| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * linux/arch/arm/mach-omap1/board-fsample.c | |
| * | |
| * Modified from board-perseus2.c | |
| * | |
| * Original OMAP730 support by Jean Pihet <j-pihet@ti.com> | |
| * Updated for 2.6 by Kevin Hilman <kjh@hilman.org> | |
| */ | |
| #include <linux/gpio.h> | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/delay.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/platnand.h> | |
| #include <linux/mtd/physmap.h> | |
| #include <linux/input.h> | |
| #include <linux/smc91x.h> | |
| #include <linux/omapfb.h> | |
| #include <asm/mach-types.h> | |
| #include <asm/mach/arch.h> | |
| #include <asm/mach/map.h> | |
| #include <mach/tc.h> | |
| #include <mach/mux.h> | |
| #include "flash.h" | |
| #include <linux/platform_data/keypad-omap.h> | |
| #include <mach/hardware.h> | |
| #include "iomap.h" | |
| #include "common.h" | |
| #include "fpga.h" | |
| /* fsample is pretty close to p2-sample */ | |
| #define fsample_cpld_read(reg) __raw_readb(reg) | |
| #define fsample_cpld_write(val, reg) __raw_writeb(val, reg) | |
| #define FSAMPLE_CPLD_BASE 0xE8100000 | |
| #define FSAMPLE_CPLD_SIZE SZ_4K | |
| #define FSAMPLE_CPLD_START 0x05080000 | |
| #define FSAMPLE_CPLD_REG_A (FSAMPLE_CPLD_BASE + 0x00) | |
| #define FSAMPLE_CPLD_SWITCH (FSAMPLE_CPLD_BASE + 0x02) | |
| #define FSAMPLE_CPLD_UART (FSAMPLE_CPLD_BASE + 0x02) | |
| #define FSAMPLE_CPLD_REG_B (FSAMPLE_CPLD_BASE + 0x04) | |
| #define FSAMPLE_CPLD_VERSION (FSAMPLE_CPLD_BASE + 0x06) | |
| #define FSAMPLE_CPLD_SET_CLR (FSAMPLE_CPLD_BASE + 0x06) | |
| #define FSAMPLE_CPLD_BIT_BT_RESET 0 | |
| #define FSAMPLE_CPLD_BIT_LCD_RESET 1 | |
| #define FSAMPLE_CPLD_BIT_CAM_PWDN 2 | |
| #define FSAMPLE_CPLD_BIT_CHARGER_ENABLE 3 | |
| #define FSAMPLE_CPLD_BIT_SD_MMC_EN 4 | |
| #define FSAMPLE_CPLD_BIT_aGPS_PWREN 5 | |
| #define FSAMPLE_CPLD_BIT_BACKLIGHT 6 | |
| #define FSAMPLE_CPLD_BIT_aGPS_EN_RESET 7 | |
| #define FSAMPLE_CPLD_BIT_aGPS_SLEEPx_N 8 | |
| #define FSAMPLE_CPLD_BIT_OTG_RESET 9 | |
| #define fsample_cpld_set(bit) \ | |
| fsample_cpld_write((((bit) & 15) << 4) | 0x0f, FSAMPLE_CPLD_SET_CLR) | |
| #define fsample_cpld_clear(bit) \ | |
| fsample_cpld_write(0xf0 | ((bit) & 15), FSAMPLE_CPLD_SET_CLR) | |
| static const unsigned int fsample_keymap[] = { | |
| KEY(0, 0, KEY_UP), | |
| KEY(1, 0, KEY_RIGHT), | |
| KEY(2, 0, KEY_LEFT), | |
| KEY(3, 0, KEY_DOWN), | |
| KEY(4, 0, KEY_ENTER), | |
| KEY(0, 1, KEY_F10), | |
| KEY(1, 1, KEY_SEND), | |
| KEY(2, 1, KEY_END), | |
| KEY(3, 1, KEY_VOLUMEDOWN), | |
| KEY(4, 1, KEY_VOLUMEUP), | |
| KEY(5, 1, KEY_RECORD), | |
| KEY(0, 2, KEY_F9), | |
| KEY(1, 2, KEY_3), | |
| KEY(2, 2, KEY_6), | |
| KEY(3, 2, KEY_9), | |
| KEY(4, 2, KEY_KPDOT), | |
| KEY(0, 3, KEY_BACK), | |
| KEY(1, 3, KEY_2), | |
| KEY(2, 3, KEY_5), | |
| KEY(3, 3, KEY_8), | |
| KEY(4, 3, KEY_0), | |
| KEY(5, 3, KEY_KPSLASH), | |
| KEY(0, 4, KEY_HOME), | |
| KEY(1, 4, KEY_1), | |
| KEY(2, 4, KEY_4), | |
| KEY(3, 4, KEY_7), | |
| KEY(4, 4, KEY_KPASTERISK), | |
| KEY(5, 4, KEY_POWER), | |
| }; | |
| static struct smc91x_platdata smc91x_info = { | |
| .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, | |
| .leda = RPC_LED_100_10, | |
| .ledb = RPC_LED_TX_RX, | |
| }; | |
| static struct resource smc91x_resources[] = { | |
| [0] = { | |
| .start = H2P2_DBG_FPGA_ETHR_START, /* Physical */ | |
