| #!/bin/bash | |
| # SPDX-License-Identifier: GPL-2.0 | |
| # | |
| # Test various interface configuration scenarios. Observe that configurations | |
| # deemed valid by mlxsw succeed, invalid configurations fail and that no traces | |
| # are produced. To prevent the test from passing in case traces are produced, | |
| # the user can set the 'kernel.panic_on_warn' and 'kernel.panic_on_oops' | |
| # sysctls in its environment. | |
| lib_dir=$(dirname $0)/../../../net/forwarding | |
| ALL_TESTS=" | |
| rif_set_addr_test | |
| rif_vrf_set_addr_test | |
| rif_inherit_bridge_addr_test | |
| rif_non_inherit_bridge_addr_test | |
| vlan_interface_deletion_test | |
| bridge_deletion_test | |
| bridge_vlan_flags_test | |
| vlan_1_test | |
| lag_bridge_upper_test | |
| duplicate_vlans_test | |
| vlan_rif_refcount_test | |
| subport_rif_refcount_test | |
| vlan_dev_deletion_test | |
| lag_unlink_slaves_test | |
| lag_dev_deletion_test | |
| vlan_interface_uppers_test | |
| bridge_extern_learn_test | |
| neigh_offload_test | |
| nexthop_offload_test | |
| devlink_reload_test | |
| " | |
| NUM_NETIFS=2 | |
| : ${TIMEOUT:=20000} # ms | |
| source $lib_dir/lib.sh | |
| source $lib_dir/devlink_lib.sh | |
| setup_prepare() | |
| { | |
| swp1=${NETIFS[p1]} | |
| swp2=${NETIFS[p2]} | |
| ip link set dev $swp1 up | |
| ip link set dev $swp2 up | |
| } | |
| cleanup() | |
| { | |
| pre_cleanup | |
| ip link set dev $swp2 down | |
| ip link set dev $swp1 down | |
| } | |
| rif_set_addr_test() | |
| { | |
| local swp1_mac=$(mac_get $swp1) | |
| local swp2_mac=$(mac_get $swp2) | |
| RET=0 | |
| # $swp1 and $swp2 likely got their IPv6 local addresses already, but | |
| # here we need to test the transition to RIF. | |
| ip addr flush dev $swp1 | |
| ip addr flush dev $swp2 | |
| sleep .1 | |
| ip addr add dev $swp1 192.0.2.1/28 | |
| check_err $? | |
| ip link set dev $swp1 addr 00:11:22:33:44:55 | |
| check_err $? | |
| # IP address enablement should be rejected if the MAC address prefix | |
| # doesn't match other RIFs. | |
| ip addr add dev $swp2 192.0.2.2/28 &>/dev/null | |
| check_fail $? "IP address addition passed for a device with a wrong MAC" | |
| ip addr add dev $swp2 192.0.2.2/28 2>&1 >/dev/null \ | |
| | grep -q mlxsw_spectrum | |
| check_err $? "no extack for IP address addition" | |
| ip link set dev $swp2 addr 00:11:22:33:44:66 | |
| check_err $? | |
| ip addr add dev $swp2 192.0.2.2/28 &>/dev/null | |
| check_err $? | |
| # Change of MAC address of a RIF should be forbidden if the new MAC | |
| # doesn't share the prefix with other MAC addresses. | |
| ip link set dev $swp2 addr 00:11:22:33:00:66 &>/dev/null | |
| check_fail $? "change of MAC address passed for a wrong MAC" | |
| ip link set dev $swp2 addr 00:11:22:33:00:66 2>&1 >/dev/null \ | |
| | grep -q mlxsw_spectrum | |
| check_err $? "no extack for MAC address change" | |
| log_test "RIF - bad MAC change" | |
| ip addr del dev $swp2 192.0.2.2/28 | |
| ip addr del dev $swp1 192.0.2.1/28 | |
| ip link set dev $swp2 addr $swp2_mac | |
| ip link set dev $swp1 addr $swp1_mac | |
| } | |
| rif_vrf_set_addr_test() | |
| { | |
| # Test that it is possible to set an IP address on a VRF upper despite | |
| # its random MAC address. | |
| RET=0 | |
| ip link add name vrf-test type vrf table 10 | |
| ip link set dev $swp1 master vrf-test | |
| ip -4 address add 192.0.2.1/24 dev vrf-test | |
| check_err $? "failed to set IPv4 address on VRF" | |
| ip -6 address add 2001:db8:1::1/64 dev vrf-test | |
| check_err $? "failed to set IPv6 address on VRF" | |
| log_test "RIF - setting IP address on VRF" | |
| ip link del dev vrf-test | |
