blob: 8968dd7aebed2133b0103b39d7b752916dbfaab0 [file] [log] [blame]
#
# Broadcom pinctrl drivers
#
config PINCTRL_BCM281XX
bool "Broadcom BCM281xx pinctrl driver"
depends on OF && (ARCH_BCM_MOBILE || COMPILE_TEST)
select PINMUX
select PINCONF
select GENERIC_PINCONF
select REGMAP_MMIO
default ARCH_BCM_MOBILE
help
Say Y here to support Broadcom BCM281xx pinctrl driver, which is used
for the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
BCM28145, and BCM28155 SoCs. This driver requires the pinctrl
framework. GPIO is provided by a separate GPIO driver.
config PINCTRL_BCM2835
bool
select PINMUX
select PINCONF
select GPIOLIB_IRQCHIP
config PINCTRL_IPROC_GPIO
bool "Broadcom iProc GPIO (with PINCONF) driver"
depends on OF_GPIO && (ARCH_BCM_IPROC || COMPILE_TEST)
select GPIOLIB_IRQCHIP
select PINCONF
select GENERIC_PINCONF
default ARCH_BCM_IPROC
help
Say yes here to enable the Broadcom iProc GPIO driver.
The Broadcom iProc based SoCs- Cygnus, NS2, NSP and Stingray, use
same GPIO Controller IP hence this driver could be used for all.
The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU
GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and
the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are
supported by this driver.
The Broadcom NSP has two GPIO controllers including the ChipcommonA
GPIO, the ChipcommonB GPIO. Later controller is supported by this
driver.
The Broadcom NS2 has two GPIO controller including the CRMU GPIO,
the ChipcommonG GPIO. Both controllers are supported by this driver.
The Broadcom Stingray GPIO controllers are supported by this driver.
All above SoCs GPIO controllers support basic PINCONF functions such
as bias pull up, pull down, and drive strength configurations, when
these pins are muxed to GPIO.
It provides the framework where pins from the individual GPIO can be
individually muxed to GPIO function, through interaction with the
SoCs IOMUX controller. This features could be used only on SoCs which
support individual pin muxing.
config PINCTRL_CYGNUS_MUX
bool "Broadcom Cygnus IOMUX driver"
depends on (ARCH_BCM_CYGNUS || COMPILE_TEST)
depends on OF
select PINMUX
select GENERIC_PINCONF
default ARCH_BCM_CYGNUS
help
Say yes here to enable the Broadcom Cygnus IOMUX driver.
The Broadcom Cygnus IOMUX driver supports group based IOMUX
configuration, with the exception that certain individual pins
can be overrided to GPIO function
config PINCTRL_NSP_GPIO
bool "Broadcom NSP GPIO (with PINCONF) driver"
depends on OF_GPIO && (ARCH_BCM_NSP || COMPILE_TEST)
select GPIOLIB_IRQCHIP
select PINCONF
select GENERIC_PINCONF
default ARCH_BCM_NSP
help
Say yes here to enable the Broadcom NSP GPIO driver.
The Broadcom Northstar Plus SoC ChipcommonA GPIO controller is
supported by this driver.
The ChipcommonA GPIO controller support basic PINCONF functions such
as bias pull up, pull down, and drive strength configurations, when
these pins are muxed to GPIO.
config PINCTRL_NS2_MUX
bool "Broadcom Northstar2 pinmux driver"
depends on OF
depends on ARCH_BCM_IPROC || COMPILE_TEST
select PINMUX
select GENERIC_PINCONF
default ARM64 && ARCH_BCM_IPROC
help
Say yes here to enable the Broadcom NS2 MUX driver.
The Broadcom Northstar2 IOMUX driver supports group based IOMUX
configuration.
config PINCTRL_NSP_MUX
bool "Broadcom NSP IOMUX driver"
depends on (ARCH_BCM_NSP || COMPILE_TEST)
depends on OF
select PINMUX
select GENERIC_PINCONF
default ARCH_BCM_NSP
help
Say yes here to enable the Broadcom NSP SOC IOMUX driver.
The Broadcom Northstar Plus IOMUX driver supports pin based IOMUX
configuration, with certain individual pins can be overridden
to GPIO function.