blob: d4eba5c0ce0262ae2b5885d7022ddb3cc38e6e87 [file] [log] [blame]
/*
* Copyright (C) 2005 SAN People
* Copyright (C) 2008 Atmel
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
#include <linux/clk.h>
#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
#include <mach/gpio.h>
#include "generic.h"
static void __init ek_map_io(void)
{
/* Initialize processor: 18.432 MHz crystal */
at91sam9260_initialize(18432000);
/* DGBU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
| ATMEL_UART_RI);
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static void __init ek_init_irq(void)
{
at91sam9260_init_interrupts(NULL);
}
/*
* USB Host port
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
};
/*
* USB Device port
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PC5,
.pullup_pin = 0, /* pull-up driven by UDC */
};
/*
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
#if !defined(CONFIG_MMC_AT91)
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 1,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
#endif
};
/*
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PA7,
.is_rmii = 1,
};
/*
* NAND flash
*/
static struct mtd_partition __initdata ek_nand_partition[] = {
{
.name = "Bootstrap",
.offset = 0,
.size = 4 * 1024 * 1024,
},
{
.name = "Partition 1",
.offset = 4 * 1024 * 1024,
.size = 60 * 1024 * 1024,
},
{
.name = "Partition 2",
.offset = 64 * 1024 * 1024,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(ek_nand_partition);
return ek_nand_partition;
}
/* det_pin is not connected */
static struct atmel_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
.rdy_pin = AT91_PIN_PC13,
.enable_pin = AT91_PIN_PC14,
.partition_info = nand_partitions,
#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#endif
};
/*
* MCI (SD/MMC)
* det_pin, wp_pin and vcc_pin are not connected
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.slot_b = 1,
.wire4 = 1,
};
/*
* LEDs
*/
static struct gpio_led ek_leds[] = {
{ /* "bottom" led, green, userled1 to be defined */
.name = "ds5",
.gpio = AT91_PIN_PA6,
.active_low = 1,
.default_trigger = "none",
},
{ /* "power" led, yellow */
.name = "ds1",
.gpio = AT91_PIN_PA9,
.default_trigger = "heartbeat",
}
};
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
at91_add_device_mmc(0, &ek_mmc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
}
MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
/* Maintainer: Atmel */
.phys_io = AT91_BASE_SYS,
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91sam926x_timer,
.map_io = ek_map_io,
.init_irq = ek_init_irq,
.init_machine = ek_board_init,
MACHINE_END