| } | |
| rif_inherit_bridge_addr_test() | |
| { | |
| RET=0 | |
| # Create first RIF | |
| ip addr add dev $swp1 192.0.2.1/28 | |
| check_err $? | |
| # Create a FID RIF | |
| ip link add name br1 up type bridge vlan_filtering 0 | |
| ip link set dev $swp2 master br1 | |
| ip addr add dev br1 192.0.2.17/28 | |
| check_err $? | |
| # Prepare a device with a low MAC address | |
| ip link add name d up type dummy | |
| ip link set dev d addr 00:11:22:33:44:55 | |
| # Attach the device to br1. That prompts bridge address change, which | |
| # should be vetoed, thus preventing the attachment. | |
| ip link set dev d master br1 &>/dev/null | |
| check_fail $? "Device with low MAC was permitted to attach a bridge with RIF" | |
| ip link set dev d master br1 2>&1 >/dev/null \ | |
| | grep -q mlxsw_spectrum | |
| check_err $? "no extack for bridge attach rejection" | |
| ip link set dev $swp2 addr 00:11:22:33:44:55 &>/dev/null | |
| check_fail $? "Changing swp2's MAC address permitted" | |
| ip link set dev $swp2 addr 00:11:22:33:44:55 2>&1 >/dev/null \ | |
| | grep -q mlxsw_spectrum | |
| check_err $? "no extack for bridge port MAC address change rejection" | |
| log_test "RIF - attach port with bad MAC to bridge" | |
| ip link del dev d | |
| ip link del dev br1 | |
| ip addr del dev $swp1 192.0.2.1/28 | |
| } | |
| rif_non_inherit_bridge_addr_test() | |
| { | |
| local swp2_mac=$(mac_get $swp2) | |
| RET=0 | |
| # Create first RIF | |
| ip addr add dev $swp1 192.0.2.1/28 | |
| check_err $? | |
| # Create a FID RIF | |
| ip link add name br1 up type bridge vlan_filtering 0 | |
| ip link set dev br1 addr $swp2_mac | |
| ip link set dev $swp2 master br1 | |
| ip addr add dev br1 192.0.2.17/28 | |
| check_err $? | |
| # Prepare a device with a low MAC address | |
| ip link add name d up type dummy | |
| ip link set dev d addr 00:11:22:33:44:55 | |
| # Attach the device to br1. Since the bridge address was set, it should | |
| # work. | |
| ip link set dev d master br1 &>/dev/null | |
| check_err $? "Could not attach a device with low MAC to a bridge with RIF" | |
| # Port MAC address change should be allowed for a bridge with set MAC. | |
| ip link set dev $swp2 addr 00:11:22:33:44:55 | |
| check_err $? "Changing swp2's MAC address not permitted" | |
| log_test "RIF - attach port with bad MAC to bridge with set MAC" | |
| ip link set dev $swp2 addr $swp2_mac | |
| ip link del dev d | |
| ip link del dev br1 | |
| ip addr del dev $swp1 192.0.2.1/28 | |
| } | |
| vlan_interface_deletion_test() | |
| { | |
| # Test that when a VLAN interface is deleted, its associated router | |
| # interface (RIF) is correctly deleted and not leaked. See commit | |
| # c360867ec46a ("mlxsw: spectrum: Delete RIF when VLAN device is | |
| # removed") for more details | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| ip link add link br0 name br0.10 type vlan id 10 | |
| ip -6 address add 2001:db8:1::1/64 dev br0.10 | |
| ip link del dev br0.10 | |
| # If we leaked the previous RIF, then this should produce a trace | |
| ip link add link br0 name br0.20 type vlan id 20 | |
| ip -6 address add 2001:db8:1::1/64 dev br0.20 | |
| ip link del dev br0.20 | |
| log_test "vlan interface deletion" | |
| ip link del dev br0 | |
| } | |
| bridge_deletion_test() | |
| { | |
| # Test that when a bridge with VLAN interfaces is deleted, we correctly | |
| # delete the associated RIFs. See commit 602b74eda813 ("mlxsw: | |
| # spectrum_switchdev: Do not leak RIFs when removing bridge") for more | |
| # details | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| ip -6 address add 2001:db8::1/64 dev br0 | |
