| Bhupesh Sharma | 10489ef | 2021-06-17 11:15:46 +0530 | [diff] [blame] | 1 | // SPDX-License-Identifier: BSD-3-Clause |
| 2 | /* |
| 3 | * Copyright (c) 2021, Linaro Limited |
| 4 | */ |
| 5 | |
| 6 | #include <dt-bindings/input/input.h> |
| 7 | #include <dt-bindings/interrupt-controller/irq.h> |
| 8 | #include <dt-bindings/spmi/spmi.h> |
| 9 | #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 10 | |
| 11 | / { |
| 12 | thermal-zones { |
| 13 | pmm8155au-1-thermal { |
| 14 | polling-delay-passive = <100>; |
| 15 | polling-delay = <0>; |
| 16 | |
| 17 | thermal-sensors = <&pmm8155au_1_temp>; |
| 18 | |
| 19 | trips { |
| 20 | trip0 { |
| 21 | temperature = <95000>; |
| 22 | hysteresis = <0>; |
| 23 | type = "passive"; |
| 24 | }; |
| 25 | |
| 26 | trip1 { |
| 27 | temperature = <115000>; |
| 28 | hysteresis = <0>; |
| 29 | type = "hot"; |
| 30 | }; |
| 31 | |
| 32 | trip2 { |
| 33 | temperature = <145000>; |
| 34 | hysteresis = <0>; |
| 35 | type = "critical"; |
| 36 | }; |
| 37 | }; |
| 38 | }; |
| 39 | }; |
| 40 | }; |
| 41 | |
| 42 | &spmi_bus { |
| 43 | pmic@0 { |
| 44 | compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; |
| 45 | reg = <0x0 SPMI_USID>; |
| 46 | #address-cells = <1>; |
| 47 | #size-cells = <0>; |
| 48 | |
| 49 | pon: power-on@800 { |
| 50 | compatible = "qcom,pm8916-pon"; |
| 51 | reg = <0x0800>; |
| 52 | pwrkey { |
| 53 | compatible = "qcom,pm8941-pwrkey"; |
| 54 | interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 55 | debounce = <15625>; |
| 56 | bias-pull-up; |
| 57 | linux,code = <KEY_POWER>; |
| 58 | |
| 59 | status = "disabled"; |
| 60 | }; |
| 61 | }; |
| 62 | |
| 63 | pmm8155au_1_temp: temp-alarm@2400 { |
| 64 | compatible = "qcom,spmi-temp-alarm"; |
| 65 | reg = <0x2400>; |
| 66 | interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 67 | io-channels = <&pmm8155au_1_adc ADC5_DIE_TEMP>; |
| 68 | io-channel-names = "thermal"; |
| 69 | #thermal-sensor-cells = <0>; |
| 70 | }; |
| 71 | |
| 72 | pmm8155au_1_adc: adc@3100 { |
| 73 | compatible = "qcom,spmi-adc5"; |
| 74 | reg = <0x3100>; |
| 75 | #address-cells = <1>; |
| 76 | #size-cells = <0>; |
| 77 | #io-channel-cells = <1>; |
| 78 | interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 79 | |
| 80 | ref-gnd@0 { |
| 81 | reg = <ADC5_REF_GND>; |
| 82 | qcom,pre-scaling = <1 1>; |
| 83 | label = "ref_gnd"; |
| 84 | }; |
| 85 | |
| 86 | vref-1p25@1 { |
| 87 | reg = <ADC5_1P25VREF>; |
| 88 | qcom,pre-scaling = <1 1>; |
| 89 | label = "vref_1p25"; |
| 90 | }; |
| 91 | |
| 92 | die-temp@6 { |
| 93 | reg = <ADC5_DIE_TEMP>; |
| 94 | qcom,pre-scaling = <1 1>; |
| 95 | label = "die_temp"; |
| 96 | }; |
| 97 | }; |
| 98 | |
| 99 | pmm8155au_1_adc_tm: adc-tm@3500 { |
| 100 | compatible = "qcom,spmi-adc-tm5"; |
| 101 | reg = <0x3500>; |
| 102 | interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 103 | #thermal-sensor-cells = <1>; |
| 104 | #address-cells = <1>; |
| 105 | #size-cells = <0>; |
| 106 | status = "disabled"; |
| 107 | }; |
| 108 | |
| 109 | pmm8155au_1_rtc: rtc@6000 { |
| 110 | compatible = "qcom,pm8941-rtc"; |
| 111 | reg = <0x6000>; |
| 112 | reg-names = "rtc", "alarm"; |
| 113 | interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| 114 | |
| 115 | status = "disabled"; |
| 116 | }; |
| 117 | |
| 118 | pmm8155au_1_gpios: gpio@c000 { |
| 119 | compatible = "qcom,pmm8155au-gpio"; |
| 120 | reg = <0xc000>; |
| 121 | gpio-controller; |
| 122 | #gpio-cells = <2>; |
| 123 | gpio-ranges = <&pmm8155au_1_gpios 0 0 10>; |
| 124 | interrupt-controller; |
| 125 | #interrupt-cells = <2>; |
| 126 | }; |
| 127 | }; |
| 128 | |
| 129 | pmic@1 { |
| 130 | compatible = "qcom,pmm8155au", "qcom,spmi-pmic"; |
| 131 | reg = <0x1 SPMI_USID>; |
| 132 | #address-cells = <1>; |
| 133 | #size-cells = <0>; |
| 134 | }; |
| 135 | }; |
