| // SPDX-License-Identifier: GPL-2.0 | |
| /* | |
| * SoC core Device Tree for the ARM Integrator platforms | |
| */ | |
| / { | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| memory { | |
| device_type = "memory"; | |
| reg = <0x0 0x0>; | |
| }; | |
| core-module@10000000 { | |
| compatible = "arm,core-module-integrator", "syscon", "simple-mfd"; | |
| reg = <0x10000000 0x200>; | |
| ranges = <0x0 0x10000000 0x200>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| /* Use core module LED to indicate CPU load */ | |
| led@c,0 { | |
| compatible = "register-bit-led"; | |
| reg = <0x0c 0x04>; | |
| offset = <0x0c>; | |
| mask = <0x01>; | |
| label = "integrator:core_module"; | |
| linux,default-trigger = "cpu0"; | |
| default-state = "on"; | |
| }; | |
| }; | |
| ebi@12000000 { | |
| compatible = "arm,external-bus-interface"; | |
| reg = <0x12000000 0x100>; | |
| }; | |
| timer@13000000 { | |
| reg = <0x13000000 0x100>; | |
| interrupt-parent = <&pic>; | |
| interrupts = <5>; | |
| }; | |
| timer@13000100 { | |
| reg = <0x13000100 0x100>; | |
| interrupt-parent = <&pic>; | |
| interrupts = <6>; | |
| }; | |
| timer@13000200 { | |
| reg = <0x13000200 0x100>; | |
| interrupt-parent = <&pic>; | |
| interrupts = <7>; | |
| }; | |
| pic@14000000 { | |
| compatible = "arm,versatile-fpga-irq"; | |
| #interrupt-cells = <1>; | |
| interrupt-controller; | |
| reg = <0x14000000 0x100>; | |
| clear-mask = <0xffffffff>; | |
| }; | |
| flash@24000000 { | |
| compatible = "arm,versatile-flash", "cfi-flash"; | |
| reg = <0x24000000 0x02000000>; | |
| bank-width = <4>; | |
| partitions { | |
| compatible = "arm,arm-firmware-suite"; | |
| }; | |
| }; | |
| fpga { | |
| compatible = "simple-bus"; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| ranges; | |
| interrupt-parent = <&pic>; | |
| /* | |
| * These PrimeCells are in the same locations and using the | |
| * same interrupts in all Integrators, however the silicon | |
| * version deployed is different. | |
| */ | |
| rtc@15000000 { | |
| reg = <0x15000000 0x1000>; | |
| interrupts = <8>; | |
| }; | |
| uart@16000000 { | |
| reg = <0x16000000 0x1000>; | |
| interrupts = <1>; | |
| }; | |
| uart@17000000 { | |
| reg = <0x17000000 0x1000>; | |
| interrupts = <2>; | |
| }; | |
| kmi@18000000 { | |
| reg = <0x18000000 0x1000>; | |
| interrupts = <3>; | |
| }; | |
| kmi@19000000 { | |
| reg = <0x19000000 0x1000>; | |
| interrupts = <4>; | |
| }; | |
| syscon@1a000000 { | |
| /* Debug registers mapped as syscon */ | |
| compatible = "syscon", "simple-mfd"; | |
| reg = <0x1a000000 0x10>; | |
| ranges = <0x0 0x1a000000 0x10>; | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| led@4,0 { | |
| compatible = "register-bit-led"; | |
| reg = <0x04 0x04>; | |
| offset = <0x04>; | |
| mask = <0x01>; | |
| label = "integrator:green0"; | |
| linux,default-trigger = "heartbeat"; | |
| default-state = "on"; | |
| }; | |
| led@4,1 { | |
| compatible = "register-bit-led"; | |
| reg = <0x04 0x04>; | |
| offset = <0x04>; | |
| mask = <0x02>; | |
| label = "integrator:yellow"; | |
| default-state = "off"; | |
| }; | |
| led@4,2 { | |
| compatible = "register-bit-led"; | |
| reg = <0x04 0x04>; | |
| offset = <0x04>; | |
| mask = <0x04>; | |
| label = "integrator:red"; | |
| default-state = "off"; | |
| }; | |
| led@4,3 { | |
| compatible = "register-bit-led"; | |
| reg = <0x04 0x04>; | |
| offset = <0x04>; | |
| mask = <0x08>; | |
| label = "integrator:green1"; | |
| default-state = "off"; | |
| }; | |
| }; | |
| }; | |
| }; |