| ip link add link br0 name br0.10 type vlan id 10 | |
| ip -6 address add 2001:db8:1::1/64 dev br0.10 | |
| ip link add link br0 name br0.20 type vlan id 20 | |
| ip -6 address add 2001:db8:2::1/64 dev br0.20 | |
| ip link del dev br0 | |
| # If we leaked previous RIFs, then this should produce a trace | |
| ip -6 address add 2001:db8:1::1/64 dev $swp1 | |
| ip -6 address del 2001:db8:1::1/64 dev $swp1 | |
| log_test "bridge deletion" | |
| } | |
| bridge_vlan_flags_test() | |
| { | |
| # Test that when bridge VLAN flags are toggled, we do not take | |
| # unnecessary references on related structs. See commit 9e25826ffc94 | |
| # ("mlxsw: spectrum_switchdev: Fix port_vlan refcounting") for more | |
| # details | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| bridge vlan add vid 10 dev $swp1 pvid untagged | |
| bridge vlan add vid 10 dev $swp1 untagged | |
| bridge vlan add vid 10 dev $swp1 pvid | |
| bridge vlan add vid 10 dev $swp1 | |
| ip link del dev br0 | |
| # If we did not handle references correctly, then this should produce a | |
| # trace | |
| devlink dev reload "$DEVLINK_DEV" | |
| # Allow netdevices to be re-created following the reload | |
| sleep 20 | |
| log_test "bridge vlan flags" | |
| } | |
| vlan_1_test() | |
| { | |
| # Test that VLAN 1 can be configured over mlxsw ports. In the past it | |
| # was used internally for untagged traffic. See commit 47bf9df2e820 | |
| # ("mlxsw: spectrum: Forbid creation of VLAN 1 over port/LAG") for more | |
| # details | |
| RET=0 | |
| ip link add link $swp1 name $swp1.1 type vlan id 1 | |
| check_err $? "did not manage to create vlan 1 when should" | |
| log_test "vlan 1" | |
| ip link del dev $swp1.1 | |
| } | |
| lag_bridge_upper_test() | |
| { | |
| # Test that ports cannot be enslaved to LAG devices that have uppers | |
| # and that failure is handled gracefully. See commit b3529af6bb0d | |
| # ("spectrum: Reference count VLAN entries") for more details | |
| RET=0 | |
| ip link add name bond1 type bond mode 802.3ad | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev bond1 master br0 | |
| ip link set dev $swp1 down | |
| ip link set dev $swp1 master bond1 &> /dev/null | |
| check_fail $? "managed to enslave port to lag when should not" | |
| # This might generate a trace, if we did not handle the failure | |
| # correctly | |
| ip -6 address add 2001:db8:1::1/64 dev $swp1 | |
| ip -6 address del 2001:db8:1::1/64 dev $swp1 | |
| log_test "lag with bridge upper" | |
| ip link del dev br0 | |
| ip link del dev bond1 | |
| } | |
| duplicate_vlans_test() | |
| { | |
| # Test that on a given port a VLAN is only used once. Either as VLAN | |
| # in a VLAN-aware bridge or as a VLAN device | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| bridge vlan add vid 10 dev $swp1 | |
| ip link add link $swp1 name $swp1.10 type vlan id 10 &> /dev/null | |
| check_fail $? "managed to create vlan device when should not" | |
| bridge vlan del vid 10 dev $swp1 | |
| ip link add link $swp1 name $swp1.10 type vlan id 10 | |
| check_err $? "did not manage to create vlan device when should" | |
| bridge vlan add vid 10 dev $swp1 &> /dev/null | |
| check_fail $? "managed to add bridge vlan when should not" | |
| log_test "duplicate vlans" | |
| ip link del dev $swp1.10 | |
| ip link del dev br0 | |
| } | |
| vlan_rif_refcount_test() | |
| { | |
| # Test that RIFs representing VLAN interfaces are not affected from | |
| # ports member in the VLAN. We use the offload indication on routes | |
| # configured on the RIF to understand if it was created / destroyed | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| ip link set dev $swp1 up | |
