blob: 9969dbab19e36e3f2bd1210c93840bc85bfd7f16 [file] [log] [blame]
/*
* MTX-1 platform devices registration (Au1500)
*
* Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/leds.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <mtd/mtd-abi.h>
#include <asm/bootinfo.h>
#include <asm/reboot.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-au1x00/au1xxx_eth.h>
#include <prom.h>
const char *get_system_type(void)
{
return "MTX-1";
}
void __init prom_init(void)
{
unsigned char *memsize_str;
unsigned long memsize;
prom_argc = fw_arg0;
prom_argv = (char **)fw_arg1;
prom_envp = (char **)fw_arg2;
prom_init_cmdline();
memsize_str = prom_getenv("memsize");
if (!memsize_str)
memsize = 0x04000000;
else
strict_strtoul(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
void prom_putchar(unsigned char c)
{
alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
}
static void mtx1_reset(char *c)
{
/* Jump to the reset vector */
__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
}
static void mtx1_power_off(void)
{
while (1)
asm volatile (
" .set mips32 \n"
" wait \n"
" .set mips0 \n");
}
void __init board_setup(void)
{
#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
/* Enable USB power switch */
alchemy_gpio_direction_output(204, 0);
#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */
/* Initialize sys_pinfunc */
au_writel(SYS_PF_NI2, SYS_PINFUNC);
/* Initialize GPIO */
au_writel(~0, KSEG1ADDR(AU1000_SYS_PHYS_ADDR) + SYS_TRIOUTCLR);
alchemy_gpio_direction_output(0, 0); /* Disable M66EN (PCI 66MHz) */
alchemy_gpio_direction_output(3, 1); /* Disable PCI CLKRUN# */
alchemy_gpio_direction_output(1, 1); /* Enable EXT_IO3 */
alchemy_gpio_direction_output(5, 0); /* Disable eth PHY TX_ER */
/* Enable LED and set it to green */
alchemy_gpio_direction_output(211, 1); /* green on */
alchemy_gpio_direction_output(212, 0); /* red off */
pm_power_off = mtx1_power_off;
_machine_halt = mtx1_power_off;
_machine_restart = mtx1_reset;
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
/******************************************************************************/
static struct gpio_keys_button mtx1_gpio_button[] = {
{
.gpio = 207,
.code = BTN_0,
.desc = "System button",
}
};
static struct gpio_keys_platform_data mtx1_buttons_data = {
.buttons = mtx1_gpio_button,
.nbuttons = ARRAY_SIZE(mtx1_gpio_button),
};
static struct platform_device mtx1_button = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &mtx1_buttons_data,
}
};
static struct resource mtx1_wdt_res[] = {
[0] = {
.start = 215,
.end = 215,
.name = "mtx1-wdt-gpio",
.flags = IORESOURCE_IRQ,
}
};
static struct platform_device mtx1_wdt = {
.name = "mtx1-wdt",
.id = 0,
.num_resources = ARRAY_SIZE(mtx1_wdt_res),
.resource = mtx1_wdt_res,
};
static struct gpio_led default_leds[] = {
{
.name = "mtx1:green",
.gpio = 211,
}, {
.name = "mtx1:red",
.gpio = 212,
},
};
static struct gpio_led_platform_data mtx1_led_data = {
.num_leds = ARRAY_SIZE(default_leds),
.leds = default_leds,
};
static struct platform_device mtx1_gpio_leds = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &mtx1_led_data,
}
};
static struct mtd_partition mtx1_mtd_partitions[] = {
{
.name = "filesystem",
.size = 0x01C00000,
.offset = 0,
},
{
.name = "yamon",
.size = 0x00100000,
.offset = MTDPART_OFS_APPEND,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "kernel",
.size = 0x002c0000,
.offset = MTDPART_OFS_APPEND,
},
{
.name = "yamon env",
.size = 0x00040000,
.offset = MTDPART_OFS_APPEND,
},
};
static struct physmap_flash_data mtx1_flash_data = {
.width = 4,
.nr_parts = 4,
.parts = mtx1_mtd_partitions,
};
static struct resource mtx1_mtd_resource = {
.start = 0x1e000000,
.end = 0x1fffffff,
.flags = IORESOURCE_MEM,
};
static struct platform_device mtx1_mtd = {
.name = "physmap-flash",
.dev = {
.platform_data = &mtx1_flash_data,
},
.num_resources = 1,
.resource = &mtx1_mtd_resource,
};
static struct resource alchemy_pci_host_res[] = {
[0] = {
.start = AU1500_PCI_PHYS_ADDR,
.end = AU1500_PCI_PHYS_ADDR + 0xfff,
.flags = IORESOURCE_MEM,
},
};
static int mtx1_pci_idsel(unsigned int devsel, int assert)
{
/* This function is only necessary to support a proprietary Cardbus
* adapter on the mtx-1 "singleboard" variant. It triggers a custom
* logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
*/
udelay(1);
if (assert && devsel != 0)
/* Suppress signal to Cardbus */
alchemy_gpio_set_value(1, 0); /* set EXT_IO3 OFF */
else
alchemy_gpio_set_value(1, 1); /* set EXT_IO3 ON */
udelay(1);
return 1;
}
static const char mtx1_irqtab[][5] = {
[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
[1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
[2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
[3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
[4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
[5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
[6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
[7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
};
static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
{
return mtx1_irqtab[slot][pin];
}
static struct alchemy_pci_platdata mtx1_pci_pd = {
.board_map_irq = mtx1_map_pci_irq,
.board_pci_idsel = mtx1_pci_idsel,
.pci_cfg_set = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
PCI_CONFIG_CH |
#if defined(__MIPSEB__)
PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
#else
0,
#endif
};
static struct platform_device mtx1_pci_host = {
.dev.platform_data = &mtx1_pci_pd,
.name = "alchemy-pci",
.id = 0,
.num_resources = ARRAY_SIZE(alchemy_pci_host_res),
.resource = alchemy_pci_host_res,
};
static struct platform_device *mtx1_devs[] __initdata = {
&mtx1_pci_host,
&mtx1_gpio_leds,
&mtx1_wdt,
&mtx1_button,
&mtx1_mtd,
};
static struct au1000_eth_platform_data mtx1_au1000_eth0_pdata = {
.phy_search_highest_addr = 1,
.phy1_search_mac0 = 1,
};
static int __init mtx1_register_devices(void)
{
int rc;
irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata);
rc = gpio_request(mtx1_gpio_button[0].gpio,
mtx1_gpio_button[0].desc);
if (rc < 0) {
printk(KERN_INFO "mtx1: failed to request %d\n",
mtx1_gpio_button[0].gpio);
goto out;
}
gpio_direction_input(mtx1_gpio_button[0].gpio);
out:
return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
}
arch_initcall(mtx1_register_devices);