blob: 56de21de2779ea8e0af901458f46b46ffd77c6e5 [file] [log] [blame]
/*
* at91-sama5d2_xplained.dts - Device Tree file for SAMA5D2 Xplained board
*
* Copyright (C) 2015 Atmel,
* 2015 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
#include <dt-bindings/mfd/atmel-flexcom.h>
#include <dt-bindings/gpio/gpio.h>
/ {
model = "Atmel SAMA5D2 Xplained";
compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
chosen {
stdout-path = "serial0:115200n8";
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <12000000>;
};
};
ahb {
usb0: gadget@300000 {
atmel,vbus-gpio = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
};
usb1: ohci@400000 {
num-ports = <3>;
atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */
&pioA PIN_PB10 GPIO_ACTIVE_HIGH
0
>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_default>;
status = "okay";
};
usb2: ehci@500000 {
status = "okay";
};
sdmmc0: sdio-host@a0000000 {
bus-width = <8>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_default>;
non-removable;
mmc-ddr-1_8v;
status = "okay";
};
sdmmc1: sdio-host@b0000000 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_default>;
status = "okay"; /* conflict with qspi0 */
vqmmc-supply = <&vdd_3v3_reg>;
vmmc-supply = <&vdd_3v3_reg>;
};
apb {
spi0: spi@f8000000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_spi0_default>;
status = "okay";
m25p80@0 {
compatible = "atmel,at25df321a";
reg = <0>;
spi-max-frequency = <50000000>;
};
};
macb0: ethernet@f8008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
phy-mode = "rmii";
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
interrupt-parent = <&pioA>;
interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
};
};
pdmic@f8018000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pdmic_default>;
atmel,model = "PDMIC @ sama5d2_xplained";
atmel,mic-min-freq = <1000000>;
atmel,mic-max-freq = <3246000>;
atmel,mic-offset = <0x0>;
status = "okay";
};
uart1: serial@f8020000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
atmel,use-dma-rx;
atmel,use-dma-tx;
status = "okay";
};
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c0_default>;
i2c-sda-hold-time-ns = <350>;
status = "okay";
pmic@5b {
compatible = "active-semi,act8945a";
reg = <0x5b>;
active-semi,vsel-high;
status = "okay";
regulators {
vdd_1v35_reg: REG_DCDC1 {
regulator-name = "VDD_1V35";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
};
vdd_1v2_reg: REG_DCDC2 {
regulator-name = "VDD_1V2";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
};
vdd_3v3_reg: REG_DCDC3 {
regulator-name = "VDD_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_fuse_reg: REG_LDO1 {
regulator-name = "VDD_FUSE";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-always-on;
};
vdd_3v3_lp_reg: REG_LDO2 {
regulator-name = "VDD_3V3_LP";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_led_reg: REG_LDO3 {
regulator-name = "VDD_LED";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_sdhc_1v8_reg: REG_LDO4 {
regulator-name = "VDD_SDHC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
};
charger {
compatible = "active-semi,act8945a-charger";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
interrupt-parent = <&pioA>;
interrupts = <PIN_PB13 GPIO_ACTIVE_LOW>;
active-semi,chglev-gpios = <&pioA PIN_PA12 GPIO_ACTIVE_HIGH>;
active-semi,lbo-gpios = <&pioA PIN_PC8 GPIO_ACTIVE_LOW>;
active-semi,input-voltage-threshold-microvolt = <6600>;
active-semi,precondition-timeout = <40>;
active-semi,total-timeout = <3>;
status = "okay";
};
};
};
pwm0: pwm@f802c000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pwm0_pwm2_default>;
status = "disabled"; /* conflict with leds */
};
flx0: flexcom@f8034000 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&flx0_clk>;
clock-names = "usart";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx0_default>;
atmel,fifo-size = <32>;
status = "okay";
};
};
shdwc@f8048010 {
atmel,shdwc-debouncer = <976>;
atmel,wakeup-rtc-timer;
input@0 {
reg = <0>;
atmel,wakeup-type = "low";
};
};
watchdog@f8048040 {
status = "okay";
};
can0: can@f8054000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can0_default>;
status = "okay";
};
uart3: serial@fc008000 {
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3_default>;
status = "okay";
};
flx4: flexcom@fc018000 {
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
status = "okay";
i2c2: i2c@600 {
compatible = "atmel,sama5d2-i2c";
reg = <0x600 0x200>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <0>, <0>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
clocks = <&flx4_clk>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_flx4_default>;
atmel,fifo-size = <16>;
status = "okay";
};
};
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_default>;
status = "okay";
at24@54 {
compatible = "atmel,24c02";
reg = <0x54>;
pagesize = <16>;
};
};
adc: adc@fc030000 {
vddana-supply = <&vdd_3v3_lp_reg>;
vref-supply = <&vdd_3v3_lp_reg>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
status = "okay";
};
pinctrl@fc038000 {
/*
* There is no real pinmux for ADC, if the pin
* is not requested by another peripheral then
* the muxing is done when channel is enabled.
* Requesting pins for ADC is GPIO is
* encouraged to prevent conflicts and to
* disable bias in order to be in the same
* state when the pin is not muxed to the adc.
*/
pinctrl_adc_default: adc_default {
pinmux = <PIN_PD23__GPIO>;
bias-disable;
};
pinctrl_can0_default: can0_default {
pinmux = <PIN_PC10__CANTX0>,
<PIN_PC11__CANRX0>;
bias-disable;
};
pinctrl_can1_default: can1_default {
pinmux = <PIN_PC26__CANTX1>,
<PIN_PC27__CANRX1>;
bias-disable;
};
/*
* The ADTRG pin can work on any edge type.