| ip link set dev br0 up | |
| ip link add link br0 name br0.10 up type vlan id 10 | |
| ip -6 address add 2001:db8:1::1/64 dev br0.10 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev br0.10 | |
| check_err $? "vlan rif was not created before adding port to vlan" | |
| bridge vlan add vid 10 dev $swp1 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev br0.10 | |
| check_err $? "vlan rif was destroyed after adding port to vlan" | |
| bridge vlan del vid 10 dev $swp1 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev br0.10 | |
| check_err $? "vlan rif was destroyed after removing port from vlan" | |
| ip link set dev $swp1 nomaster | |
| busywait "$TIMEOUT" not wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev br0.10 | |
| check_err $? "vlan rif was not destroyed after unlinking port from bridge" | |
| log_test "vlan rif refcount" | |
| ip link del dev br0.10 | |
| ip link set dev $swp1 down | |
| ip link del dev br0 | |
| } | |
| subport_rif_refcount_test() | |
| { | |
| # Test that RIFs representing upper devices of physical ports are | |
| # reference counted correctly and destroyed when should. We use the | |
| # offload indication on routes configured on the RIF to understand if | |
| # it was created / destroyed | |
| RET=0 | |
| ip link add name bond1 type bond mode 802.3ad | |
| ip link set dev $swp1 down | |
| ip link set dev $swp2 down | |
| ip link set dev $swp1 master bond1 | |
| ip link set dev $swp2 master bond1 | |
| ip link set dev bond1 up | |
| ip link add link bond1 name bond1.10 up type vlan id 10 | |
| ip -6 address add 2001:db8:1::1/64 dev bond1 | |
| ip -6 address add 2001:db8:2::1/64 dev bond1.10 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev bond1 | |
| check_err $? "subport rif was not created on lag device" | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:2::2 dev bond1.10 | |
| check_err $? "subport rif was not created on vlan device" | |
| ip link set dev $swp1 nomaster | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev bond1 | |
| check_err $? "subport rif of lag device was destroyed when should not" | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:2::2 dev bond1.10 | |
| check_err $? "subport rif of vlan device was destroyed when should not" | |
| ip link set dev $swp2 nomaster | |
| busywait "$TIMEOUT" not wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:1::2 dev bond1 | |
| check_err $? "subport rif of lag device was not destroyed when should" | |
| busywait "$TIMEOUT" not wait_for_offload \ | |
| ip -6 route get fibmatch 2001:db8:2::2 dev bond1.10 | |
| check_err $? "subport rif of vlan device was not destroyed when should" | |
| log_test "subport rif refcount" | |
| ip link del dev bond1.10 | |
| ip link del dev bond1 | |
| } | |
| vlan_dev_deletion_test() | |
| { | |
| # Test that VLAN devices are correctly deleted / unlinked when enslaved | |
| # to bridge | |
| RET=0 | |
| ip link add name br10 type bridge | |
| ip link add name br20 type bridge | |
| ip link add name br30 type bridge | |
| ip link add link $swp1 name $swp1.10 type vlan id 10 | |
| ip link add link $swp1 name $swp1.20 type vlan id 20 | |
| ip link add link $swp1 name $swp1.30 type vlan id 30 | |
| ip link set dev $swp1.10 master br10 | |
| ip link set dev $swp1.20 master br20 | |
| ip link set dev $swp1.30 master br30 | |
| # If we did not handle the situation correctly, then these operations | |
| # might produce a trace | |
| ip link set dev $swp1.30 nomaster | |
| ip link del dev $swp1.20 | |
| # Deletion via ioctl uses different code paths from netlink | |
