = ad4130_setup_int_clk(st); |
| if (ret) |
| return ret; |
| |
| ad4130_fill_scale_tbls(st); |
| |
| st->gc.owner = THIS_MODULE; |
| st->gc.label = AD4130_NAME; |
| st->gc.base = -1; |
| st->gc.ngpio = AD4130_MAX_GPIOS; |
| st->gc.parent = dev; |
| st->gc.can_sleep = true; |
| st->gc.init_valid_mask = ad4130_gpio_init_valid_mask; |
| st->gc.get_direction = ad4130_gpio_get_direction; |
| st->gc.set = ad4130_gpio_set; |
| |
| ret = devm_gpiochip_add_data(dev, &st->gc, st); |
| if (ret) |
| return ret; |
| |
| ret = devm_iio_kfifo_buffer_setup_ext(dev, indio_dev, |
| &ad4130_buffer_ops, |
| ad4130_fifo_attributes); |
| if (ret) |
| return ret; |
| |
| ret = devm_request_threaded_irq(dev, spi->irq, NULL, |
| ad4130_irq_handler, IRQF_ONESHOT, |
| indio_dev->name, indio_dev); |
| if (ret) |
| return dev_err_probe(dev, ret, "Failed to request irq\n"); |
| |
| /* |
| * When the chip enters FIFO mode, IRQ polarity is inverted. |
| * When the chip exits FIFO mode, IRQ polarity returns to normal. |
| * See datasheet pages: 65, FIFO Watermark Interrupt section, |
| * and 71, Bit Descriptions for STATUS Register, RDYB. |
| * Cache the normal and inverted IRQ triggers to set them when |
| * entering and exiting FIFO mode. |
| */ |
| st->irq_trigger = irq_get_trigger_type(spi->irq); |
| if (st->irq_trigger & IRQF_TRIGGER_RISING) |
| st->inv_irq_trigger = IRQF_TRIGGER_FALLING; |
| else if (st->irq_trigger & IRQF_TRIGGER_FALLING) |
| st->inv_irq_trigger = IRQF_TRIGGER_RISING; |
| else |
| return dev_err_probe(dev, -EINVAL, "Invalid irq flags: %u\n", |
| st->irq_trigger); |
| |
| return devm_iio_device_register(dev, indio_dev); |
| } |
| |
| static const struct of_device_id ad4130_of_match[] = { |
| { |
| .compatible = "adi,ad4130", |
| }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, ad4130_of_match); |
| |
| static struct spi_driver ad4130_driver = { |
| .driver = { |
| .name = AD4130_NAME, |
| .of_match_table = ad4130_of_match, |
| }, |
| .probe = ad4130_probe, |
| }; |
| module_spi_driver(ad4130_driver); |
| |
| MODULE_AUTHOR("Cosmin Tanislav <cosmin.tanislav@analog.com>"); |
| MODULE_DESCRIPTION("Analog Devices AD4130 SPI driver"); |
| MODULE_LICENSE("GPL"); |