* In here it's being pulled up, so need to
* connect it to ground to get an edge e.g.
* Trigger can be configured on falling, rise
* or any edge, and the pull-up can be changed
* to pull-down or left floating according to
* needs.
*/
pinctrl_adtrg_default: adtrg_default {
pinmux = <PIN_PD31__ADTRG>;
bias-pull-up;
};
pinctrl_charger_chglev: charger_chglev {
pinmux = <PIN_PA12__GPIO>;
bias-disable;
};
pinctrl_charger_irq: charger_irq {
pinmux = <PIN_PB13__GPIO>;
bias-disable;
};
pinctrl_charger_lbo: charger_lbo {
pinmux = <PIN_PC8__GPIO>;
bias-pull-up;
};
pinctrl_classd_default: classd_default {
pinmux = <PIN_PB1__CLASSD_R0>,
<PIN_PB2__CLASSD_R1>,
<PIN_PB3__CLASSD_R2>,
<PIN_PB4__CLASSD_R3>;
bias-pull-up;
};
pinctrl_flx0_default: flx0_default {
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
<PIN_PB29__FLEXCOM0_IO1>;
bias-disable;
};
pinctrl_flx4_default: flx4_default {
pinmux = <PIN_PD12__FLEXCOM4_IO0>,
<PIN_PD13__FLEXCOM4_IO1>;
bias-disable;
};
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PD4__TWD1>,
<PIN_PD5__TWCK1>;
bias-disable;
};
pinctrl_key_gpio_default: key_gpio_default {
pinmux = <PIN_PB9__GPIO>;
bias-pull-up;
};
pinctrl_led_gpio_default: led_gpio_default {
pinmux = <PIN_PB0__GPIO>,
<PIN_PB5__GPIO>,
<PIN_PB6__GPIO>;
bias-pull-up;
};
pinctrl_macb0_default: macb0_default {
pinmux = <PIN_PB14__GTXCK>,
<PIN_PB15__GTXEN>,
<PIN_PB16__GRXDV>,
<PIN_PB17__GRXER>,
<PIN_PB18__GRX0>,
<PIN_PB19__GRX1>,
<PIN_PB20__GTX0>,
<PIN_PB21__GTX1>,
<PIN_PB22__GMDC>,
<PIN_PB23__GMDIO>;
bias-disable;
};
pinctrl_macb0_phy_irq: macb0_phy_irq {
pinmux = <PIN_PC9__GPIO>;
bias-disable;
};
pinctrl_pdmic_default: pdmic_default {
pinmux = <PIN_PB26__PDMIC_DAT>,
<PIN_PB27__PDMIC_CLK>;
bias-disable;
};
pinctrl_sdmmc0_default: sdmmc0_default {
cmd_data {
pinmux = <PIN_PA1__SDMMC0_CMD>,
<PIN_PA2__SDMMC0_DAT0>,
<PIN_PA3__SDMMC0_DAT1>,
<PIN_PA4__SDMMC0_DAT2>,
<PIN_PA5__SDMMC0_DAT3>,
<PIN_PA6__SDMMC0_DAT4>,
<PIN_PA7__SDMMC0_DAT5>,
<PIN_PA8__SDMMC0_DAT6>,
<PIN_PA9__SDMMC0_DAT7>;
bias-disable;
};
ck_cd_rstn_vddsel {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA10__SDMMC0_RSTN>,
<PIN_PA11__SDMMC0_VDDSEL>,
<PIN_PA13__SDMMC0_CD>;
bias-disable;
};
};
pinctrl_sdmmc1_default: sdmmc1_default {
cmd_data {
pinmux = <PIN_PA28__SDMMC1_CMD>,
<PIN_PA18__SDMMC1_DAT0>,
<PIN_PA19__SDMMC1_DAT1>,
<PIN_PA20__SDMMC1_DAT2>,
<PIN_PA21__SDMMC1_DAT3>;
bias-disable;
};
conf-ck_cd {
pinmux = <PIN_PA22__SDMMC1_CK>,
<PIN_PA30__SDMMC1_CD>;
bias-disable;
};
};
pinctrl_spi0_default: spi0_default {
pinmux = <PIN_PA14__SPI0_SPCK>,
<PIN_PA15__SPI0_MOSI>,
<PIN_PA16__SPI0_MISO>,
<PIN_PA17__SPI0_NPCS0>;
bias-disable;
};
pinctrl_uart1_default: uart1_default {
pinmux = <PIN_PD2__URXD1>,
<PIN_PD3__UTXD1>;
bias-disable;
};
pinctrl_uart3_default: uart3_default {
pinmux = <PIN_PB11__URXD3>,
<PIN_PB12__UTXD3>;
bias-disable;
};
pinctrl_usb_default: usb_default {
pinmux = <PIN_PB10__GPIO>;
bias-disable;
};
pinctrl_usba_vbus: usba_vbus {
pinmux = <PIN_PA31__GPIO>;
bias-disable;
};
pinctrl_pwm0_pwm2_default: pwm0_pwm2_default {
pinmux = <PIN_PB5__PWMH2>,
<PIN_PB6__PWML2>;
bias-pull-up;
};
};
classd: classd@fc048000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_classd_default>;
atmel,pwm-type = "diff";
atmel,non-overlap-time = <10>;
status = "okay";
};
can1: can@fc050000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can1_default>;
status = "okay";
};
};
};
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_key_gpio_default>;
bp1 {
label = "PB_USER";
gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
wakeup-source;
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_led_gpio_default>;
status = "okay"; /* conflict with pwm0 */
red {
label = "red";
gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
};
green {
label = "green";
gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
};
blue {
label = "blue";
gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};
};