| vconfig rem $swp1.10 &> /dev/null | |
| log_test "vlan device deletion" | |
| ip link del dev $swp1.30 | |
| ip link del dev br30 | |
| ip link del dev br20 | |
| ip link del dev br10 | |
| } | |
| lag_create() | |
| { | |
| ip link add name bond1 type bond mode 802.3ad | |
| ip link set dev $swp1 down | |
| ip link set dev $swp2 down | |
| ip link set dev $swp1 master bond1 | |
| ip link set dev $swp2 master bond1 | |
| ip link add link bond1 name bond1.10 type vlan id 10 | |
| ip link add link bond1 name bond1.20 type vlan id 20 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev bond1 master br0 | |
| ip link add name br10 type bridge | |
| ip link set dev bond1.10 master br10 | |
| ip link add name br20 type bridge | |
| ip link set dev bond1.20 master br20 | |
| } | |
| lag_unlink_slaves_test() | |
| { | |
| # Test that ports are correctly unlinked from their LAG master, when | |
| # the LAG and its VLAN uppers are enslaved to bridges | |
| RET=0 | |
| lag_create | |
| ip link set dev $swp1 nomaster | |
| check_err $? "lag slave $swp1 was not unlinked from master" | |
| ip link set dev $swp2 nomaster | |
| check_err $? "lag slave $swp2 was not unlinked from master" | |
| # Try to configure corresponding VLANs as router interfaces | |
| ip -6 address add 2001:db8:1::1/64 dev $swp1 | |
| check_err $? "failed to configure ip address on $swp1" | |
| ip link add link $swp1 name $swp1.10 type vlan id 10 | |
| ip -6 address add 2001:db8:10::1/64 dev $swp1.10 | |
| check_err $? "failed to configure ip address on $swp1.10" | |
| ip link add link $swp1 name $swp1.20 type vlan id 20 | |
| ip -6 address add 2001:db8:20::1/64 dev $swp1.20 | |
| check_err $? "failed to configure ip address on $swp1.20" | |
| log_test "lag slaves unlinking" | |
| ip link del dev $swp1.20 | |
| ip link del dev $swp1.10 | |
| ip address flush dev $swp1 | |
| ip link del dev br20 | |
| ip link del dev br10 | |
| ip link del dev br0 | |
| ip link del dev bond1 | |
| } | |
| lag_dev_deletion_test() | |
| { | |
| # Test that LAG device is correctly deleted, when the LAG and its VLAN | |
| # uppers are enslaved to bridges | |
| RET=0 | |
| lag_create | |
| ip link del dev bond1 | |
| log_test "lag device deletion" | |
| ip link del dev br20 | |
| ip link del dev br10 | |
| ip link del dev br0 | |
| } | |
| vlan_interface_uppers_test() | |
| { | |
| # Test that uppers of a VLAN interface are correctly sanitized | |
| RET=0 | |
| ip link add name br0 type bridge vlan_filtering 1 | |
| ip link set dev $swp1 master br0 | |
| ip link add link br0 name br0.10 type vlan id 10 | |
| ip link add link br0.10 name macvlan0 \ | |
| type macvlan mode private &> /dev/null | |
| check_fail $? "managed to create a macvlan when should not" | |
| ip -6 address add 2001:db8:1::1/64 dev br0.10 | |
| ip link add link br0.10 name macvlan0 type macvlan mode private | |
| check_err $? "did not manage to create a macvlan when should" | |
| ip link del dev macvlan0 | |
| ip link add name vrf-test type vrf table 10 | |
| ip link set dev br0.10 master vrf-test | |
| check_err $? "did not manage to enslave vlan interface to vrf" | |
| ip link del dev vrf-test | |
| ip link add name br-test type bridge | |
| ip link set dev br0.10 master br-test &> /dev/null | |
| check_fail $? "managed to enslave vlan interface to bridge when should not" | |
| ip link del dev br-test | |
| log_test "vlan interface uppers" | |
| ip link del dev br0 | |
| } | |
| bridge_extern_learn_test() | |
| { | |
| # Test that externally learned entries added from user space are | |
| # marked as offloaded | |
| RET=0 | |
| ip link add name br0 type bridge | |