| .end = H2P2_DBG_FPGA_ETHR_START + 0xf, | |
| .flags = IORESOURCE_MEM, | |
| }, | |
| [1] = { | |
| .start = INT_7XX_MPU_EXT_NIRQ, | |
| .end = 0, | |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, | |
| }, | |
| }; | |
| static void __init fsample_init_smc91x(void) | |
| { | |
| __raw_writeb(1, H2P2_DBG_FPGA_LAN_RESET); | |
| mdelay(50); | |
| __raw_writeb(__raw_readb(H2P2_DBG_FPGA_LAN_RESET) & ~1, | |
| H2P2_DBG_FPGA_LAN_RESET); | |
| mdelay(50); | |
| } | |
| static struct mtd_partition nor_partitions[] = { | |
| /* bootloader (U-Boot, etc) in first sector */ | |
| { | |
| .name = "bootloader", | |
| .offset = 0, | |
| .size = SZ_128K, | |
| .mask_flags = MTD_WRITEABLE, /* force read-only */ | |
| }, | |
| /* bootloader params in the next sector */ | |
| { | |
| .name = "params", | |
| .offset = MTDPART_OFS_APPEND, | |
| .size = SZ_128K, | |
| .mask_flags = 0, | |
| }, | |
| /* kernel */ | |
| { | |
| .name = "kernel", | |
| .offset = MTDPART_OFS_APPEND, | |
| .size = SZ_2M, | |
| .mask_flags = 0 | |
| }, | |
| /* rest of flash is a file system */ | |
| { | |
| .name = "rootfs", | |
| .offset = MTDPART_OFS_APPEND, | |
| .size = MTDPART_SIZ_FULL, | |
| .mask_flags = 0 | |
| }, | |
| }; | |
| static struct physmap_flash_data nor_data = { | |
| .width = 2, | |
| .set_vpp = omap1_set_vpp, | |
| .parts = nor_partitions, | |
| .nr_parts = ARRAY_SIZE(nor_partitions), | |
| }; | |
| static struct resource nor_resource = { | |
| .start = OMAP_CS0_PHYS, | |
| .end = OMAP_CS0_PHYS + SZ_32M - 1, | |
| .flags = IORESOURCE_MEM, | |
| }; | |
| static struct platform_device nor_device = { | |
| .name = "physmap-flash", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &nor_data, | |
| }, | |
| .num_resources = 1, | |
| .resource = &nor_resource, | |
| }; | |
| #define FSAMPLE_NAND_RB_GPIO_PIN 62 | |
| static int nand_dev_ready(struct nand_chip *chip) | |
| { | |
| return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN); | |
| } | |
| static struct platform_nand_data nand_data = { | |
| .chip = { | |
| .nr_chips = 1, | |
| .chip_offset = 0, | |
| .options = NAND_SAMSUNG_LP_OPTIONS, | |
| }, | |
| .ctrl = { | |
| .cmd_ctrl = omap1_nand_cmd_ctl, | |
| .dev_ready = nand_dev_ready, | |
| }, | |
| }; | |
| static struct resource nand_resource = { | |
| .start = OMAP_CS3_PHYS, | |
| .end = OMAP_CS3_PHYS + SZ_4K - 1, | |
| .flags = IORESOURCE_MEM, | |
| }; | |
| static struct platform_device nand_device = { | |
| .name = "gen_nand", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &nand_data, | |
| }, | |
| .num_resources = 1, | |
| .resource = &nand_resource, | |
| }; | |
| static struct platform_device smc91x_device = { | |
| .name = "smc91x", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &smc91x_info, | |
| }, | |
| .num_resources = ARRAY_SIZE(smc91x_resources), | |
| .resource = smc91x_resources, | |
| }; | |
| static struct resource kp_resources[] = { | |
| [0] = { | |
| .start = INT_7XX_MPUIO_KEYPAD, | |
| .end = INT_7XX_MPUIO_KEYPAD, | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static const struct matrix_keymap_data fsample_keymap_data = { | |
| .keymap = fsample_keymap, | |
| .keymap_size = ARRAY_SIZE(fsample_keymap), | |
| }; | |
| static struct omap_kp_platform_data kp_data = { | |
| .rows = 8, | |
| .cols = 8, | |
| .keymap_data = &fsample_keymap_data, | |
| .delay = 4, | |
| }; | |
