blob: 16f7d3b30e1dbf023e0229fe946441516fc3c845 [file] [log] [blame]
/*
* FSL SoC setup code
*
* Maintained by Kumar Gala (see MAINTAINERS for contact information)
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/config.h>
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <linux/irq.h>
#include <linux/module.h>
#include <asm/system.h>
#include <asm/atomic.h>
#include <asm/io.h>
#include <asm/pci-bridge.h>
#include <asm/prom.h>
#include <sysdev/fsl_soc.h>
#undef DEBUG
#ifdef DEBUG
#define DBG(x...) printk(x)
#else
#define DBG(x...)
#endif
int mpc83xx_pci2_busno;
int mpc83xx_exclude_device(u_char bus, u_char devfn)
{
if (bus == 0 && PCI_SLOT(devfn) == 0)
return PCIBIOS_DEVICE_NOT_FOUND;
if (mpc83xx_pci2_busno)
if (bus == (mpc83xx_pci2_busno) && PCI_SLOT(devfn) == 0)
return PCIBIOS_DEVICE_NOT_FOUND;
return PCIBIOS_SUCCESSFUL;
}
int __init add_bridge(struct device_node *dev)
{
int len;
struct pci_controller *hose;
struct resource rsrc;
int *bus_range;
int primary = 1, has_address = 0;
phys_addr_t immr = get_immrbase();
DBG("Adding PCI host bridge %s\n", dev->full_name);
/* Fetch host bridge registers address */
has_address = (of_address_to_resource(dev, 0, &rsrc) == 0);
/* Get bus range if any */
bus_range = (int *)get_property(dev, "bus-range", &len);
if (bus_range == NULL || len < 2 * sizeof(int)) {
printk(KERN_WARNING "Can't get bus-range for %s, assume"
" bus 0\n", dev->full_name);
}
hose = pcibios_alloc_controller();
if (!hose)
return -ENOMEM;
hose->arch_data = dev;
hose->set_cfg_type = 1;
hose->first_busno = bus_range ? bus_range[0] : 0;
hose->last_busno = bus_range ? bus_range[1] : 0xff;
/* MPC83xx supports up to two host controllers one at 0x8500 from immrbar
* the other at 0x8600, we consider the 0x8500 the primary controller
*/
/* PCI 1 */
if ((rsrc.start & 0xfffff) == 0x8500) {
setup_indirect_pci(hose, immr + 0x8300, immr + 0x8304);
}
/* PCI 2 */
if ((rsrc.start & 0xfffff) == 0x8600) {
setup_indirect_pci(hose, immr + 0x8380, immr + 0x8384);
primary = 0;
hose->bus_offset = hose->first_busno;
mpc83xx_pci2_busno = hose->first_busno;
}
printk(KERN_INFO "Found MPC83xx PCI host bridge at 0x%08lx. "
"Firmware bus number: %d->%d\n",
rsrc.start, hose->first_busno, hose->last_busno);
DBG(" ->Hose at 0x%p, cfg_addr=0x%p,cfg_data=0x%p\n",
hose, hose->cfg_addr, hose->cfg_data);
/* Interpret the "ranges" property */
/* This also maps the I/O region and sets isa_io/mem_base */
pci_process_bridge_OF_ranges(hose, dev, primary);
return 0;
}