| ip link set dev $swp1 master br0 | |
| bridge fdb add de:ad:be:ef:13:37 dev $swp1 master extern_learn | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| bridge fdb show brport $swp1 de:ad:be:ef:13:37 | |
| check_err $? "fdb entry not marked as offloaded when should" | |
| log_test "externally learned fdb entry" | |
| ip link del dev br0 | |
| } | |
| neigh_offload_test() | |
| { | |
| # Test that IPv4 and IPv6 neighbour entries are marked as offloaded | |
| RET=0 | |
| ip -4 address add 192.0.2.1/24 dev $swp1 | |
| ip -6 address add 2001:db8:1::1/64 dev $swp1 | |
| ip -4 neigh add 192.0.2.2 lladdr de:ad:be:ef:13:37 nud perm dev $swp1 | |
| ip -6 neigh add 2001:db8:1::2 lladdr de:ad:be:ef:13:37 nud perm \ | |
| dev $swp1 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -4 neigh show dev $swp1 192.0.2.2 | |
| check_err $? "ipv4 neigh entry not marked as offloaded when should" | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 neigh show dev $swp1 2001:db8:1::2 | |
| check_err $? "ipv6 neigh entry not marked as offloaded when should" | |
| log_test "neighbour offload indication" | |
| ip -6 neigh del 2001:db8:1::2 dev $swp1 | |
| ip -4 neigh del 192.0.2.2 dev $swp1 | |
| ip -6 address del 2001:db8:1::1/64 dev $swp1 | |
| ip -4 address del 192.0.2.1/24 dev $swp1 | |
| } | |
| nexthop_offload_test() | |
| { | |
| # Test that IPv4 and IPv6 nexthops are marked as offloaded | |
| RET=0 | |
| sysctl_set net.ipv6.conf.$swp2.keep_addr_on_down 1 | |
| simple_if_init $swp1 192.0.2.1/24 2001:db8:1::1/64 | |
| simple_if_init $swp2 192.0.2.2/24 2001:db8:1::2/64 | |
| setup_wait | |
| ip -4 route add 198.51.100.0/24 vrf v$swp1 \ | |
| nexthop via 192.0.2.2 dev $swp1 | |
| ip -6 route add 2001:db8:2::/64 vrf v$swp1 \ | |
| nexthop via 2001:db8:1::2 dev $swp1 | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -4 route show 198.51.100.0/24 vrf v$swp1 | |
| check_err $? "ipv4 nexthop not marked as offloaded when should" | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route show 2001:db8:2::/64 vrf v$swp1 | |
| check_err $? "ipv6 nexthop not marked as offloaded when should" | |
| ip link set dev $swp2 down | |
| sleep 1 | |
| busywait "$TIMEOUT" not wait_for_offload \ | |
| ip -4 route show 198.51.100.0/24 vrf v$swp1 | |
| check_err $? "ipv4 nexthop marked as offloaded when should not" | |
| busywait "$TIMEOUT" not wait_for_offload \ | |
| ip -6 route show 2001:db8:2::/64 vrf v$swp1 | |
| check_err $? "ipv6 nexthop marked as offloaded when should not" | |
| ip link set dev $swp2 up | |
| setup_wait | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -4 route show 198.51.100.0/24 vrf v$swp1 | |
| check_err $? "ipv4 nexthop not marked as offloaded after neigh add" | |
| busywait "$TIMEOUT" wait_for_offload \ | |
| ip -6 route show 2001:db8:2::/64 vrf v$swp1 | |
| check_err $? "ipv6 nexthop not marked as offloaded after neigh add" | |
| log_test "nexthop offload indication" | |
| ip -6 route del 2001:db8:2::/64 vrf v$swp1 | |
| ip -4 route del 198.51.100.0/24 vrf v$swp1 | |
| simple_if_fini $swp2 192.0.2.2/24 2001:db8:1::2/64 | |
| simple_if_fini $swp1 192.0.2.1/24 2001:db8:1::1/64 | |
| sysctl_restore net.ipv6.conf.$swp2.keep_addr_on_down | |
| } | |
| devlink_reload_test() | |
| { | |
| # Test that after executing all the above configuration tests, a | |
| # devlink reload can be performed without errors | |
| RET=0 | |
| devlink dev reload "$DEVLINK_DEV" | |
| check_err $? "devlink reload failed" | |
| log_test "devlink reload - last test" | |
| sleep 20 | |
| } | |
| trap cleanup EXIT | |
| setup_prepare | |
| setup_wait | |
| tests_run | |
| exit $EXIT_STATUS |