| static struct platform_device kp_device = { | |
| .name = "omap-keypad", | |
| .id = -1, | |
| .dev = { | |
| .platform_data = &kp_data, | |
| }, | |
| .num_resources = ARRAY_SIZE(kp_resources), | |
| .resource = kp_resources, | |
| }; | |
| static struct platform_device *devices[] __initdata = { | |
| &nor_device, | |
| &nand_device, | |
| &smc91x_device, | |
| &kp_device, | |
| }; | |
| static const struct omap_lcd_config fsample_lcd_config = { | |
| .ctrl_name = "internal", | |
| }; | |
| static void __init omap_fsample_init(void) | |
| { | |
| /* Early, board-dependent init */ | |
| /* | |
| * Hold GSM Reset until needed | |
| */ | |
| omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL); | |
| /* | |
| * UARTs -> done automagically by 8250 driver | |
| */ | |
| /* | |
| * CSx timings, GPIO Mux ... setup | |
| */ | |
| /* Flash: CS0 timings setup */ | |
| omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0); | |
| omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0); | |
| /* | |
| * Ethernet support through the debug board | |
| * CS1 timings setup | |
| */ | |
| omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1); | |
| omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1); | |
| /* | |
| * Configure MPU_EXT_NIRQ IO in IO_CONF9 register, | |
| * It is used as the Ethernet controller interrupt | |
| */ | |
| omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, | |
| OMAP7XX_IO_CONF_9); | |
| fsample_init_smc91x(); | |
| BUG_ON(gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0); | |
| gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN); | |
| omap_cfg_reg(L3_1610_FLASH_CS2B_OE); | |
| omap_cfg_reg(M8_1610_FLASH_CS2B_WE); | |
| /* Mux pins for keypad */ | |
| omap_cfg_reg(E2_7XX_KBR0); | |
| omap_cfg_reg(J7_7XX_KBR1); | |
| omap_cfg_reg(E1_7XX_KBR2); | |
| omap_cfg_reg(F3_7XX_KBR3); | |
| omap_cfg_reg(D2_7XX_KBR4); | |
| omap_cfg_reg(C2_7XX_KBC0); | |
| omap_cfg_reg(D3_7XX_KBC1); | |
| omap_cfg_reg(E4_7XX_KBC2); | |
| omap_cfg_reg(F4_7XX_KBC3); | |
| omap_cfg_reg(E3_7XX_KBC4); | |
| platform_add_devices(devices, ARRAY_SIZE(devices)); | |
| omap_serial_init(); | |
| omap_register_i2c_bus(1, 100, NULL, 0); | |
| omapfb_set_lcd_config(&fsample_lcd_config); | |
| } | |
| /* Only FPGA needs to be mapped here. All others are done with ioremap */ | |
| static struct map_desc omap_fsample_io_desc[] __initdata = { | |
| { | |
| .virtual = H2P2_DBG_FPGA_BASE, | |
| .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START), | |
| .length = H2P2_DBG_FPGA_SIZE, | |
| .type = MT_DEVICE | |
| }, | |
| { | |
| .virtual = FSAMPLE_CPLD_BASE, | |
| .pfn = __phys_to_pfn(FSAMPLE_CPLD_START), | |
| .length = FSAMPLE_CPLD_SIZE, | |
| .type = MT_DEVICE | |
| } | |
| }; | |
| static void __init omap_fsample_map_io(void) | |
| { | |
| omap15xx_map_io(); | |
| iotable_init(omap_fsample_io_desc, | |
| ARRAY_SIZE(omap_fsample_io_desc)); | |
| } | |
| MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample") | |
| /* Maintainer: Brian Swetland <swetland@google.com> */ | |
| .atag_offset = 0x100, | |
| .map_io = omap_fsample_map_io, | |
| .init_early = omap1_init_early, | |
| .init_irq = omap1_init_irq, | |
| .handle_irq = omap1_handle_irq, | |
| .init_machine = omap_fsample_init, | |
| .init_late = omap1_init_late, | |
| .init_time = omap1_timer_init, | |
| .restart = omap1_restart, | |
| MACHINE_END |